Sony DCR-TRV30 / DCR-TRV30E (serv.man2) Service Manual ▷ View online
5-3
z
z
z
z z
z z
z z
z
*
2
z z
z
*
2
z z
z
z z
z
z
z z
z
*
2
z z
*
2
z z
z
*
2
z z
z
z z
z
z
z z
z z z
z
*
2
z z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z z
z
z z
z
z z
CD-320 board
(COMPLETE)
CK-102 board
(COMPLETE)
JK-207 board
(COMPLETE)
LB-072 board
(COMPLETE)
MI-043 board
(COMPLETE)
PD-145 board
(COMPLETE)
SE-121 board
(COMPLETE)
VC-264 board
(COMPLETE)
VC-264 board IC451
(EEPR
OM)
VC-264 board IC4701
(EEPR
OM)
VC-264 board IC1406
(Flash memory)
Supporting
RadarWRadarW
RadarWRadarW
RadarW
Adjustment
Section
Initialization
of B, C, D, E,
F, 7, 8 page data
Camera
Color EVF
LCD
System control
Servo & RF
Video
IR
Mechanism
Adjustment
Initialization of C, D, 8 page data
Initialization of B page data
Initialization of E, F, 7 page data
40.5/54MHz origin oscillation adj.
Hall adj.
MAX GAIN adj.
CCD output 2ch matching adj.
MR adj.
Flange back adj.
Color reproduction adj.
AWB & LV standard data input
Auto white balance adj.
Mechanical shutter adj.
Angular velocity sensor sensitivity adj.
Strobe light level adj.
Strobe white balance adj. & check
VCO adj.
RGB AMP adj.
Contrast adj.
Backlight adj.
White balance adj.
VCO adj.
RGB AMP adj.
Contrast adj.
V-COM level adj.
V-COM adj.
White balance adj.
Serial No. input
CAP FG duty adj.
Switching position adj.
AGC center level adj.
APC & AEQ adj.
PLL f
0
& LPF f
0
adj.
Chroma BPF f
0
adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IR video carrier frequency adj.
IR video deviation adj.
IR audio deviation adj.
Tape path adj.
Board replacement
EEPROM
replacement
Note2:
When the repair is finished, confirm the
following items.
following items.
1.
Shoot the all black subject (Attach the lens
cap and shoot), and confirm that a vertical
line is not displayed in the center of the
screen, and that there is no difference in
left-right brightness level of the screen.
cap and shoot), and confirm that a vertical
line is not displayed in the center of the
screen, and that there is no difference in
left-right brightness level of the screen.
2.
Shoot a subject of low light, and confirm
that a vertical line is not displayed in the
center of the screen, and that there is no
difference in left-right brightness level of
the screen.
that a vertical line is not displayed in the
center of the screen, and that there is no
difference in left-right brightness level of
the screen.
3.
Shoot a subject of normal light, and
confirm that a vertical line is not displayed
in the center of the screen, and that there
is no difference in left-right brightness
level of the screen.
When the above symptom occurs, perform
the whole process of “CCD Output 2ch
Matching Adjustment”.
confirm that a vertical line is not displayed
in the center of the screen, and that there
is no difference in left-right brightness
level of the screen.
When the above symptom occurs, perform
the whole process of “CCD Output 2ch
Matching Adjustment”.
*1: When replacing the camera microproces-
sor ver. 1.0 with the camera microproces-
sor ver. 2.0 or later, change the data of the
“Fixed data-2 (*1)” address shown in the
E, 7 page data table. Refer to “1-2-3. INI-
TIALIZATION OF E, F, 7 PAGE DATA”.
sor ver. 2.0 or later, change the data of the
“Fixed data-2 (*1)” address shown in the
E, 7 page data table. Refer to “1-2-3. INI-
TIALIZATION OF E, F, 7 PAGE DATA”.
*2: Perform this adjustment when replace the
CCD imager (IC101) and this board at the
same time.
same time.
Table. 5-1-1(2).
5-4
J-1
J-2
J-6
J-3
J-7
J-8
J-4
J-5
Fig. 5-1-1.
J-9
J-10
J-11
J-12
Ref. No.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
J-12
Name
Filter for color temperature correction (C14)
ND filter 1.0
ND filter 0.4
ND filter 0.1
Pattern box PTB-450
Color chart for pattern box
Adjustment remote commander (RM-95 upgraded).
(Note 1)
(Note 1)
Siemens star chart
Clear chart for pattern box
CPC-8 jig
Background paper
IR receiver jig
Mini pattern box
Camera table
Parts Code
J-6080-058-A
J-6080-808-A
J-6080-806-A
J-6080-807-A
J-6082-200-A
J-6020-250-A
J-6082-053-B
J-6080-875-A
J-6080-621-A
J-6082-388-A
J-2501-130-A
J-6082-383-A
J-6082-353-B
J-6082-384-A
Usage
Auto white balance adjustment/check
White balance adjustment/check
White balance adjustment/check
White balance check
White balance check
White balance check
For checking the flange back
For adjusting the video section
For adjusting the color viewfinder
For adjusting the LCD block
For adjusting the color viewfinder
For adjusting the LCD block
For adjusting the flash unit
For adjusting the IR transmitter
For adjusting the flange back
For adjusting the flange back
5-1. CAMERA SECTION ADJUSTMENT
1-1.
PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)
1-1-1.
List of Service Tools
• Oscilloscope
• Color monitor
• Vectorscope
• Regulated power supply
• Digital voltmeter
Note:
If the micro processor IC in the adjustment remote commander is
not the new micro processor (UPD7503G-C56-12), the pages cannot
be switched. In this case, replace with the new micro processor (8-
759-148-35).
not the new micro processor (UPD7503G-C56-12), the pages cannot
be switched. In this case, replace with the new micro processor (8-
759-148-35).
5-5
Fig. 5-1-2.
1-1-2.
Preparations
Note 1:
For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.
DISASSEMBLY”.
Note 2:
When performing only the adjustments, the lens block and boards
need not be disassembled.
need not be disassembled.
1)
Connect the equipment for adjustments according to Fig. 5-1-2.
Note 3:
As removing the cabinet (R) (removing the VC-264 board CN003)
means removing the lithium 3V power supply (BT3201), data such
as date, time, user-set menus will be lost. After completing
adjustments, reset these data. If the cabinet (R) has been removed,
the self-diagnosis data, data on history of use (total drum rotation
time etc. ) will be lost. Before removing, note down the data of
page: 2, address: A2 to AA (data on history of use) and the data of
page: 2, address: B0 to C6 (self-diagnosis data). (Refer to “5-4.
Service Mode” for the data on the history use and the self-diagnosis
data.)
means removing the lithium 3V power supply (BT3201), data such
as date, time, user-set menus will be lost. After completing
adjustments, reset these data. If the cabinet (R) has been removed,
the self-diagnosis data, data on history of use (total drum rotation
time etc. ) will be lost. Before removing, note down the data of
page: 2, address: A2 to AA (data on history of use) and the data of
page: 2, address: B0 to C6 (self-diagnosis data). (Refer to “5-4.
Service Mode” for the data on the history use and the self-diagnosis
data.)
Note 4:
Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (FK-1800) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
on with the control switch block (FK-1800) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
Note 5:
Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
1.5 m
Front of the lens
Pattern box
5-6
Fig. 5-1-3.
CN3201
CN1801
CN3207
CN3202
CN3204
CN3205
CN3206
FP-325
VC-264 board
CK-102 board
CN007 CN006
CN011
CN003
CN012 CN601
CN009
CN008
CN1601
CN301
CN001
FP-328
FP-327
Adjustment remote
commander
AC-power adaptor
(8.4 Vdc)
(8.4 Vdc)
AC-L10,
AC-VQ800 etc.
AC-VQ800 etc.
Front panel block
MI-043 board
CN2003
CN2003
LANC jack
AUDIO/VIDEO
jack
jack
Cabinet (R)
Color monitor
Vector scope
Terminated
at 75
at 75
Ω
VIDEO
(Yellow)
(Yellow)
AUDIO L
(White)
(White)
AUDIO R
(Red)
(Red)
DC IN jack
CPC-8 jig
(J-6082-388-A)
Must be connected when
performing the video, EVF or
LCD system adjustments.
performing the video, EVF or
LCD system adjustments.
Must be connected when
using the Viewfinder.
using the Viewfinder.
Click on the first or last page to see other DCR-TRV30 / DCR-TRV30E (serv.man2) service manuals if exist.