Sony DCR-TRV15E / DCR-TRV17E (serv.man2) Service Manual ▷ View online
5-5
Fig. 5-1-2.
1-1-2.
Preparations
Note 1:
For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.
DISASSEMBLY”.
Note 2:
When performing only the adjustments, the lens block and boards
need not be disassembled.
need not be disassembled.
1)
Connect the equipment for adjustments according to Fig. 5-1-2.
Note 3:
As removing the cabinet (R) (removing the VC-260 board CN009)
means removing the lithium 3V power supply (BT8301), data such
as date, time, user-set menus will be lost. After completing
adjustments, reset these data. If the cabinet (R) has been removed,
the self-diagnosis data, data on history of use (total drum rotation
time etc. ) will be lost. Before removing, note down the data of
page: 2, address: A2 to AA (data on history of use) and the data of
page: 2, address: B0 to C6 (self-diagnosis data). (Refer to “5-
4.Service Mode” for the data on the history use and the self-
diagnosis data.)
means removing the lithium 3V power supply (BT8301), data such
as date, time, user-set menus will be lost. After completing
adjustments, reset these data. If the cabinet (R) has been removed,
the self-diagnosis data, data on history of use (total drum rotation
time etc. ) will be lost. Before removing, note down the data of
page: 2, address: A2 to AA (data on history of use) and the data of
page: 2, address: B0 to C6 (self-diagnosis data). (Refer to “5-
4.Service Mode” for the data on the history use and the self-
diagnosis data.)
Note 4:
Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (PS-1700) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
on with the control switch block (PS-1700) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
Note 5:
Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
1.5 m
Front of the lens
Pattern box
5-6
Fig. 5-1-3.
JK-204 board
CN3102
CN3102
CN011
CN7501
CN002
CN012
CN601
CN014
CN007
CN010
CN009
CN008
CN5604
CN013
CN004
CN302
CN005
CN1153
CN1152
CN1901
CN5501
CN5502
CN5703
CN5701
Multi CPC jig
(J-6082-311-A)
(J-6082-311-A)
(
*
1)
(
*
1)
AC-power adaptor
(8.4Vdc)
(8.4Vdc)
AC-L10,
AC-VQ800 etc.
AC-VQ800 etc.
Battery terminal
Front panel
block
block
Lens block
Adjustment remote
commander
commander
Cabinet (R)
Color monitor
Vector scope
Terminated
at 75
at 75
Ω
VIDEO
(Yellow)
(Yellow)
AUDIO L
(White)
(White)
AUDIO R
(Red)
(Red)
DC IN
jack
jack
CPC-8 jig
(J-6082-388-A)
(J-6082-388-A)
LANC jack
VC-260 board
MS-070 board (
*
1)
To PD-143 board
CN5701
CN5701
*
1 : DCR-TRV17E model only
CK-101 board
CN8301
CN8301
PD-143 board
Extension cable
(100P)
(J-6082-352-A)
(100P)
(J-6082-352-A)
Must be connected when
performing the LCD
system adjustments.
performing the LCD
system adjustments.
Must be connected when
using the focus ring.
using the focus ring.
Must be connected when
performing the LCD
system adjustments.
performing the LCD
system adjustments.
AUDIO/VIDEO
jack
jack
Must be connected
Must be connected
Must be connected (
*
1)
Must be connected
when performing the
video system or color
EVF system adjust-
ments.
when performing the
video system or color
EVF system adjust-
ments.
5-7
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
adjustments without loading cassette.
1.
POWER switch (PS-1700 block) ........................... CAMERA
2.
NIGHT SHOT switch (Lens block) ................................. OFF
3.
DEMO MODE (Menu setting) ........................................ OFF
4.
DIGITAL ZOOM (Menu setting) .................................... OFF
5.
STEADY SHOT (Menu setting) ...................................... OFF
6.
PROGRAM AE (Menu setting) ................................... AUTO
7.
WHITE BALANCE (Menu setting) ............................ AUTO
8.
16 : 9 WIDE (Menu setting) ............................................ OFF
9.
PICTURE EFFECT (Menu setting) ................................. OFF
10. DIGITAL EFFECT (Menu setting) .................................. OFF
11. DISPLAY (Menu setting) .................................. V-OUT/LCD
12. DISPLAY (CK-101 board) ............................................... ON
13. FOCUS switch (CK-101 board) ............................ MANUAL
11. DISPLAY (Menu setting) .................................. V-OUT/LCD
12. DISPLAY (CK-101 board) ............................................... ON
13. FOCUS switch (CK-101 board) ............................ MANUAL
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig.5-1-4.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
Fig. 5-1-5.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
5-8
1-2.
INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE
DATA
DATA
1-2-1.
INITIALIZATION OF C, D, 8 PAGE DATA
1. Initializing the C, D, 8 Page Data
Note1: If “Initializing the C, D, 8 Page Data” is performed, all
data of the C page, D page and 8 page will be initialized.
(It is impossible to initialize a single page.)
(It is impossible to initialize a single page.)
Note2:
If the C, D, 8 page data has been initialized, the following
adjustments need to be performed again.
1) Modification of C, D, 8 page data
2) Serial No. input
3) Servo and RF system adjustments
4) Video system adjustments
5) Color viewfinder system adjustments
6) LCD system Adjustments
adjustments need to be performed again.
1) Modification of C, D, 8 page data
2) Serial No. input
3) Servo and RF system adjustments
4) Video system adjustments
5) Color viewfinder system adjustments
6) LCD system Adjustments
Adjusting page
C
Adjusting Address
10 to FF
Adjusting page
D
Adjusting Address
10 to FF
Adjusting page
8
Adjusting Address
00 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data
2
3
81
Check that the data is “00”.
3
3
80
0A
Set the data, and press the PAUSE
button.
button.
4
3
80
Check that the data changes to “1A”
5
Perform “Modification of C, D, 8
Page Data”.
Page Data”.
2. Modification of C, D, 8 Page Data
If the C, D, 8 page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.
“Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of C, D, 8 Page data
Order Page Address Data
Procedure
1
2
00
29
Set the data
2
2
01
29
Set the data, and press the PAUSE
button.
button.
Note:
If the following symptoms occur after completing of the
“Modification of C, D, 8 page data”, check that the data of the “Fixed
data-2” addresses of D page are same as those of the same model of
the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
“Modification of C, D, 8 page data”, check that the data of the “Fixed
data-2” addresses of D page are same as those of the same model of
the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
3. C Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8
Page Data”.)
Address
Remark
Initial value
00 to 0F
10
11
12
13
14 to 15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23 to 24
25
26
27
28
29
2A to 2B
2C
2D to 42
43
44 to 4B
4C
4D
4E to 4F
50
51
52 to 6F
70
71
72
EE
00
00
00
E0
2A
2A
32
32
25
3E
3E
DC
99
88
E3
A1
04
20
03
Switching position adj.
Fixed data-1
Cap FG duty adj.
Fixed data-2
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
AGC center level adj.
PLL fo adj.
APC adj.
LPF fo adj.
Fixed data-1
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Chroma BPF fo adj.
PLL fo fine adj.
Fixed data-1
APC adj.
Fixed data-1
Fixed data-2
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Click on the first or last page to see other DCR-TRV15E / DCR-TRV17E (serv.man2) service manuals if exist.