Sony DCR-TRV12E / DCR-TRV14E / DCR-TRV19 / DCR-TRV19E (serv.man4) Service Manual ▷ View online
6-19
DCR-TRV12E/TRV14E/TRV19/TRV19E
6. Optical Axis Adjustment
Align the lens Optical Axis with that of the CCD imager. If deviated,
center of picture can lose focus when zoom is operated from the
WIDE end to the TELE end.
center of picture can lose focus when zoom is operated from the
WIDE end to the TELE end.
Subject
Siemens star
Measurement Point
Check on the monitor TV
Measuring Instrument
Adjustment Page
F
Adjustment Address
46
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment”.
back adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 48 is “00”. If not, set data:
00 to this address.
00 to this address.
Switch setting:
1)
1)
POWER ................................................................. CAMERA
2)
DIGITAL ZOOM (Menu setting) .................................... OFF
3)
STEADY SHOT (Menu setting) ...................................... OFF
Preparations before adjustments:
1)
1)
Playback the monoscope segment of the system check tape
(XH5-5 (NTSC), XH5-5P (PAL),).
(XH5-5 (NTSC), XH5-5P (PAL),).
2)
Attach the optical axis frame chart (transparent) on the monitor
TV screen. Center of monoscope image and that of optical axis
frame must be agree.
TV screen. Center of monoscope image and that of optical axis
frame must be agree.
3)
Set to the camera mode.
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: F, address: 46, set data: 00, and press the PAUSE
button.
button.
3)
Place the Siemens star 2.0 m away from the front of the lens.
4)
Shoot the Siemens star with the zoom TELE end.
5)
Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.
Siemens star is located in the center of the optical axis frame.
6)
Shoot the Siemens star with the zoom WIDE end.
7)
Measure on the monitor TV screen in which area of the optical
axis frame the center of the Siemens star is located. Measure
the amount of displacement (distance between the center of
the Siemens star and the center of the optical axis frame.) The
measurement value is named L1.
axis frame the center of the Siemens star is located. Measure
the amount of displacement (distance between the center of
the Siemens star and the center of the optical axis frame.) The
measurement value is named L1.
8)
Read the correction data corresponding to the area from Table
6-1-9.
6-1-9.
9)
Input the correction data to page: F, address: 46, and press the
PAUSE button
PAUSE button
10) Shoot the Siemens star with the zoom TELE end.
11) Point the lens toward the Siemens star chart until center of the
11) Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.
12) Shoot the Siemens star with the zoom WIDE end.
13) Measure the amount of displacement (distance between the
13) Measure the amount of displacement (distance between the
center of the Siemens star and the center of the optical axis
frame.) The measurement value is named L2.
frame.) The measurement value is named L2.
14) Compare the values L1 and L2, and confirm that L2 is smaller
than L1. If L2 is lager than L1, select page: F, address: 46, set
data: 00, and press the PAUSE button.
data: 00, and press the PAUSE button.
Table 6-1-9.
Processing after Completing
Adjustments:
1)
Select page: 0, address: 01, and set data: 00.
Fig. 6-1-9.
Area
1
2
3
4
5
6
7
8
Correction data
(Page: F, address: 46)
01
02
03
04
05
06
07
08
Display phase
22.6
°
to 67.5
°
67.6
°
to 112.5
°
112.6
°
to 157.5
°
157.6
°
to 202.5
°
202.6
°
to 247.5
°
247.6
°
to 292.5
°
292.6
°
to 337.5
°
337.6
°
to 22.5
°
6-20
DCR-TRV12E/TRV14E/TRV19/TRV19E
7. Picture Frame Setting
Subject
Color bar chart
(Color reproduction adjustment frame)
(1.5m from the front of the lens)
(Color reproduction adjustment frame)
(1.5m from the front of the lens)
Measurement Point
Video terminal of AUDIO/VIDEO jack
Measuring Instrument
Oscilloscope and TV monitor
Specified Value
A=B, C=D, E=F
Note1:
The following adjustments should be carried out upon completion
of “Flange back adjustment” and “Optical Axis adjustment”.
of “Flange back adjustment” and “Optical Axis adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Switch setting:
1)
1)
POWER ................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Setting method:
1)
1)
Select page: 6, address: 48, and set data: 02.
2)
Adjust the zoom and the camera direction, and set to the
specified position.
specified position.
3)
Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in following
adjustments using “Color reproduction adjustment frame”.
and adjust the picture frame to this position in following
adjustments using “Color reproduction adjustment frame”.
Processing after Completing Camer
a System Adjustments:
After completing the camera system adjustments, release the data
settings.
1)
settings.
1)
Select page: 6, address: 48, and set data: 00.
Check on the oscilloscope
1. Horizontal period
Fig. 6-1-10.
2. Vertical period
Fig. 6-1-11.
Check on the monitor TV (Underscanned mode)
Fig. 6-1-12.
A=B
C=D
A
B
C
D
E=F
V
E
F
Color bar chart picture frame
Monitor TV picture frame
6-21
DCR-TRV12E/TRV14E/TRV19/TRV19E
Burst position
For NTSC model
Burst position
For PAL model
Fig. 6-1-13.
8. Color Reproduction Adjustment
Adjust the color Separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measurement Point
Video terminal of AUDIO/VIDEO jack
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
23, 25, 2A, 2B
Specified Value
All color luminance points should settle
within each color reproduction frame.
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment” and “Optical Axis Adjustment”.
back adjustment” and “Optical Axis Adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
NTSC model: DCR-TRV19
PAL model: DCR-TRV12E/TRV14E/TRV19E
PAL model: DCR-TRV12E/TRV14E/TRV19E
Switch setting:
1)
1)
POWER ................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 6, address: 48, and set data: 02.
3)
Select page: 6, address: 9D, and set data: 29.
4)
Select page: 6, address: 01, set data: 3D, and press the PAUSE
button.
button.
5)
Select page: F, address: 80, set the following data, and press
the PAUSE button.
the PAUSE button.
37 (NTSC), B7 (PAL)
6)
Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.
the burst luminance point to the burst position of the color
reproduction frame.
7)
Change the data of page: F, address: 23, 25, 2A and 2B, and
settle each color luminance point in each color reproduction
frame.
settle each color luminance point in each color reproduction
frame.
Note:
Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data
will not be written to the memory.
commander before changing the addresses. If not, the new data
will not be written to the memory.
Processing after Completing
Adjustments:
1)
Select page: 6, address: 01, set data: 00, and press the PAUSE
button.
button.
2)
Select page: 6, address: 48, and set data: 00.
3)
Select page: 6, address: 9D, and set data: 00.
4)
Select page: 0, address: 01, and set data: 00.
6-22
DCR-TRV12E/TRV14E/TRV19/TRV19E
9. MAX GAIN Adjustment
Setting the minimum illumination.
If it is not consistent, the image level required for taking subjects in
low illuminance will not be produced (dark).
If it is not consistent, the image level required for taking subjects in
low illuminance will not be produced (dark).
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Adjustment Page
F
Adjustment Address
17
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment” and “Optical Axis Adjustment”.
back adjustment” and “Optical Axis Adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Note4:
NTSC model: DCR-TRV19
PAL model: DCR-TRV12E/TRV14E/TRV19E
PAL model: DCR-TRV12E/TRV14E/TRV19E
Switch setting:
1)
1)
POWER ................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
02
Set the data.
3
6
96
Set the following data.
24 (NTSC), 18(PAL)
24 (NTSC), 18(PAL)
4
6
97
00
Set the data.
5
6
01
6F
Set the data, and press PAUSE
button.
button.
6
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
Note5:
The adjustment data will be automatically input to page: F, address:
17.
17.
Processing after Completing
Adjustments
Order Page Address Data
Procedure
1
6
48
00
Set the data.
2
6
96
00
Set the data.
3
6
97
00
Set the data.
4
6
01
00
Set the data, and press PAUSE
button.
button.
5
0
01
00
Set the data.
10. LV Standard Data Input
And adjust the normal coefficient of the light value.
Subject
Clear chart
(Color reproduction adjustment frame)
(Color reproduction adjustment frame)
Measurement Point
Display data of page 1 (Note4)
Measuring Instrument
Adjustment remote commander
Adjustment Page
F
Adjustment Address
18, 19
Specified Value
0FF0 to 1010
Note1:
This adjustment should be carried out upon completion of “Flange
back adjustment”, “Optical Axis Adjustment”, “Color reproduction
adjustment” and “MAX GAIN Adjustment”.
back adjustment”, “Optical Axis Adjustment”, “Color reproduction
adjustment” and “MAX GAIN Adjustment”.
Note2:
The data of page: 0, address: 10 must be “00”.
Note3:
Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
6, address: 01, set data: 00, and press the PAUSE button.
Note4:
Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX
Display data
Switch setting:
1)
1)
POWER ................................................................. CAMERA
2)
NIGHT SHOT .................................................................. OFF
3)
DIGITAL ZOOM (Menu setting) .................................... OFF
4)
STEADY SHOT (Menu setting) ...................................... OFF
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
6
48
02
Set the data.
3
6
01
0D
Set the data, and press PAUSE
button.
button.
4
6
02
Check that the data changes to
“01”. (Note5)
“01”. (Note5)
5
0
03
1E
Set the data.
6
1
Check that the display data
(Note5) satisfies the specified
value.
(Note5) satisfies the specified
value.
Note5:
The adjustment data will be automatically input to page: F, address:
18, 19.
18, 19.
Processing after Completing
Adjustments
Order Page Address Data
Procedure
1
6
01
00
Set the data, and press PAUSE
button.
button.
2
6
48
00
Set the data.
3
0
03
00
Set the data.
4
0
01
00
Set the data.
5
Perform “Auto White Balance
Standard Data Input”.
Standard Data Input”.
Click on the first or last page to see other DCR-TRV12E / DCR-TRV14E / DCR-TRV19 / DCR-TRV19E (serv.man4) service manuals if exist.