DOWNLOAD Sony DCR-SR32E / DCR-SR33E / DCR-SR42 / DCR-SR42A / DCR-SR42E / DCR-SR52E / DCR-SR62 / DCR-SR62E / DCR-SR72E / DCR-SR82 / DCR-SR82C / DCR-SR82E (serv.man4) Service Manual ↓ Size: 753.77 KB | Pages: 56 in PDF or view online for FREE

6-19

DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_ADJ

The adjustment items of camera system adjustment are as listed in
Table 6-1-5. The Automatic Adjustment Program divides the ad-
justment items into seven, camera adjustment 1-7. Clicking either
CAMERA Adjustment Start button allows the adjustment item
which corresponds to that button to be executed.
The adjustment conditions of the subject and filter vary depend-
ing on which item is adjusted. The Adjustment Program displays
an instruction for the subject and filter as a message during the
adjustment.

CAMERA
Adjustment 1

HALL Adj.

Not required

11

61

0250 to 0258

Siemens star chart with ND filter for
minipattern box (Note) or
Flange back adjustment jig

Flange back adjustment chart and
subject more than 500 m away

CAMERA
Adjustment 3

Flange Back Check

Siemens star chart

-

-

-

CAMERA
Adjustment 4

Optical Axis Adj.

Clear chart
(2.0 m from the front of lens)

11

61

0E04, 0E05

F No. Standard Data Input

11

61

0260 to 026F

MAX GAIN Adj.

11

61

025E

Color Reproduction Adj.

Color bar chart and Clear chart
(Color reproduction adjustment frame)

11

61

0061, 0063,
0067, 0068

Color Reproduction Check

Color bar chart
(Color reproduction adjustment frame)

-

-

-

AWB Standard Data Input

11

61

0074 to 007B

LV Standard Data Input

11

61

025C, 025D

AWB Adj.

Clear chart
(All White frame)
Filter C14 for color temperature
correction

11

61

0070 to 0073,
008C to 0093

AWB Check

Clear chart
(All White frame)
ND filter 1.0, 0.4 and 0.1

-

-

-

CAMERA
Adjustment 7

0020 to 0030,
004C, 004D

 Dark Siemens star chart.

Clear chart
(All White frame)

61

11

CAMERA
Adjustment 2

Flange Back Adj.

Clear chart
(Center frame)

CAMERA
Adjustment 5

CAMERA
Adjustment 6

6-20

DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. HALL Adj.
3. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 1.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) If “1. Data Setting during Camera Adj.” completed success-

fully, and the items “2. HALL Adj.” and “3. Release of Data
Setting during Camera Adj.” will be executed.

4) Upon successful completion of all items of the CAMERA

Adjustment 1, the following message is displayed. Click the
[OK] button.

6-21

DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_ADJ

When using the flange back adjustment jig, take care of
the following points:
• For the illumination, use a light source such as an in-

candescent lamp or inverter type fluorescent light free
from flickering.

• Do not make an adjustment in the environment where

fluorescent lamp flickering occurs even if the illumi-
nance can be ensured with the room illumination only.
Use an incandescent lamp or inverter type fluorescent
light at a place free from the influence of room illumi-
nation.

1) Install the flange back adjustment jig so that the distance be-

tween it and the front of lens of camera is less than 3 cm.

2) Make the height of flange back adjustment jig and the camera

equal.

3) Check that the center of chart meets the center of shot image

screen with the zoom lens at TELE end and WIDE end respec-
tively.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back Adj.” and “3.

Release of Data Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 2, the following message is displayed. Click the
[OK] button.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back Adj.
3. Release of Data Setting during Camera Adj.

[Preparation (Using the minipattern box)]
1) The minipattern box is installed as shown in the following fig-

ure.

 The attachment lenses are not used.

2) Install the minipattern box so that the distance between it and

the front of lens of camera is less than 3 cm.

3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the

specified voltage 

± 0.01 Vdc.

5) Check that the center of Siemens star chart meets the center of

shot image screen with the zoom lens at TELE end and WIDE
end respectively.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the
minipattern box.

Minipattern box

Below 3 cm

Camera

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±

 0.01 Vdc

Output current : more than 3.5 A

Flange back adjustment jig

Below 3 cm

Camera

6-22

DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back (1) Adj.
3. Release of Data Setting during Camera Adj.

[Preparation]
1) Place the Flange back adjustment chart at 2 m position away

from the lens.

2) Check that the center of Flange back adjustment chart meets

the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.

[Adjusting method]
1) Click the [Start $1%] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back (1) Adj.” and “3.

Release of Data Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 2 (1), the following message is displayed. Click
the [OK] button.

6) Perform “CAMERA Adjustment 2 (2)”.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back (2) Adj.
3. Release of Data Setting during Camera Adj.

[Preparation]
1) Set the zoom lens to the TELE end and expose a subject that is

more than 500 m away.

(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the screen)

[Adjusting method]
1) Click the [Start $2%] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back (2) Adj.” will be

executed.
The following message is displayed during the execution of
adjustment, and then place the ND filter on the lens so as to
obtain the optimum image.

5) If “2. Flange Back Adj.” completed successfully, “3. Release

of Data Setting during Camera Adj.” will be executed.

6) Upon successful completion of all items of the CAMERA

Adjustment 2 (2), the following message is displayed. Click
the [OK] button.