Sony DCR-SR100 / DCR-SR100E / DCR-SR90E (serv.man4) Service Manual ▷ View online
6-55
DCR-SR90E/SR100/SR100E_ADJ
2.
Emergence Memory Address
2-1. Emergency Memory Address (Camera section)
Page 19
Address 87 to 8A
Note: If reading/writing data on pages 19, set data: 01 to page:
0, address: 10, and then select pages: 9. By this data set-
ting, the pages 19 can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
ting, the pages 19 can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
Address
Contents
87
EMG code when first error occurs
88
EMG code when second error occurs
89
EMG code when third error occurs
8A
EMG code when last error occurs
When no error occurs in this unit, data “00” is written in the above
addresses (87 to 8A). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (87). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (88).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (8A).
Note: After completing adjustments, be sure to initialize the data
addresses (87 to 8A). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (87). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (88).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (8A).
Note: After completing adjustments, be sure to initialize the data
of addresses 87 to 8A to “00”.
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
6
01
FD
Press PAUSE (Write) button.
3
6
02
Check the data changes to
“01”.
“01”.
4
6
01
00
Press PAUSE (Write) button.
5
0
01
00
2-2. EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in 19
page, addresses 87 to 8A. The type of error indicated by the code
are shown in the following table.
Codes corresponding to the errors which occur are written in 19
page, addresses 87 to 8A. The type of error indicated by the code
are shown in the following table.
Code
Emergency Type
00
No error
2-5.
SERVICE MODE
Note: Before performing the adjustment, check the data of page:
0, address: 10 is “00”. If not, select page: 0, address: 00,
and set data “00”.
and set data “00”.
1.
Setting the Test Mode
Page A
Address 10
Data
Function
00
Normal
01
Forced MOVIE mode
02
Forced PLAY/EDIT mode
05
Forced STILL mode
06
Forced LINE INPUT mode
• Before setting the data , select page: 0, address: 01, and set data:
01.
• For page A, the data set will be recorded in the non-volatile
memory by pressing the PAUSE (Write) button of the adjust-
ment remote commander. In this case, take note that the test
mode will not be exited even when the main power is turned off
(8.4 Vdc).
ment remote commander. In this case, take note that the test
mode will not be exited even when the main power is turned off
(8.4 Vdc).
• After completing adjustments/repairs, be sure to return the data
of this address to 00, and press the PAUSE (Write) button of the
adjustment remote commander. And select page: 0, address: 01,
and set data: 00.
adjustment remote commander. And select page: 0, address: 01,
and set data: 00.
6-56
DCR-SR90E/SR100/SR100E_ADJ
Page
Address
bit3 to bit0 discrimination
bit7 to bit4 discrimination
Display on the adjustment remote commander
3.
Bit Value Discrimination
Bit values must be discriminated using the display data of the ad-
justment remote commander for the following items. Us the table
below to discriminate if the bit value is “1” or “0”.
justment remote commander for the following items. Us the table
below to discriminate if the bit value is “1” or “0”.
(Example) If the remote commander display is “8E”, bit value from
bit 7 to bit 4 can be discriminated from the column A,
and those from bit 3 to bit 0 from column B.
and those from bit 3 to bit 0 from column B.
Display on the
adjustment
remote
commander
0
1
2
3
4
5
6
7
8
9
A (
A
)
B (
b
)
C (
C
)
D (
d
)
E (
E
)
F (
F
)
Bit values
bit3
or
bit7
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
bit2
or
bit6
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
bit1
or
bit5
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
bit0
or
bit4
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
A
B
4.
Switch Check (1)
Page 7
Address 8C, 8D and 8F
Note: Check that the data of page: 0, address: 10 is “00”.
Using method:
1) Select page: 7, address: 8C, 8D and 8F.
2) By discriminating the display data, the pressed key can be dis-
1) Select page: 7, address: 8C, 8D and 8F.
2) By discriminating the display data, the pressed key can be dis-
criminated.
Address
8F
(KEY AD0)
(IC2501 <
61
)
8C
(KEY AD2)
(IC2501 <
58
)
8D
(KEY AD4)
(IC2501 <
59
)
00 to 0B
PHOTO
(REC)
(PS80400 block)
(S003)
0C to 25
START/STOP
(PS80400 block)
(S002)
26 to 40
41 to 5F
60 to 83
84 to AD
FLASH
(PS80400 block)
(S005)
AE to E1
NIGHTSHOT
ON
(NS-021 board)
(S8602)
E2 to FF
No key input
NIGHTSHOT
OFF
(NS-021 board)
(S8602)
PANEL
NORMAL
(FP-432 flexible)
(S001)
Data
PANEL
REVERSE
(FP-432 flexible)
(S001)
PHOTO
(FREEZE)
(PS80400 block)
(S004)
6-57
DCR-SR90E/SR100/SR100E_ADJ
5.
Switch Check (2)
Page 7
Address 96 and 98
Note: Check that the data of page: 0, address: 10 is “00”.
Using method:
1) Select page: 7, address: 96 and 98.
2) By discriminating the display data, the pressed key can be dis-
1) Select page: 7, address: 96 and 98.
2) By discriminating the display data, the pressed key can be dis-
criminated.
Address
96
(KEY AD1)
(IC2301 <
(IC2301 <
A27
)
98
(KEY AD3)
(IC2301 <
(IC2301 <
B27
)
00 to 0C
REC
START/STOP
(SB9000 block)
(SB9000 block)
(S003)
DVD BURN
(CK-162 board)
(S7306)
0D to 26
ZOOM W
(SB9000 block)
(S001)
EASY
(CK-162 board)
(S7303)
27 to 43
ZOOM T
(SB9000 block)
(S002)
BACK LIGHT
(NS-021 board)
(S8601)
44 to 63
WIDE
SELECT
(CK-162 board)
(S7305)
64 to 8A
PANEL
OPEN
(CK-162 board)
(S7304)
8B to B2
B3 to E1
E2 to FF
No key input
PANEL
CLOSE
CLOSE
(CK-162 board)
(S7304)
Data
6.
Switch Check (3)
Page 7
Address 50
Note: Check that the data of page: 0, address: 10 is “00”.
Using method:
1) Select page: 7, address: 50.
2) By discriminating the bit value of display data, the state of the
1) Select page: 7, address: 50.
2) By discriminating the bit value of display data, the state of the
switch can be discriminated.
Bit
Function
When bit value = 1
When bit value = 0
7
ADAPTER DETECT (FL80400 block)
ON (Lens adapter detect)
OFF
6-58
DCR-SR90E/SR100/SR100E_ADJ
7.
Lens Barrier Check
Page 6
Address 62
Note: Check that the data of page: 0, address: 10 is “00”.
Using method:
Order Page Address Data
Procedure
1
Set the unit to MOVIE mode
or STILL mode.
or STILL mode.
2
6
62
Check the data is “41”.
3
6
61
02
4
6
62
Check the data changes to
“82”.
“82”.
5
Check that the lens barrier is
closed.
closed.
6
6
61
01
7
6
62
Check the data is “41”.
8
Check that the lens barrier is
opened.
opened.
9
6
61
00
8.
G Sensor Check
Page 7
Address 95, 97, 99 to 9B
Note 1: Check that the data of page: 0, address: 10 is “00”.
Using method:
1) Place the camcorder in horizontal state.
2) Select page: 7, address: 95, 97 and 99 to 9B.
3) Read the displayed data and check that the data values are
1) Place the camcorder in horizontal state.
2) Select page: 7, address: 95, 97 and 99 to 9B.
3) Read the displayed data and check that the data values are
within respective specified values.
Note 2: For the address: 99 to 9B, the data values will vary de-
pending on how the camcorder is placed.
If the data values are out of the specified ranges, re-place
the camcorder correctly up to three times and if even once
the data values are within the specified values, the sen-
sor is normal.
If the data values are out of the specified ranges, re-place
the camcorder correctly up to three times and if even once
the data values are within the specified values, the sen-
sor is normal.
Address
95
97
99
9A
9B
Function
Data
(Specified value)
GSENS-REF (VC-449 board SE981)
70 to 8F
GSENS-TEMP (VC-449 board SE981)
68 to AE
GSENS-X (VC-449 board SE981)
94 to A3 (Note 2)
GSENS-Y (VC-449 board SE981)
76 to 86 (Note 2)
GSENS-Z (VC-449 board SE981)
76 to 86 (Note 2)
Click on the first or last page to see other DCR-SR100 / DCR-SR100E / DCR-SR90E (serv.man4) service manuals if exist.