DOWNLOAD Sony DCR-IP1 / DCR-IP1E (serv.man2) Service Manual ↓ Size: 8.33 MB | Pages: 80 in PDF or view online for FREE

1-5E

E

E

E

E

Block

Function

6

1

6

1

6

2

6

2

Detailed

Code

0

0

1

0

0

0

0

1

Symptom/State

Difficult to adjust focus
(Cannot initialize focus.)

Zoom operations fault
(Cannot initialize zoom lens.)

Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)

Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)

Self-diagnosis Code

Repaired b

y:

Correction

Inspect the lens block focus MR sensor (Pins qk, ql of CN5001 of
CD-458 board) when focusing is performed when the touch panel
is operated in the focus manual mode and the focus motor drive
signals (Pins 1, 2 of CN5001 of CD-458 board) when the focusing
is not performed.

Inspect the lens block zoom reset sensor (Pin qg  of CN5001 of
CD-458 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive signals (Pins wf  to  wj  of
CN5001 of CD-458 board) when zooming is not performed.

Inspect pitch angular velocity sensor (SE2702 of SE-139 board)
peripheral circuits.

Inspect yaw angular velocity sensor (SE2701 of SE-139  board)
peripheral circuits.

2-1

2-2

LCD

SERVICE POSITION

MECHANISM DECK

SERVICE POSITION

The following flow chart shows the disassembly procedure.

2-3

2-4

VC-333 board

IF-108 board

IF-108 board

FP-732 

flexible board

FP-722 

flexible board

Cabinet R block assembly

Lens block assembly

CN107 (No Mount)
CPC 

Mechanism deck

To eject the cassette, short the circuit between
 Pin 

0

 and between Pin 

qa

 (GND) pattern on

 IF-108 board of CN2604 for 1 second.

10

11

CN2604

AC power adaptor

AC IN

Adjustment remote commander
(RM-95)

To check the VTR section, set the VTR to the "Forced VTR power ON" mode.
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).

1)  Select page: 0, address: 01, and set data: 01.
2)  Select page: D, address: 10, set data: 02 and 

press the PAUSE button of the adjustment remote
commander.

Note: Although the following message is displayed when a power supply is switched on,

it is because the front panel is removed and this is normal.

Lens cover is not closed. Turn the power on again.

1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, data: 00, and press the PAUSE 

button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

Procedure of removing mechanism deck (Mechanism deck service position)

1

2-1.

Top cabinet assembly ............................................. (PAGE 2-5)

2

2-2.

F panel block assembly .......................................... (PAGE 2-5)

3

2-5.

Cabinet R block assembly ...................................... (PAGE 2-7)

4

2-6.

FP-732/FP-734 flexible board ................................. (PAGE 2-7)

5

2-10. IF-108 board ......................................................... (PAGE 2-11)

6

2-11. SE-139 board, Mic unit ......................................... (PAGE 2-11)

7

2-12. Lens block assembly ............................................ (PAGE 2-12)

8

2-14. Cabinet G ............................................................. (PAGE 2-13)

9

2-15. Cabinet L assembly .............................................. (PAGE 2-13)

q;

2-16. VC-333 board ....................................................... (PAGE 2-14)

qa

2-17. Mechanism deck ................................................... (PAGE 2-14)

ACX510CMN-J (LCD901)

PD-199 board

AC power adaptor

AC IN

Adjustment remote commander (RM-95)

2-5

 Follow the disassembly procedure in the numerical order given.

6

Two claws

5

7

Top cabinet assembly

4

Screw (M1.7)

2

Open the P cabinet block assembly.

3

Turn the P cabinet block assembly.

1

Screw (M1.7)

3

Screw (M1.7)

6

FP-731flexible board
(CN2602)

5

7

F panel block assembly

4

Screw (M1.7)

2

Screw (M1.7)

1

Close the P cabinet block assembly.