DOWNLOAD Sony DCR-IP1 / DCR-IP1E (serv.man2) Service Manual ↓ Size: 8.33 MB | Pages: 80 in PDF or view online for FREE

W100 MECHANISM

• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987626751.pdf).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL1 (987626741.pdf).
• For MECHANISM ADJUSTMENTS, refer to the “MICRO MV MECHANICAL ADJUSTMENT MANUAL 

2

 W MECHANISM  ” (9-876-276-11).

• Reference No. search on printed wiring boards is available.

• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
• TO TAKE OUT A CASSETE WHEN NOT EJECT (FORCE EJECT)

This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the CD-458 and VC-333 boards.
Therefore, schematic diagrams, printed wiring boards, mounted parts location and electrical parts list of the CD-458 and VC-
333 boards are not shown.
The following pages are not shown.

Schematic diagrams ........................... Pages 4-9 to 4-46
Printed wiring boards .......................... Pages 4-65 to 4-70

Mounted parts location .................. Pages 4-85 to 4-87
Electrical parts list ......................... Pages 5-14 and 5-18 to 5-26

US Model

Canadian Model

Korea Model

DCR-IP1

AEP Model

UK Model

East European Model

Chinese Model

Australian Model

Hong Kong Model

DCR-IP1E

E Model

Tourist Model

DCR-IP1/IP1E

— 2 —

Video recording system

2 rotary heads
Helical scanning system

Still image recording system

Exif Ver. 2.2*

Audio recording system

MPEG1 Audio Layer2
(Fs 48 kHz, stereo)

Video signal

PAL color, CCIR standards

Usable cassette

MICROMV cassette with the 

 

m

DCR-IP1:

DCR-IP1E:

NTSC color, EIA standards

ark printed

Tape speed

Approx. 5.66 mm/s

Recording/playback time (using an MGR60 
cassette)

Approx. 60 min

Fast forward/rewind time (using a MGR60 
cassette)

Approx. 1 min, and 30 s

Image device

3.6 mm (1/5.0 type) CCD (Charge 
Coupled Device)
Gross: Approx. 1 070 000 pixels
Effective (still): Approx. 1 000 000 
pixels
Effective (moving): Approx.  690 000 
pixels

Lens

Carl Zeiss Vario-Sonnar
Combined power zoom lens
10

 × (Optical), 120 × (Digital)

F = 1.8 ~ 2.3

Focal length

3.2 - 32 mm (5/32 - 1 5/16 in.)
When converted to a 35 mm still camera
In CAMERA-TAPE:
46 - 460 mm (1 13/16 - 18 1/8 in.)
In CAMERA-MEM:
38 - 380 mm (1 1/2 - 15 in.)

Color temperature

[AUTO], [HOLD], [INDOOR] (3 200 
K), [OUTDOOR] (5 800 K)

Minimum illumination

7 lx (lux) (F 1.8)

* Exif  is  a  file format for still images, established 

by the JEITA (Japan Electronics and 
Information Technology Industries 
Association). Files in this format can have 
additional information such as camera settings.

Audio/Video input/output

10-pin connector

Input/output auto switch
Video signal: 1 Vp-p, 75 

Ω (ohms),  

unbalanced, sync negative

Luminance signal: 1 Vp-p, 75 

Ω (ohms), 

 

unbalanced 
Chrominance signal: 

DCR-IP1: 0.286 Vp-p,
DCR-IP1E: 0.3 Vp-p,
75 

Ω (ohms), unbalanced

Audio signal: 327 mV, (at output 
impedance more than 47 k

Ω (kilohms))

Input impedance more than 47 k

Ω 

(kilohms)
Output impedance with less than 2.2 k

Ω  

(kilohms)

Picture

5.0 cm (2.0 type)

Total dot number

211 200 (960

 × 220)

Power requirements

DC 7.2 V (battery pack)
DC 8.4 V (AC Adaptor)

Average power consumption (when using the 
battery pack)

During camera recording using LCD 
with the normal brightness

3.8 W

Operating temperature

0 C to 40 C (32 F to 104 F)

Storage temperature

-20 C to + 60 C (-4 F to + 140 F)

Dimensions (approx.)

39 

× 91 × 69 mm (1 9/16 × 3 5/8 × 2 3/4 

in.) (w/h/d)

Mass (Approx.)

230 g (8 oz) main unit only
280 g (10 oz) including the NP-FF51 
rechargeable battery pack, MGR60 
cassette.

Supplied accessories

Audio/Video input/output

10-pin connector
Input/output auto switch
Video signal:1 Vp-p, 75 

Ω (ohms),  

unbalanced, sync negative 
Luminance signal: 1 Vp-p, 75 

Ω (ohms),  

unbalanced 

Audio signal: 327 mV, (at output 
impedance more than 47 k

Ω (kilohms))

Input impedance more than 47 k

Ω

 

 

(kilohms)
Output impedance with less than 2.2 k

Ω   

(kilohms)

USB jack

mini-B

i.LINK (MICROMV) input/output

4-pin connector S400

Power requirements

AC 100 - 240 V, 50/60 Hz

Current consumption

0.35 - 0.18 A

Power consumption

18 W

Output voltage

DC 8.4 V, 1.5 A

Operating temperature

0 C to 40 C (32 F to 104 F)

Storage temperature

-20 C to + 60 C (-4 F to + 140 F)

Dimensions (approx.)

56 

× 31 × 100 mm (2 1/4 × 1 1/4 × 4 in.) 

(w/h/d) excluding projecting parts

Mass (approx.)

190 g (6.7 oz) excluding the power cord 

Maximum output voltage

DC 8.4 V

Output voltage

DC 7.2 V

Capacity

5.6 Wh (780 mAh)

Operating temperature

0 C to 40 C (32 F to 104 F)

Dimensions (approx.)

40.8 

×  12.5 ×  49.1 mm (1 5/8 ×  1/2 × 1 

15/16 in.) (w/h/d)

Mass (approx.)

45 g (1.6 oz)

Type

Lithium ion

Design and specifications are subject to change 
without notice.

Memory Stick Duo adaptor (1)
AC Adaptor (1) 
Power cord (1)

Handycam Station DCRA-C100 (1)

Wireless Remote Commander (1)
A/V connecting cable (1)
USB cable (1)
Hand strap (1)
Rechargeable battery pack NP-FF51 (1)
Battery terminal cover (1)

MICROMV   (1)
Cleaning cloth (1) 
Camera Operations Guide (1) 
Computer Applications Guide (1) 
MovieShaker Applications Guide (1) 
21-pin adaptor (1) 
(AEP, UK, EE) 
2-pin conversion adaptor (1) 
(E, HK, JE) 
See page 5-27.

Chrominance signal: 

DCR-IP1: 0.286 Vp-p,
DCR-IP1E: 0.3 Vp-p,
75 

Ω (ohms), unbalanced

Memory Stick Duo   8MB (1)

CD-ROM   SPVD-010 USB Driver   (1) 
CD-ROM   MovieShaker Ver.3.1 for

• Abbreviation

AUS : Australian model
CH : Chinese model
CND : Canadian model
EE

: East European model

JE

: Tourist model

HK : Hong Kong model
KR

: Korean model

— 3 —

0

0

0

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

— 4 —

1-1.

Note for Repair ································································ 1-1

1-2.

Power Supply During Repairs ········································· 1-1

1-3.

To Take Out a Cassette when not Eject (Force Eject) ····· 1-2

1-4.

Self-diagnosis Function

1-4-1. Self-diagnosis Function ··················································· 1-3
1-4-2. Self-diagnosis Display ····················································· 1-3
1-4-3. Self-diagnosis Code Table ··············································· 1-4

Service Position: LCD Module ······································· 2-3
Service Position to Check the VTR Section ···················· 2-4

2-1.

Top Cabinet Assembly ····················································· 2-5

2-2.

F Panel Block Assembly ·················································· 2-5

2-3.

Gear With Motor (Lens Cover) (M904),
FP-731 Flexible Board ···················································· 2-6

2-4.

Lens Shutter, Lens Ornamental Plate ······························ 2-6

2-5.

Cabinet R Block Assembly ·············································· 2-7

2-6.

FP-732/FP-734 Flexible Board ······································· 2-7

2-7.

MS-153 Board ································································· 2-8

2-8.

PD-199 Board, LCD Module ·········································· 2-8

2-9.

Hinge Assembly, FP-733 Flexible Board ························ 2-9
Installation of FP-733 Flexible Board ··························· 2-10

2-10. IF-108 Board ································································· 2-11
2-11. SE-139 Board, Mic Unit ················································ 2-11
2-12. Lens Block Assembly ···················································· 2-12
2-13. CD-458 Board ······························································· 2-12
2-14. Cabinet G ······································································· 2-13
2-15. Cabinet L Assembly ······················································ 2-13
2-16. VC-333 Board ······························································· 2-14
2-17. Mechanism Deck ··························································· 2-14
2-18. Operation Switch Block (PW4720) ······························· 2-15
2-19. Grip Cover ····································································· 2-15
2-20. Circuit Boards Location ················································ 2-16
2-21. Flexible Boards Location ·············································· 2-17

3-1.

Overall Block Diagram (1/6) ··········································· 3-1

3-2.

Overall Block Diagram (2/6) ··········································· 3-3

3-3.

Overall Block Diagram (3/6) ··········································· 3-5

3-4.

Overall Block Diagram (4/6) ··········································· 3-7

3-5.

Overall Block Diagram (5/6) ··········································· 3-9

3-6.

Overall Block Diagram (6/6) ········································· 3-11

3-7.

Power Block Diagram (1/3) ··········································· 3-13

3-8.

Power Block Diagram (2/3) ··········································· 3-15

3-9.

Power Block Diagram (3/3) ··········································· 3-17

Section

Title

Page

Section

Title

Page

4-1.

Frame Schematic Diagrams
Frame Schematic Diagram (1/2) ····································· 4-1
Frame Schematic Diagram (2/2) ····································· 4-3

4-2.

Schematic Diagrams ························································ 4-5
FP-723 FLEXIBLE (CCD IMAGER) ····························· 4-7
PD-199 (LCD DRIVE) ·················································· 4-47
IF-108 (CRADLE TERMINAL) ··································· 4-49
MS-153 (MS CONNECTOR) ······································· 4-51
SE-139 (PITCH/YAW SENSOR) ·································· 4-53
DH-041, FP-080, FP-081, FP-228 FLEXIBLE ············· 4-55
FP-731, FP-769 FLEXIBLE ·········································· 4-56
FP-732, FP-733, FP-734 FLEXIBLE ···························· 4-57
CF4720, SS4720, PW4720
(CONTROL SWITCH BLOCK) ··································· 4-59

4-3.

Printed Wiring Boards ··················································· 4-63
PD-199 ··········································································· 4-71
IF-108 ············································································ 4-73
MS-153 ·········································································· 4-75
SE-139 ··········································································· 4-77
DH-041, FP-080, FP-081, FP-228 FLEXIBLE ············· 4-79
FP-731, FP-769 FLEXIBLE ·········································· 4-80
FP-732, FP-733, FP-734 FLEXIBLE ···························· 4-81

4-4.

Mounted Parts Location ················································ 4-88

5-1.

Exploded Views ···························································· 5-2

5-1-1. Overall Assembly ·························································· 5-2
5-1-2. F Panel Block Assembly ··············································· 5-3
5-1-3. Cabinet R Block Assembly-1 ········································ 5-4
5-1-4. Cabinet R Block Assembly-2 ········································ 5-5
5-1-5. Cabinet L Block Assembly-1 ········································ 5-6
5-1-6. Cabinet L Block Assembly-2 ········································ 5-7
5-1-7. Lens Block Assembly ··················································· 5-8
5-1-8. Mic Block Assembly ····················································· 5-9
5-1-9. MD Frame Block Assembly ······································· 5-10
5-1-10. Overall Mechanism Deck Section (W100) ················· 5-11
5-1-11. LS Chassis Block Assembly ······································· 5-12
5-1-12. Mechanism Chassis Block Assembly ························· 5-13
5-2.

Electrical Parts List ····················································· 5-14