Sony DCR-IP1 / DCR-IP1E (serv.man2) Service Manual ▷ View online
2-6
DCR-IP1/IP1E
2-3. GEAR WITH MOTOR (LENS COVER) (M904), FP-731 FLEXIBLE BOARD
2
Two screws (M1.7X3.5)
3
Connector
(CN7311)
(CN7311)
6
Gear with motor (Lens cover)
(M904)
(M904)
4
Two solders
5
FP-769 flexible board
1
Draw out the FP-769 flexible board
in a direction of the arrow.
At this time, take care not to damage
the flexible board.
in a direction of the arrow.
At this time, take care not to damage
the flexible board.
Note: When mounting the geared motor,
meet a convex portion of the gear with a
concave portion of the shutter lever.
concave portion of the shutter lever.
Shutter lever concave portion
Gear convex portion
8
Two screws (M1.7X3.5)
7
Screw
(M1.7X3.5)
(M1.7X3.5)
9
FP-731 flexible board
1
Screw (M1.7
X
3.5)
3
Shutter retainer
4
Shutter lever
5
Lens shutter
2
Screw (M1.7
X
3.5)
6
Two screws (M1.7
X
3.5)
7
Lens ornamental plate
2-4. LENS SHUTTER, LENS ORNAMENTAL PLATE
2-7
DCR-IP1/IP1E
2-6. FP-732/FP-734 FLEXIBLE BOARD
3
Screw (M1.7)
2
Screw (M1.7
X
2.5)
1
Open the P cabinet block assembly.
4
Two screws
(M1.7
(M1.7
X
2.5)
7
FP-732 flexible board
(CN2605)
(CN2605)
6
Paying attention to the FP-732 flexible board,
raise the cabinet R block assembly a little.
raise the cabinet R block assembly a little.
9
Cabinet R block assembly
8
FP-720 flexible board
(CN109)
(CN109)
5
Close the P cabinet block assembly.
Note: Pell of the flexible board a little by little,
not applying an excessive force,
as it is adhered strongly with the panel sheet.
as it is adhered strongly with the panel sheet.
7
Two solders
8
Lithium battery (secondary)
5
Two claws
qa
FP-734 flexible board
4
SP retainer assembly
6
Flexible board
(CN2904)
(CN2904)
2
FP-733 flexible board (CN2903)
q;
Loud speaker (1.6cm)
9
Two solders
1
Panel sheet
qj
FP-732 flexible board
qh
Battery terminal board
(BT901)
(BT901)
qf
qg
Six solders
qd
Three screws (M1.7
X
4)
qs
Open the jack cover assembly.
3
Two screws (M1.7
X
2.5)
2-5. CABINET R BLOCK ASSEMBLY
2-8
DCR-IP1/IP1E
2-7. MS-153 BOARD
2
Screw (M1.7
X
2.5)
1
MS sheet
6
MS-153 board
5
FP-720 flexible board (CN2902)
3
Paying attention to the
operation switch block,
remove two convex portions
of the board.
operation switch block,
remove two convex portions
of the board.
4
Control switch block (CF4720)
(CN2901)
(CN2901)
Control switch block
(CF4720)
(CF4720)
1
9
FP-733 flexible board
(CN3501)
(CN3501)
3
Screw (M1.7
X
4)
8
Screw
(M1.7
(M1.7
X
2.5)
q;
P cabinet L block
5
Screw (M1.7
X
4)
6
Two claws
7
P cabinet R assembly
2
4
qs
Flexible board
(CN3504)
(CN3504)
qd
Flexible board
(CN3502)
(CN3502)
qf
Flexible board
(CN3503)
(CN3503)
ws
Panel lock retainer
wd
LCD module
wf
P cushion
qk
PD-199 board
qh
qg
Claw
qa
Screw
(M1.7
(M1.7
X
2.5)
wh
P cabinet L
w;
Two claws
wa
LCD fixed plate
ql
Screw
(M1.7
(M1.7
X
2.5)
qj
PD sheet
wg
Light interception sheet
2-8. PD-199 BOARD, LCD MODULE
2-9
DCR-IP1/IP1E
2-9. HINGE ASSEMBLY, FP-733 FLEXIBLE BOARD
A
1
4
Two claws
qg
Four claws
7
Two claws
9
Magnet
5
Hinge cover (front)
8
Hinge cover (rear)
3
Paying attention to the
FP-733 flexible board,
remove the hinge assembly.
FP-733 flexible board,
remove the hinge assembly.
0
Remove an H-shaped part of the
FP-733 flexible board from the hinge assembly.
FP-733 flexible board from the hinge assembly.
qj
FP-733 flexible board
qa
Rotate the FP-733 flexible board
in the arrow
in the arrow
A
direction to remove,
which winds around the hinge assembly.
qs
Remove the flexible clamper
from the hinge assembly.
from the hinge assembly.
qf
Remove the IC7301 part
from the flexible clamp.
from the flexible clamp.
qh
Flexible clamp
2
Two screws
(M1.7
(M1.7
X
4)
6
Screw (M1.7
X
4)
qd
Hinge assembly
Click on the first or last page to see other DCR-IP1 / DCR-IP1E (serv.man2) service manuals if exist.