Sony DCR-HC90 / DCR-HC90E (serv.man4) Service Manual ▷ View online
6-6
DCR-HC90/HC90E
Fig. 6-1-3.
7
5
3
2
2
6
4
1
3
4
1
3
CPC lid
AC power
adaptor
adaptor
AC IN
Adjustment remote
commander (RM-95)
commander (RM-95)
LANC jack
DC-IN connector
8
1
I/F unit for LANC control
(J-6082-521-A)
(J-6082-521-A)
CPC-15
(J-6082-564-A)
(J-6082-564-A)
*1
*1
*1: Don’t connect any cable
to these connectors.
For tape path adjustment
1
RF MON
2
SWP
3
GND
4
XSC EEP
5
EEP SCK
6
EEP SO
7
EEP SI
[CONNECTION OF EQUIPMENT]
CN002
CN001
BATT
LANC
Not used
Not used
Not used.
Not used
6-7
DCR-HC90/HC90E
White
Black
841mm
1189mm
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1.
POWER switch (SS11600 block) ............... CAMERA-TAPE
2.
NIGHT SHOT switch (Lens block) ................................. OFF
3
WIDE (4:3/16:9) ................................................................ 4:3
4.
BACK LIGHT switch (EZ11600 block) .......................... OFF
5.
MENU settings (Touch panel)
CAMERA SET menu
CAMERA SET menu
PROGRAM AE .................................................... AUTO
SPOT METER ...................................................... AUTO
EXPOSURE ......................................................... AUTO
WHITE BALANCE ............................................. AUTO
AE SHIFT ..................................................................... 0
SPOT METER ...................................................... AUTO
EXPOSURE ......................................................... AUTO
WHITE BALANCE ............................................. AUTO
AE SHIFT ..................................................................... 0
FOCUS .......................................................... MANUAL
TELE MACRO ......................................................... OFF
COLOR SLOW SHUTTER ..................................... OFF
ZEBRA ..................................................................... OFF
DIGITAL ZOOM ..................................................... OFF
STEADY SHOT ....................................................... OFF
TELE MACRO ......................................................... OFF
COLOR SLOW SHUTTER ..................................... OFF
ZEBRA ..................................................................... OFF
DIGITAL ZOOM ..................................................... OFF
STEADY SHOT ....................................................... OFF
PICT. APPLI menu
DIGITAL EFECT ..................................................... OFF
PICTURE EFECT .................................................... OFF
DEMO MODE ......................................................... OFF
PICTURE EFECT .................................................... OFF
DEMO MODE ......................................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig. 6-1-4.
3. Subjects
1)
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2)
Mixed color compensation chart (Color reproduction
adjustment frame)
Remove the color bar chart from the pattern box and insert a
mixed color compensation chart in its place. (Do not perform
zoom operations during this time.)
adjustment frame)
Remove the color bar chart from the pattern box and insert a
mixed color compensation chart in its place. (Do not perform
zoom operations during this time.)
3)
Clear chart (All white frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. Then adjust the zoom to TELE side
from WIDE side, and stop it when the black frame of the chart
disappears.
Remove the color bar chart from the pattern box and insert a
clear chart in its place. Then adjust the zoom to TELE side
from WIDE side, and stop it when the black frame of the chart
disappears.
4)
Flange back adjustment chart
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
Fig. 6-1-5.
Note: Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
6-8
DCR-HC90/HC90E
4. Preparing the Flash Adjustment Box
A dark room is required to provide an accurate strobe adjustment.
If it is not available, prepare the flash adjustment box as given below;
A dark room is required to provide an accurate strobe adjustment.
If it is not available, prepare the flash adjustment box as given below;
1) Provide woody board A, B and C of 15 mm thickness.
woody board A (2 sheets)
400 mm
woody board B (2 sheets)
370 mm
woody board C (1 sheet)
700 mm
513 mm
513 mm
700 mm
700 mm
730 mm
2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side
of woody board A, B and C are internal. (Fig. 6-1-7)
Fig. 6-1-6.
woody board A
woody board B
woody board B
woody board C
woody board A
Fig. 6-1-7.
6-9
DCR-HC90/HC90E
1-2.
INITIALIZATION OF 8, A, B, C, D, E, F, 14, 18,
19, 1A, 1B, 1C, 1E, 1F PAGE DATA
19, 1A, 1B, 1C, 1E, 1F PAGE DATA
Note: When reading or writing the 14, 18, 19, 1A, 1B, 1C, 1E or 1F page
data, select page: 0, address: 10, and set data: 01, then select 4, 8, 9,
A, B, C, E or F page. The 14, 18, 19, 1A, 1B, 1C 1E, or 1F page can
be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
A, B, C, E or F page. The 14, 18, 19, 1A, 1B, 1C 1E, or 1F page can
be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1-2-1.
INITIALIZATION OF A, B, D, 1A, 1B PAGE DATA
Note: When reading or writing the A, B, D page data, select page: 0,
address: 10, and set data: 00.
When reading or writing the 1A or 1B page data, select page: 0,
address: 10, and set data: 01, then select A or B page. The 1A or 1B
page can be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
When reading or writing the 1A or 1B page data, select page: 0,
address: 10, and set data: 01, then select A or B page. The 1A or 1B
page can be chosen by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1. Initializing the A, B, D, 1A, 1B Page Data
Note1: If the A, B, D, 1A, 1B page data has been initialized, the following
adjustments need to be performed again.
1) Modification of A, B, D, 1A, 1B page data
2) Touch panel adjustment
1) Modification of A, B, D, 1A, 1B page data
2) Touch panel adjustment
Adjusting page
A
Adjusting Address
10 to FF
Adjusting page
B
Adjusting Address
00 to FF
Adjusting page
D
Adjusting Address
10 to 7F
Adjusting page
1A
Adjusting Address
00 to FF
Adjusting page
1B
Adjusting Address
00 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
0
10
00
Set the data.
3
7
04
Set the following data.
50 (DCR-HC90 (NTSC))
51 (DCR-HC90E (PAL))
50 (DCR-HC90 (NTSC))
51 (DCR-HC90E (PAL))
4
7
01
XX
Set the data. (Note2)
5
7
00
01
Set the data, and press PAUSE
button. (Note)
button. (Note)
6
7
02
Check that the data changes to
“01”
“01”
7
Perform “Modification of A, B,
D, 1A, 1B Page Data”.
D, 1A, 1B Page Data”.
Note2: XX=20: Initializing A page
XX=21: Initializing B page
XX=22: Initializing D page
XX=23: Initializing 1A page
XX=24: Initializing 1B page
XX=25: Initializing A and 1A page
XX=26: Initializing B and 1B page
XX=28: Initializing A, B, D, 1A and 1B pages
XX=22: Initializing D page
XX=23: Initializing 1A page
XX=24: Initializing 1B page
XX=25: Initializing A and 1A page
XX=26: Initializing B and 1B page
XX=28: Initializing A, B, D, 1A and 1B pages
2. Modification of A, B, D, 1A, 1B Page Data
If the A, B, D, 1A, 1B page data has been initialized, change the
data of the “Fixed data-2” address shown in the following tables by
manual input.
If the A, B, D, 1A, 1B page data has been initialized, change the
data of the “Fixed data-2” address shown in the following tables by
manual input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
When changing the A, B, D page data, select page: 0, address:
10, and set data: 00.
10, and set data: 00.
3)
When changing the 1A, 1B page data, select page: 0, address:
10, and set data: 01.
After completing the modification of 1A, 1B page data, reset
the data of this address to “00”.
10, and set data: 01.
After completing the modification of 1A, 1B page data, reset
the data of this address to “00”.
4)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
5)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Processing after Completing Modification of A, B, D, 1A, 1B Page data
Order Page Address Data
Procedure
1
0
10
00
Set the data.
2
2
00
29
Set the data.
3
2
01
29
Set the data, and press PAUSE
button.
button.
Note: If the following symptoms occur after completing of the
“Modification of A, B, D, 1A, 1B page data”, check that the data of
addresses: 1A to 4F of A page and the data of addresses: 12 to 19 of
D page are same as those of the same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.
addresses: 1A to 4F of A page and the data of addresses: 12 to 19 of
D page are same as those of the same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.
Click on the first or last page to see other DCR-HC90 / DCR-HC90E (serv.man4) service manuals if exist.