Sony DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) Service Manual ▷ View online
1-16E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
1-6-2. 機銘板(シート)の有るセット(ブラジル向けモデル)
キャビL部組交換後は,機銘板(シート)の貼替えを行なってください。
HDR-UX20 (CND
仕向
)
A-1504-778-A
部品コード
部 品 名
サ-ビス用 キャビ L 部組 (20-CA)
シリアルナンバー
HDR-UX20 (E, JE
仕向
)
A-1504-779-A
部品コード
部 品 名
サ-ビス用 キャビ L 部組 (20-E23)
シリアルナンバー
HDR-UX20 (KR
仕向
)
A-1504-780-A
部品コード
部 品 名
サ-ビス用 キャビ L 部組 (20-KR)
シリアルナンバー
HDR-UX20E (NE
仕向
)
A-1504-781-A
部品コード
部 品 名
サ-ビス用 キャビ L 部組 (20E-CE)
シリアルナンバー
HDR-UX20E (E, HK, AUS, JE
仕向
)
A-1504-782-A
部品コード
部 品 名
サ-ビス用 キャビ L 部組 (20E-E35)
シリアルナンバー
X-2188-907-1
キャビ L 組立 (DCR-DVD910: BR)
部品コード
部 品 名
1-6-3. 日本向けモデルのキャビL部組交換時の注意
交換前のキャビL 部組に印字されている“製造年(下図の○部の表示)”と同じ表示のラベルを新しいキャビL 部組に貼付け
てください。
例:下図では,“07年製”のラベルを貼る
てください。
例:下図では,“07年製”のラベルを貼る
* ラベルは,サービス用キャビL部組に「投げ込み(ラベル貼り方)」を含めて同梱されています。
1-6-4. 韓国向けモデルのキャビL部組交換時の注意
交換前のキャビL 部組に印字されている“製造年月(下図の○部の表示)”と同じ表示のラベルを新しいキャビL 部組に貼付
けてください。
例:下図では,“2007.5”のラベルを貼る
けてください。
例:下図では,“2007.5”のラベルを貼る
* ラベルは,サービス用キャビL部組に「投げ込み(ラベル貼り方)」を含めて同梱されています。
*
ラベルを貼付けてください
*
製造年
*
ラベルを貼付けてください
*
製造年月
2-1
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF ST-183 BOARD’S CHARGING CAPACITOR (C5006)
The charging capacitor (C5006) of ST-183 board is charged up
to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
1 k
Ω
/1 W
Wrap insulating tape.
NOTE FOR DISCONNECTING THE HARNESS (HN-048)
When disconnecting the harness (HN-048), do not pull the
harness part but pull off the connector body with tweezers etc.
harness part but pull off the connector body with tweezers etc.
Harness
(HN-048)
(HN-048)
Tweezers etc.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
Short-circuit between the two points
with the short jig about 10 seconds.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
ST-183 Board
- Bottom View -
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
2. DISASSEMBLY
2-2
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
2-2-1. OVERALL SECTION
⋅
Cabinet (L (Upper))
⋅
Cabinet (R)
2-2-3. SHOE COVER SECTION
⋅
Cabinet (Top)
2-2-2. CABINET (R) SECTION
⋅
LCD Block
⋅
Hinge Block
2-2-4. MIDWAY FRAME SECTION
⋅
Front Panel
⋅
Midway Frame Block
2-2-5. SHOE FRAME SECTION
⋅
Shoe Frame Block
⋅
BT/EVF Block
2-2-6. CM HEAT SINK SECTION
⋅
Cabinet (L)
⋅
CM Heat Sink
2-2-7. MAIN BOARD SECTION
⋅
VC-521 Board
⋅
LD-233 Board
2-2-8. LENS/MD Section
⋅
Lens Block
⋅
MD Block
⋅
Flash Block
- DISASSEMBLY FLOW -
LCD Block
⋅
FP-386 Flexible Board
⋅
PD-353 Board
Flash Unit
P Cabinet
Cabinet (R)
⋅
CK-193 Board
⋅
OC-013 Board
Hinge Block
⋅
FP-833 Flexible Board
Lens Block
⋅
CMOS Block (CM-093 Board)
LD-233 Board
⋅
FP-837 Flexible Board
VC-521 Board
BT/EVF Block
⋅
BL-023 Board
⋅
JK-363 Board
⋅
FP-836 Flexible Board
Shoe Frame
⋅
FP-835 Flexible Board
⋅
SW-523 Board
Front Panel
⋅
FP-832 Flexible Board
⋅
FR-283 Board
Midway Frame
⋅
FP-834 Flexible Board
⋅
MS-393 Board
⋅
ST-183 Board
MD Block
Cabinet (L)
Cabinet (Top)
CM Heat Sink
Main Frame
2-1. IDENTIFYING PARTS
2-3
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
2-2. DISASSEMBLY
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1
Cabinet (L (Upper)) (
1
-1 to
1
-8)
2
Cabinet (R) (
2
-1 to
2
-8)
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
Shoe Cover
Section
Section
(See page 2-5)
1
Cabinet (L (Upper))
1
-1 (#2)
1
-4 (#2)
1
-8 (#11)
1
-3
2
Cabinet (R)
(See page 2-4)
2
-2 (Open)
2
-3 (#10)
2
-5 (#3)
2
-6 (#2)
2
-7 (#2)
2
-1
2
-8
1
-2
(Claw)
1
-5 (Claw)
1
-6
1
-7 (Open)
2
-4
Refer to page 1-1 “1-2. To take out
a disc when not eject (force eject)".
a disc when not eject (force eject)".
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
Short-circuit between the two points
with the short jig about 10 seconds.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
ST-183 Board
- Bottom View -
Click on the first or last page to see other DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) service manuals if exist.