Sony DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) Service Manual ▷ View online
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
1-5. METHOD OF COPING WITH SHIFT LENS ERROR
about 330 msec
Fig. 1
Measurement points on the LD-233 board
IC5501
LD-233 BOARD
R5526
R5534
R5549
R5549: No Mount
(Short Land)
Fig. 2
Change in output voltage of R5549 on the LD-233 board
Note: The length of low section will vary a little depending on the
conditions.
1-5-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501 on the LD-233 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1301 of VC-521 board) periphery.
the camera control circuit (IC1301 of VC-521 board) periphery.
Note:
When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
IC1301
VC-521 BOARD (SIDE A)
Fig. 3
Measurement points on the VC-521 board
Ver. 1.1 2008.02
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
Address
7430
F946
F948
F948
F946
F948
F948
7430
1-5-2. E:62:11 [Shift Lens Overheating (Pinch)] Occurred
Connect by the SeusEX and perform the following process.
Order
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Block
11
11
11
11
11
11
11
11
Page
80
8E
8E
8E
8E
8E
8E
80
Procedure
Write the data. (After it starts, set it before caution is displayed.)
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5526 in
the periphery of IC5501 on the LD-233 board to check the output voltage varies.
the periphery of IC5501 on the LD-233 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
varied, proceed to the order 12.
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
on the LD-233 board, turn the power ON to check that the output voltage immediately after
the power on change as shown in Fig. 2.
on the LD-233 board, turn the power ON to check that the output voltage immediately after
the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-521 board) periphery.
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-521 board) periphery.
Note 1:
Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address: F948, data: 00, and then retry.
Note 2:
When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Data
01
F0
01
00
10
01
00
00
1-6
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
Address
7430
F947
F949
F949
F947
F949
F949
7430
1-5-3. E:62:12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Block
11
11
11
11
11
11
11
11
Page
80
8E
8E
8E
8E
8E
8E
80
Procedure
Write the data. (After it starts, set it before caution is displayed.)
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5534 in
the periphery of IC5501 on the LD-233 board to check the output voltage varies.
the periphery of IC5501 on the LD-233 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
varied, proceed to the order 12.
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
on the LD-233 board, turn the power ON to check that the output voltage immediately after
the power on change as shown in Fig. 2.
on the LD-233 board, turn the power ON to check that the output voltage immediately after
the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-521 board) periphery.
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-521 board) periphery.
Note 1:
Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address: F949, data: 00, and then retry.
Note 2:
When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Data
01
F0
01
00
10
01
00
00
1-5-4. E:62:20 [Abnormality of Thermistor] Occurred
Order
1
2
3
Procedure
Turn the power ON
Confirm the connections of fkexible flat cables and connectors between the lens block and LD-233 board, LD-233 board and
VC-521 board.
VC-521 board.
In case of no malfunction of connections, replace the lens block with new one (Note). When the error has occurred in spite of the
lens replacement, replace LD-233 board with new one.
lens replacement, replace LD-233 board with new one.
Note:
When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-7
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
1-6-1. Laser Printed Unit
The model display adopts the laser printing method.
Therefore, the Cabinet (L) Block Assy for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
Therefore, the Cabinet (L) Block Assy for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note:
After replacing the Cabinet (L) Block Assy, the serial number
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
for it will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
1-6. PRECAUTION ON REPLACING THE CABINET (L) BLOCK ASSY
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
DCR-DVD510E (AEP, EE)
A-1504-766-A CABINET (L) BLOCK ASSY
(DVD510)
DCR-DVD910 (US)
A-1504-767-A CABINET (L) BLOCK ASSY
(910-U)
DCR-DVD910 (E)
A-1504-768-A CABINET (L) BLOCK ASSY
(910-E33)
DCR-DVD910E (NE)
A-1504-769-A CABINET (L) BLOCK ASSY
(910E-CE)
DCR-DVD910E (E)
A-1504-770-A CABINET (L) BLOCK ASSY
(910E-E3)
HDR-UX9E (AEP)
A-1504-771-A CABINET (L) BLOCK ASSY
(UX9E)
HDR-UX10 (US)
A-1504-772-A CABINET (L) BLOCK ASSY
(UX10)
HDR-UX10E (NE)
A-1504-773-A CABINET (L) BLOCK ASSY
(10E-CE)
HDR-UX10E (E)
A-1504-774-A CABINET (L) BLOCK ASSY
(10E-E35)
HDR-UX19E (AEP)
A-1504-775-A CABINET (L) BLOCK ASSY
(UX19E)
HDR-UX20 (J)
A-1504-776-A CABINET (L) BLOCK ASSY
(20-J)
HDR-UX20 (US)
A-1504-777-A CABINET (L) BLOCK ASSY
(20-U)
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Part No.
Description
Click on the first or last page to see other DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) service manuals if exist.