Sony DCR-DVD301 (serv.man4) Service Manual ▷ View online
6-7
DCR-DVD301
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
Unless otherwise specified, set the switches as follows and perform
adjustments without loading cassette.
1.
MODE dial (PS8700 block) ............................ MOVIE (
)
2.
NIGHT SHOT (Lens block) ............................................ OFF
3.
COLOR SLOW S/ SUPER NS (PS8700 block) .............. OFF
4.
FOCUS (SH8700 block) ....................................... MANUAL
5.
BACK LIGHT (JS-031 board) ......................................... OFF
6.
STEADY SHOT (Menu setting) ...................................... OFF
7.
DIGITAL ZOOM (Menu setting) .................................... OFF
8.
DEMO MODE (Menu setting) ........................................ OFF
9.
PROGRAM AE (Menu setting) ................................... AUTO
10. PICTURE EFECT (Menu setting) ................................... OFF
11. DIGITAL EFECT (Menu setting) .................................... OFF
12. WHITE BALANCE (Menu setting) ............................ AUTO
13. 16:9 WIDE (Menu setting) .............................................. OFF
11. DIGITAL EFECT (Menu setting) .................................... OFF
12. WHITE BALANCE (Menu setting) ............................ AUTO
13. 16:9 WIDE (Menu setting) .............................................. OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Basically carry out adjustments in the order given.
Fig. 6-1-4.
3. Subjects
1)
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Then adjust the zoom to TELE side
from WIDE side, and stop it when the black frame of the chart
disappears.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Then adjust the zoom to TELE side
from WIDE side, and stop it when the black frame of the chart
disappears.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
Fig. 6-1-5.
Note: Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
White
Black
841mm
1189mm
6-8
DCR-DVD301
1-2.
INITIALIZATION OF A, B, C, D, E, F, 14, 19,
1B, 1E, 1F PAGE DATA
1B, 1E, 1F PAGE DATA
Note: When reading or writing the 14, 19, 1B, 1E, 1F page data, select
page: 0, address: 10, and set data: 01, then select 4, 9, B, E or F
page. The 14, 19, 1B, 1E or 1F page can be chosen by this data
setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
page. The 14, 19, 1B, 1E or 1F page can be chosen by this data
setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1-2-1.
INITIALIZATION OF A, B, C, D, 1B PAGE DATA
Note: When reading or writing the A, B, C, D page data, select page: 0,
address: 10, and set data: 00.
When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
1. Initializing the A, B, C, D, 1B Page Data
Note1: Reading/writing the C page data by using the
is
impossible.
Note2: If the B page data has been initialized, the following adjustments
need to be performed again.
1) Viewfinder system adjustments
2) LCD system adjustments
3) Video system adjustments
1) Viewfinder system adjustments
2) LCD system adjustments
3) Video system adjustments
Adjusting page
A
Adjusting Address
10 to FF
Adjusting page
B
Adjusting Address
30 to FF
Adjusting page
C
Adjusting Address
10 to FF
Adjusting page
D
Adjusting Address
10 to 76
Adjusting page
1B
Adjusting Address
10 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data.
2
0
10
00
Set the data.
3
7
02
00
Set the data.
4
7
03
01
Set the data.
5
7
00
XX
Set the data. (Note4)
6
7
01
XX
Set the data, and press PAUSE
button. (Note4)
button. (Note4)
7
7
02
Check that the data changes to
“01”
“01”
Perform “Modification of A, B, C,
D, 1B Page Data”.
D, 1B Page Data”.
Note4: XX=20: Initializing A page
XX=21: Initializing B page
XX=22: Initializing 1B page
XX=23: Initializing D page
XX=24: Initializing C page
XX=28: Initializing A, B, C, D and 1B page
XX=22: Initializing 1B page
XX=23: Initializing D page
XX=24: Initializing C page
XX=28: Initializing A, B, C, D and 1B page
2. Modification of A, B, C, D, 1B Page Data
If the A, B, C, D or 1B page data has been initialized, change the
data of the “Fixed data-2” address of the initialized page shown in
the following tables by manual input.
If the A, B, C, D or 1B page data has been initialized, change the
data of the “Fixed data-2” address of the initialized page shown in
the following tables by manual input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
When changing the A, B, C, D page data, select page: 0, address:
10, and set data: 00.
10, and set data: 00.
3)
When changing the 1B page data, select page: 0, address: 10,
and set data: 01.
After completing the modification of 1B page data, reset the
data of this address to “00”.
and set data: 01.
After completing the modification of 1B page data, reset the
data of this address to “00”.
4)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
5) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
data to write the data in the non-volatile memory.
Processing after Completing Modification of A, B, C, D, 1B Page data
Order Page Address Data
Procedure
1
0
01
00
Set the data.
2
Turn off the power and turn on
again.
again.
Note: If the following symptoms occur after completing of the
“Modification of A, B, C, D, 1B page data”, check that the data of
addresses: 1A to 4F of A page and the data of addresses: 12 to 19 of
D page are same as those of the same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.
addresses: 1A to 4F of A page and the data of addresses: 12 to 19 of
D page are same as those of the same model of the same destination.
1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.
2) The power is shut off so that unit cannot operate.
6-9
DCR-DVD301
3. A Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
C, D, 1B Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Table. 6-1-2.
4. B Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
C, D, 1B Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Address
Remark
00 to 0F
10 to 17
18
19 to 69
6A
6B to E6
E7
E8 to FF
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Table. 6-1-3.
00 to 2F
30
31
32
33 to 3E
3F
40
41 to 44
45
46
47
48 to 4F
50
51
52
53 to 55
56
57
58
59 to 7A
7B
7C
7D to D0
D1
D2
D3
D4 to FF
6C
90
8D
78
3E
6C
90
BC
78
77
5C
87
98
88
9A
6E
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
VCO adj. (EVF)
Fixed data-1
White balance adj. (EVF)
Contrast adj. (EVF)
Fixed data-1
VCO adj. (LCD)
V COM adj. (LCD)
Fixed data-1
Transmissive mode white balance
adj. (LCD)
Contrast adj. (LCD)
Fixed data-1
Reflective mode white balance adj.
(LCD)
Fixed data-1
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Fixed data-1
Address
Remark
Initial value
6-10
DCR-DVD301
5. C Page Table
Note1: Reading/writing the C page data by using the
is
impossible.
Note2: The data of page: 0, address: 10 must be “00”.
Note3: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
Note3: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
C, D, 1B Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Table. 6-1-4.
6. D Page Table
Note1: The data of page: 0, address: 10 must be “00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
C, D, 1B Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Address
Remark
00 to 0F
10 to FF Fixed data-1
Table. 6-1-5.
7. 1B Page Table
Note1: When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1E page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, B,
C, D, 1B Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
Fixed data-2: Modified data. (Refer to “2. Modification of A, B,
C, D, 1B Page Data”).
00 to 0F
10
11
12
13
14
15
16
17
18
19
20 to 21
22
23
24
25
26
27 to 29
2A
2B
2C to 2D
2E
2F to 35
36
37
38
39
3A
3B to 57
58
56 to 76
00
Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Address
Remark
Initial value
Table. 6-1-6.
Address
Remark
00 to 0F
10 to FF Fixed data-1
Click on the first or last page to see other DCR-DVD301 (serv.man4) service manuals if exist.