DOWNLOAD Sony CCD-TR913E / CCD-TR950E Service Manual ↓ Size: 33.08 MB | Pages: 127 in PDF or view online for FREE

5-41

Adjust using a IR receiver jig (J-6082-383-A).

If the distance between the IR receiver jig and the camcorder is
below 1m, cover the LASER LINK emitter with a ND filter. (For
example, when the distance is 30cm to 50cm, cover the LASER
LINK emitter with a ND filter 1.0.)

LASER LINK ........................................ ON (Red LED is lit)

Mode

Camera standby

Subject

Arbitrary

Measurement Point

Pin 5 of CN003 of IR receiver jig (RF)
(Or Pin !§ of IC751 of VC-214 board)

Measuring Instrument

Frequency counter

Adjustment Page

F

Adjustment Address

68

Specified Value

f = 11.85 ± 0.05 MHz

Connection of Equipment
Connect the measuring device as shown in the following figure,
and adjust.

Fig. 5-3-15.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 01, set data: 37, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: F, address: 68, change the data, and set the video
carrier frequency (f) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 2, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.

6)

Select page: 0, address: 01, and set data: 00.

Mode

Camera standby

Subject

Arbitrary

Measurement Point

VIDEO OUT terminal of IR receiver jig
(Terminated at 75

Ω

)

Measuring Instrument

Oscilloscope

Adjustment Page

F

Adjustment Address

66

Specified Value

A = 0.87 ± 0.04 V

Connection of Equipment
Connect the measuring device as shown in the following figure,
and adjust.

Fig. 5-3-16.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 01, set data: 39, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: F, address: 66, and change the data, set the video
signal amplitude (A) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 2, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.

6)

Select page: 0, address: 01, and set data: 00.

Main unit

IR receiver jig

Pin 

5

 of 

CN003

Frequency counter

Main unit

IR receiver jig

VIDEO

OUT

75

Ω

75

Ω

 (1-247-804-11)

Oscilloscope

A

H

Fig. 5-3-17.

5-42

(75

Ω

)

600

Ω

Video

L

R

Audio

AUDIO OUT

L

47k

Ω

47k

Ω

 (1-249-437-11)

600

Ω

 

(270

Ω

 (1-249-410-11) + 330

Ω

 

(1-249-411-11))

Pattern generator

Audio oscillator

Main unit

Attenuator

Audio level meter

VIDEO OUT

R

IR receiver jig

Fig. 5-3-18.

Mode

VTR recording

Signal

Audio signal :
400Hz, –7.5dBs : L or R of AUDIO

terminal

Video signal :
Color bar signal : VIDEO terminal

Measurement Point

AUDIO L terminal and AUDIO R
terminal of IR receiver jig
(Terminated at 47k

Ω

)

Measuring Instrument

Audio level meter

Adjustment Page

F

Adjustment Address

67

Specified Value

Signal level: –7.5 ± 2.0 dBs
Level difference of L and R: Below 2dB

Connection of Equipment
Connect the measuring device as shown in the following figure,
and adjust.

Preparations only for the model without REC switch:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 14, after memorizing the data, set the
bit value of bit1 to “1”. (Refer to “4-3, 3. Bit value
discrimination” of “5-4. Service Mode”).

3)

Select page: D, address: 15, after memorizing the data, set the
bit value of bit7 to “0”.

4)

Insert a tape, and set to recording mode. (Use the wireless
remote commander of 8mm VCR.)

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Connect the audio level meter to the AUDIO L terminal of the
IR receiver jig.

3)

Select page: F, address: 67, change the data and set the 400Hz
audio signal level to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Connect the audio level meter to the AUDIO R terminal of the
IR receiver jig.

6)

Check that the 400Hz audio signal level is within the specified
value. If outside, repeat from step 2).

7)

Select page: 0, address: 01, and set data: 00.

Processing after completed adjustment only for the model
without REC switch:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 14, and set the data memorized at step
2) of “Preparations only for the model without REC switch”.

3)

Press the PAUSE button of the adjustment remote commander.

4)

Select page: D, address: 15, and set the data memorized at step
3) of “Preparations only for the model without REC switch”.

5)

Press the PAUSE button.

6)

Select page: 0, address: 01, and set data: 00.

5-43

• Perform the adjustment using color bar signal as a video signal

input for the VIDEO terminal.

• The items to be adjusted for the R channel will be indicated within

the [ ], in regard to the adjusting items to be adjusted for both L
and R channels.

• Set the Hi-Fi sound switch in the menu display to “STEREO”

position unless specified otherwise.

1) When inputting the audio signal, input same signal to both the L and R

channels, unless otherwise.

2) Be sure insert the plug (Shorting plug or dummy plug, etc) into the

AUDIO terminal (Right). If the plug is not inserted, the monaural mode
will be set, and correct adjustments can not be carried out.

During recording ............... REC AFM RF 1.7MHz carrier will not be

output.

During playback ................ The L + R signal will be output from the

AUDIO terminal (Left).

Connect the audio system measuring instruments in addition to the
video system measuring instruments as shown in Fig. 5-3-19, and
perform adjustments at the power switch [PLAYER] position.

1)

1.5MHz deviation adjustment

2)

1.7MHz deviation adjustment

3)

BPF f

0 

adjustment

Pattern generator

Video output

(75 

Ω

)

Audio
oscillator

Attenuator

600 

Ω

600 

Ω

 (270 

Ω

 (1-249-410-11) +330 

Ω

 (1-249-411-11))

Main unit

Main unit

VIDEO

VIDEO

AUDIO

AUDIO

L

R

L

R

L

R

47k 

Ω

47k 

Ω

 :1-249-437-11

47k 

Ω

 :1-249-437-11

Audio level meter or
distortion meter

TV monitor

Oscilloscope

TP27
(GND)

TP28(DC)

CH1

B

INV

A

SIN

8 0 !¡

AFM DEV jig 
(J-6082-312-A)

TP33(GND)
TP32(R OUT 1) 

B

 

TP31(L OUT 1) 

A

TP29(L OUT 2)

TP30(R OUT 2)

S2

S1

S3

PAL

NT

ST

BIL

J1(R)

J2(L)

J3

TP2(R OUT)

B

TP3(L OUT)

A

TP1(GND)

TP26

TP24

TP25

CN2

CH2

CN1

Use the CPC-7 jig
(J-6082-382-A)

Red

Red

White

CN910

VC-214 board

GND

REC RF

RF SWP

A

 :1.5MHz deviation adjustment.

B

 :1.7MHz deviation adjustment.

To Audio terminal

White

+
–

Stabilized power supply

  (+7Vdc to +9Vdc)

Fig. 5-3-19.

5-44

A

Approx. 2msec

Fig. 5-3-20.

Sets the spectrum of the L-ch ((L+R)/2 signal) level modulated
during recording. If deviated, the crosstalk signal of the audio signal
will occur and the audio level will drop during both playback and
recording.

Mode

VTR recording

Signal

Input the AFM DEV jig output signal to
the left and right audio input terminal

Measurement Point

CH1: AFM DEV jig TP31
CH2: AFM DEV jig TP3

Measuring Instrument

Oscilloscope

ADD mode
CH2 INV mode

Adjustment Page

F

Adjustment Address

62

Specified Value

The level difference between CH1 signal
and CH2 signal should be minimum.

Connection:
1)

Connect TP24 ,TP25 and TP26 of the AFM DEV jig to CN910
of the VC-214 board.

TP24(GND) ................ Pin 8 of CN910
TP25(REC RF) ........... Pin 0 of CN910
TP26(RF SWP) .......... Pin !¡ of CN910

2)

Connect the audio output terminal (J1 and J2) of the AFM DEV
jig to AUDIO terminal of the unit.

3)

Connect TP28(DC), TP27(GND) of the AFM DEV jig to the
DC power supply (+7Vdc to +9Vdc).

4)

Set the AFM DEV jig switches to the following positions.

S1 ........................... BIL Position
S2 ........................... PAL Position
S3 ........................... SIN Position

Preparations only for the model without REC switch:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 14, after memorizing the data, set the
bit value of bit1 to “1”. (Refer to “4-3, 3. Bit value
discrimination” of “5-4. Service Mode”).

3)

Select page: D, address: 15, after memorizing the data, set the
bit value of bit7 to “0”.

4)

Set to recording mode. (Use the wireless remote commander
of 8mm VCR.)

Adjusting method :
1)

Match the vertical ranges of CH1 and CH2 of the oscilloscope
to each other.

2)

Set the oscilloscope to the ADD mode and CH2 to the INV
(invert) mode.

3)

Select page: 0, address: 01, and set data: 01.

4)

Select page: F, address: 62, change the data and minimize the
audio signal level difference (A).

5)

Press the PAUSE button of the adjustment remote commander.

6)

Select page: 0, address: 01, and set data: 00.

Processing after completed adjustment only for the model
without REC switch:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 14, and set the data memorized at step
2) of “Preparations only for the model without REC switch”.

3)

Press the PAUSE button of the adjustment remote commander.

4)

Select page: D, address: 15, and set the data memorized at step
3) of “Preparations only for the model without REC switch”.

5)

Press the PAUSE button.

6)

Select page: 0, address: 01, and set data: 00.