DOWNLOAD Sony CCD-TR913E / CCD-TR950E Service Manual ↓ Size: 33.08 MB | Pages: 127 in PDF or view online for FREE

5-21

The back light (fluorescent tube) is driven by a high voltage AC
power supply. Therefore, do not touch the back light holder to
avoid electrical shock.

When replacing the LCD unit, be careful to prevent damages
caused by static electricity.

Most of the measuring points for adjusting the viewfinder system
are concentrated in CN910 of the VC-214 board.
Connect the Measuring Instruments via the CPC-7 jig (J-6082-382-A).
The following table shows the Pin No. and signal name of CN910.

Mode

Camera

Subject

Arbitrary

Adjustment Page

E

Adjustment Address

C5 to D0, FF

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: E, and input the data in the following table.

To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time
to set the data.

3)

Select page: 0, address: 01, and set data: 00.

C5

C6

C7

C8

C9

CA

CB

CC

CD

CE

CF

D0

FF

70

77

80

80

80

6E

50

F8

A8

40

90

70

A0

VCO adj.

Bright adj.

Contrast adj.

White balance adj.

White balance adj.

Fixed data

Fixed data

Fixed data

Fixed data

Fixed data

Backlight consumption current adj.

Fixed data

Backlight consumption current adj.

1

2

3

4

5

6

7

8

LANC SIG

XCPC IN

IR VIDEO

AFC F0

BPF MONI

PB RF

RF AGC IN

REG GND

9

10

11

12

13

14

15

16

RF AGC OUT

REC RF

RF SWP

CAP FG

EVF BL

EVF BL 4.75V

VCO

EVF VG

Table 5-1-5.

Fig. 5-1-11.

CN910

1

16

Screw driver (–)

Cover

5-22

Set the VCO free-run frequency. If deviated, the EVF screen will be
blurred.

Mode

Camera

Subject

Arbitrary

Measurement Point

Pin !∞ of CN910 (VCO) on VC-214
board

Measuring Instrument

Oscilloscope (DC range)

Adjustment Page

E

Adjustment Address

C5

Specified Value

A=1.8 ± 0.1V

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 01, set data: 55, and press the PAUSE
button of the adjustment remote commander.

3)

Check the GND level of the oscilloscope.

4)

Select page: E, address: C5, change the data and set the VCO
output voltage (A) to the specified value.

5)

Press the PAUSE button.

6)

Select page: 2, address: 01, set data: 00, and press the PAUSE
button.

7)

Select page: 0, address: 01, and set data: 00.

Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated
(whitish).

Mode

Camera

Subject

Arbitrary

Measurement Point

Pin !§ of CN910 (EVF VG) on
VC-214 board

Measuring Instrument

Oscilloscope

Adjustment Page

E

Adjustment Address

C6

Specified Value

A=7.04 ± 0.01V

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 01, set data: 55, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: E, address: C6, change the data and set the voltage
(A) between the reversed waveform pedestal and non-reversed
waveform pedestal to the specified value.

4)

Press the PAUSE button.

5)

Select page: 2, address: 01, set data: 00, and press the PAUSE
button.

6)

Select page: 0, address: 01, and set data: 00.

H

A

GND level 
(0Vdc)

A

2H 

Pedestal 

Pedestal

Fig. 5-1-12.

Fig. 5-1-13.

5-23

Set the level of the VIDEO signal for driving the LCD to the specified
value. If deviated, the screen image will be blackish or saturated
(whitish).

Mode

Camera

Subject

Arbitrary

Measurement Point

Pin !§ of CN910 (EVF VG) on
VC-214 board

Measuring Instrument

Oscilloscope

Adjustment Page

E

Adjustment Address

C7

Specified Value

A=2.0 ± 0.1V

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 01, set data: 55, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: E, address: C7, change the data and set the voltage
(A) between the 7 step peak and the pedestal to the specified
value.

4)

Press the PAUSE button.

5)

Select page: 2, address: 01, set data: 00, and press the PAUSE
button.

6)

Select page: 0, address: 01, and set data: 00.

Set the backlight luminance and color temperature.
If deviated, the image may become dark or bright.

Mode

Camera

Subject

Arbitrary

Measurement Point

+ Probe: Pin !¢ of CN910
(EVF BL 4.75V) on VC-214 board
– Probe: Pin !£ of CN910
(EVF BL) on VC-214 board

Measuring Instrument

Digital voltmeter

Adjustment Page

E

Adjustment Address

CF, FF

Specified Value

NORMAL mode : A=16 ± 1mVdc
BRIGHT mode : A=26 ± 1mVdc

Adjust 30 seconds after running on the power supply.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 01, set data: 55, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: 6, address: 6F, set data: 04, and press the PAUSE
button.

4)

Select page: E, address: CF, change the data and set the voltage
difference (A) between Pin !¢ of CN910 (EVF BL 4.75V) and
Pin !£ of CN910 (EVF BL) to the specified value of NORMAL
mode.

5)

Press the PAUSE button.

6)

Select page: 6, address: 6F, set data: 02, and press the PAUSE
button.

7)

Select page: E, address: FF, change the data and set the voltage
difference (A) between Pin !¢ and Pin !£ to the specified value
of BRIGHT mode..

8)

Press the PAUSE button.

9)

Select page: 6, address: 6F, set data: 00, and press the PAUSE
button.

10) Select page: 2, address: 01, set data: 00, and press the PAUSE

button.

11) Select page: 0, address: 01, and set data: 00.

A

2H 

7 step peak

Pedestal

Fig. 5-1-14.

5-24

Correct the white balance.
If deviated, the reproduction of the EVF screen may degenerate.

Mode

Camera

Subject

Arbitrary

Measurement Point

Check on EVF screen

Measuring Instrument

Adjustment Page

E

Adjustment Address

C8, C9

Specified Value

The EVF screen should not be colored.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 2, address: 01, set data: 51, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: 2, address: 7D, and set data: 03.

4)

Select page: E, address: C5 and C6, set the data to the initial
value.

To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time
to set the data.

5)

Check that the EVF screen is not colored. If colored, change
the data of page: E, address: C8 and C9 so that the EVF screen
is not colored.

To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time
to set the data.

6)

Select page: 2, address: 7D, and set data: 00.

7)

Select page: 2, address: 01, set data: 00, and press the PAUSE
button.

8)

Select page: 0, address: 01, and set data: 00.

C8

C9

80

80