DOWNLOAD Sony CCD-TR311 / CCD-TR311E / CCD-TR411E / CCD-TR412E / CCD-TR511E / CCD-TR512E / CCD-TR640E / CCD-TR730E / CCD-TR840E / CCD-TR845E Service Manual ↓ Size: 19.31 MB | Pages: 127 in PDF or view online for FREE

The following adjusting instruments are used for adjusting the video
section.

1) TV monitor
2) Oscilloscope: 2 phenomena, band 30 MHz or wider, with delay

mode. (Use a 10:1 probe unless specified otherwise.)

3) Frequency counter
4) Pattern generator with video output terminal
5) Digital voltmeter
6) Audio generator
7) Audio level meter
8) Audio distortion meter
9) Audio attenuater
10) Regulated power supply
11) Alignment tape

[For NTSC model]
• For tracking adjustment (WR5-1NP)

Part Code: 8-967-995-02

• For video frequency characteristics adjustment

(WR5-7NE) Part Code: 8-967-995-13

• For checking Standard 8 mode operations

For LP (WR5-4NL)

Part Code: 8-967-995-51

For SP (WR5-5NSP)

Part Code: 8-967-995-42

The following alignment tapes can also be used.
WR5-4NSP (8-967-995-41)

• For checking AFM stereo operations (WR5-9NS)

Part Code: 8-967-995-23

For checking BPF adjustment (WR5-11NS)

Part Code: 8-967-995-71

[For PAL model]
• For tracking adjustment (WR5-1CP)

Part Code: 8-967-995-07

• For video frequency characteristics adjustment

(WR5-7NE) Part Code: 8-967-995-18

• For checking Standard 8 mode operations

For LP (WR5-4CL)

Part Code: 8-967-995-56

For SP (WR5-5CSP)

Part Code: 8-967-995-47

The following alignment tapes can also be used.
1) WR5-3CL (8-967-995-36)
2) WR5-4CSP (8-967-995-46)

• For checking Hi8 mode operation

For SP (WR5-8CSE)

Part Code: 8-967-995-48

For LP (WR5-8CLE)

Part Code: 8-967-995-57

• For checking AFM stereo operations (WR5-9CS)

Part Code: 8-967-995-28

For checking BPF adjustment (WR5-11CS)

Part Code: 8-967-995-76

12) Remote commander for adjustment (J-6082-053-B)
13) CPC-7 jig Part Code: J-6082-382-A
14) Power code Part Code: J-6082-223-A

Connect the adjusting remote commander to the LANC
jack, and set the HOLD switch to the “ADJ” side, or
press the battery switch of the battery terminal using
adhesive tape, etc.

15) AFM DEV jig (J-6082-312-A)
16) Extension cable (48P, 0.8mm) (J-6082-188-A)

1) The adjustments of this unit are performed in the VTR mode or

camera mode.
To set to the VTR mode, set the power switch to “VTR” (or
“PLAYER”) or set the “Forced VTR Power ON mode” using
the adjusting remote commander (Note 1).
To set to the Camera mode, set the power switch to “CAMERA”
or set the “Forced Camera Power ON mode” using the adjusting
remote commander (Note 2).
After completing adjustments, be sure to exit the “Forced VTR
Power ON Mode” or “Forced Camera Power ON Mode”.
(Note 3)

2) By setting the “Forced VTR Power ON mode” or “Forced Camera

Power ON mode”, the video section can be operate even if even
if the front panel block (MA-311 board, power switch,
microphone unit) has been removed. When removing the front
panel block disconnect the following connector.

1. VC-195 board CN903 (23P 0.5mm)

3) The lens block (CD-181 board) need not be connected except

during battery end adjustment. To remove, disconnect the
following connectors.

1. VC-195 board CN501 (16P, 0.5mm)
2. VC-195 board CN551 (23P, 0.5mm)

4) The intelligent accessory shoe (Intelligent accessory shoe model)

need not be assembled. If removing it. disconnect the following
connector.

1. VC-195 board CN909 (10P, 0.5mm)

5) Cabinet (R) ( Camera function switch (CF-49board), viewfinder)

need not be connected. But removing the cabinet (R) (removing
the VC-195 board CN911) means removing the lithium 3V power
supply (CF-49 board) , data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data. If
the cabinet (R) has been removed, the self-diagnosis data, data
on history of use (total drum rotation time etc. ) will be lost.
Before removing, note down the self-diagnosis data and data on
the history use. (Refer to the “Service Mode” for the data on the
history use.) To remove the cabinet (R), disconnect the following
connector.

1. VC-195 board CN911 (50P, 0.5mm) (COLOR EVF model)

(30P, 0.5mm)  (B/W EVF model)

Setting the “Forced VTR Power ON” mode
(VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press

the PAUSE button of the adjusting r emote
commander.

The above procedure will enable the VTR power to be
turned on with the front panel block removed.
After completing adjustments, be sure to exit the
“Forced VTR Power ON mode”.

Setting the “Forced Camera Power ON” mode
(Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press

the PAUSE button of the adjusting r emote
commander.
The above procedure will enable the camera power
to be turned on with the front panel block removed.
After completing adjustments, be sure to exit the
“Forced Camera Power ON mode”.

Exiting the “Forced Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press

the PAUSE button of the adjusting r emote
commander.

3) Select page: 0, address: 01, and set data: 00.

Some of the adjusting points of the video section are concentrated
at VC-195 board CN910. Connect the measuring instruments via
the CPC-7 jig (J-6082-382-A). The following table lists the pin
numbers and signal names of CN910.

Pin No.

Signal Name

Pin No.

Signal Name

1

LANC SIG

9

RF AGC OUT

2

XCPC IN

10

REC RF

3

IR VIDEO

11

RF SWP

4

AFC F0

12

CAP FG

5

BPF MONI

13

EVF BL

6

PB RF

14

EVF BL 4.75V

7

RF AGC IN

15

VCO

8

REG GND

16

EVF VG

Screw driver (–)

Cover

Connect the measuring instruments as shown in Fig. 5-3-2 and
perform the adjustments.

The following table lists alignment tapes which are available.
Use the tape specified in the signal column for each adjustment.
If the type of tape to be used for checking operations is not specified,
use whichever type.

Name

Tracking
WR5-1NP (NTSC)
WR5-1CP (PAL)

Video frequency
characteristics
WR5-7NE (NTSC)
WR5-7CE (PAL)
Operation check
(SP mode)
WR5-5NSP (NTSC)
WR5-5CSP (PAL)
Operation check
(SP mode)
WR5-8NSE (NTSC)
WR5-8CSE (PAL)
Operation check
(LP mode)
WR5-4NL (NTSC)
WR5-4CL (PAL)
Operation check
(LP mode)
WR5-8NLE (NTSC)
WR5-8CLE (PAL)
AFM stereo
Operation check
WR5-9NS (NTSC)
WR5-9CS (PAL)
BPF adjustment
WR5-11NS (NTSC)
WR5-11CS (PAL)

Record

-ing

mode

Standard

8 mm

Hi8

Standard

8 mm

Hi8

Standard

8 mm

Hi8

Standard

8 mm

Standard

8 mm

Tape

type

MP

ME

MP

ME

MP

ME

MP

MP

Tape

speed

SP

SP

(NTSC)

LP

(PAL)

SP

SP

LP

LP

SP

SP

Usage

Tape path
adjustment
Switching
position
adjustment

Frequency
characteristics
adjustment

Checking
operations

AFM stereo
Checking
operations

BPF
adjustment

Tape type

MP ..... Particle type metal tape
ME ..... Evaporated type metal tape

Battery terminal

Regulated power supply
8.4

±

0.1Vdc

Main Unit

VIDEO

VIDEO terminal

TV monitor

Connect when using the camera
mode or playing back.

Connecting the TV Monitor and Regulated Power Supply

Fig. 5-3-3. shows the 75% color bar signals recorded on the
alignment tape.

Measure using the VIDEO terminal (Terminated at 75 

Ω

).