DOWNLOAD Sony DVP-NS3100ES Service Manual ↓ Size: 10.53 MB | Pages: 102 in PDF or view online for FREE

17

On this test mode screen, selecting [7] enables the machine operation
such as disc loading. The following screen appears.

Display when [7] is selected in the Drive Manual Operation

## Changer Manual Move ##

ENTER  : Mecha Initial

PLAY   : Loading In

STOP   : Loading Out

OP/CL  : Door Open/Close

UP     : Poper Up

DOWN   : Poper Down

jogFOR : Table R StepTurn

jogPRV : Table L StepTurn

DISP   : Sensor Status

RETURN : Exit

[ENTER]

: Performs initialization of mechanism deck.

Mecha Initial

Because the mechanical initialization is

performed when the machine enters the Drive
Manual Operation mode, use this item when
an error such as adjustment error occurs.

[PLAY]

: Not used in this set.

Loading In

[STOP]

: Not used in this set.

Loading Out

[OP/CL]

: Opens and closes the door.

Door Open/Close
( 

Z

key)

[UP]

: Not used in this set.

Poper Up

[DOWN]

: Not used in this set.

Poper Down

[jog FOR]

: Not used in this set.

Table R step Turn

[jog PRV]

: Not used in this set.

Table L step Turn

[DISP]

: Not used in this set.

Sensor Status

Not used in this set.

The mechanism aging is not supported.

### EMG. History ###

Laser Hours

            CD         xxh xxm

            DVD        xxh xxm

01.00 00 00 00    00 00 00 00

   00 00 00 00    00 00 00 00

02.00 00 00 00    00 00 00 00

   00 00 00 00    00 00 00 00

Select : 1-9   Scroll : UP/DOWN

(1: Last EMG.)   Exit : RETURN

On the Test Mode Menu screen, selecting [4]  displays the
information such as servo emergency history. The history
information from last “1” up to “10” can be scrolled with [

Q] key or

[q]  key. Also, specific information can be displayed by directly
entering that number with the ten-key pad from [1] to [9].
The upper two lines display the laser ON total hours. Data below
minutes are omitted.

Clearing History Information

Clearing laser hours
Press [TOP MENU] and [CLEAR] keys in this order.
Both CD and DVD data are cleared.
Clearing emergency history
Press [DISPLAY] and [CLEAR] keys in this order.
Initializing setup data
Press [MENU] and [CLEAR] keys in this order.
The data have been initialized when “Set Up Initialized”

message is displayed.

The EMG. History display screen will be restored soon.

### Version Information ###

IF con     Ver:x.xxx(xxxx)

B/E        Ver:xxx xxx

F/E        Ver:xx

        Model    :DVP-NS3100ES(X)

        Region   :xxx(x)

Exit : RETURN

IF con : IC404 on the MAIN board
B/E

: IC256 on the MAIN board

F/E

: IC105 on the MAIN board

On the Test Mode Menu screen, selecting [6] displays color bars for
video level adjustment. During display of color bars, OSD disappears
but the menu screen will be restored if pressing the [RETURN] key.

18

Execute the Self Check Mode along the following flow.

The Display Test mode starts if either of the following conditions is
satisfied.

Condition 1:
With the SELF_CHECK (pin oj) of the IF CON (IC404) on the
MAIN board kept “low”, turn the power on.

Condition 2:
While pressing the

x

key on the set when the set is in standby

state, press the [RETURN] 

t  [DISPLAY]  key on the remote

commander and the mode transits to the Self Check mode.

When the Self Check mode started, “TEST START” is displayed
on the FL tube for 2 seconds and then the Self Check proceeds to
the IF CON information display.

To release the Self Check mode, disconnect the AC plug.

When enter this mode, it displays as follows.

If the

x

button is pressed, the test proceeds to the following FL

tube GRID and SEGMENT check.

First, a grid lights up one after another, and when grid 16 lights up,
all grids light up.
Next, all grids go off, and segments are displayed while changing
the patterns.
A way of this display is repeated.
(The interval of grid lighting is 0.2 second, and that of segment
lighting is 0.4 second.)

If the

x

button is pressed, the test proceeds to the following SIRCS

reception check.

Upon start of the SIRCS reception check, “SIRCS CHECK” is
displayed on the FL tube.
Once the SIRCS key code is received, the test proceeds to the
following Key check.

If the

x

button is pressed as a cancel processing of the SIRCS

reception check, the test proceeds to the following Key check.

x

19

After the Jog and LED check finished, it displays result of Display
Test mode.
At this time, even if a signal from a key on the set or remote
commander is received, nothing changes.

At the SIRCS reception check, Key check, Jog and LED check, if
you proceed to the next check without completing current check,
the check name that has not completed yet is displayed instead of
“TEST OK”, as follows.

If SIRCS reception check has not completed

“SIRCS NG”

(If JOG dial is pressed during SIRCS

reception check)

If KEY check has not completed

“KEY NG”

(If SIRCS key code is received during KEY

check)

If JOG and LED check has not completed

“JOG LED NG”

(If JOG dial is pressed without rotating JOG

dial even once during JOG and LED check)

Also, if two or more checks have not completed yet

All three checks are erroneous

“SI  KY JO NG”

Two checks are erroneous

“SI

   JO NG”

“SI  KY

NG”

“     KY JO NG”

Each error is displayed at the fixed position of the FL tube (not left
aligned), and the items that have completed are blank.

The alphabets mentioned above denote the following checks.
SI : SIRCS reception check
KY : Key check
JO : Jog and LED check
NG : There are error items.

After the SIRCS reception check finished, the Key check is executed.
Upon start of the Key check, “KEY CHECK” is displayed on the
FL tube.
9 keys are checked as described below.
Each time a key is pressed, the specified segment lights up, and at
one second after all keys were pressed, all of FL tube go off and the
Key check finishes.

If the SIRCS key code is received as a cancel processing of the Key
check, the test proceeds to the following Jog and LED check.

MULTI

HYBRID

AUDIO
VIDEO

VCD

DVD

CD

SA-CD

I/

1

SA-CD/CD

MULTI/2CH

DIMMER

VIDEO OFF

A

N

X

x

H

After the Key check finished, the Jog and LED check is executed as
follows.
Upon start of the Jog and LED check, “JOG AND LED” is displayed
on the FL tube.
There are six LEDs. The order in which the LEDs light up when the
.>  knob is turned as described below.

If the

x

button is pressed during the Jog and LED check, the Jog

and LED check finishes and it displays result of the Display Test
mode. (See next item)

20

1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,

with delay mode

3) Remote commander

RM-ASP002

4) CD reference disc

LUV-P01 (4-999-032-01)
YEDS-18 (3-702-101-01)
PATD-012 (4-225-203-01)

5) DVD reference disc

TDV-520CS0 (J-2501-236-A) (single layer) (NTSC)
HLX-503 (J-6090-069-A) (single layer) (NTSC)
HLX-504 (J-6090-088-A) (single layer) (NTSC)
TDV-540C (J-2501-235-A) (dual layer) (NTSC, Opposite)
HLX-501 (J-6090-071-A) (dual layer) (NTSC)
HLX-505 (J-6090-089-A) (dual layer) (NTSC)

6) SA-CD reference disc

HLXA-509 (J-6090-090-A)

7) Extension Cable (J-2501-086-A)

In the case of quality judgement when the defect of the optical
traverse unit like the skip etc. is thought, and in case of operation
confirming when replacing optical traverse unit, select “ALL” of
“1. DRIVE AUTO ADJUSTMENT” in the test mode (refer to page
13, 15), adjust DVD-SL (single layer), CD and DVD-DL (dual layer),
and confirm whether the result of each setting value is the range of
the following specification.

DVD-SL

CD

DVD-DL

L0

L1

An.Off.A

20 to E0

20 to E0

20 to E0

–

An.Off.B

20 to E0

20 to E0

20 to E0

–

An.Off.C

20 to E0

20 to E0

20 to E0

–

An.Off.D

20 to E0

20 to E0

20 to E0

–

An.Off.E

–

20 to E0

–

–

An.Off.F

–

20 to E0

–

–

An.G.Main

0E to 1C

0E to 1A

1D to 28

1D to 28

An.G.Side

–

0C to 1C

–

–

RF level

70 to F0

70 to F0

60 to F0

60 to F0

FE S L0

74 to FF

74 to FF

54 to FF

–

FE S L1

–

–

–

54 to FF

VTS2

00 to 10

–

–

–

TE levDVD

28 to 48

–

28 to 48

28 to 48

TE levCD

–

34 to 60

–

–

TE Offset

D0 to FF

A0

 

to

 

CC

20 to E0

20 to E0

00 to 30

00 to 30

00 to 30

FCS Gain

20 to 3F

18 to 38

20 to 48

20 to 48

TRK Gain

30 to 50

30 to 50

30 to 50

30 to 50

FCS Bal.1

–

–

–

–

FCS Bal.2

36 to 4F

36 to 4F

36 to 4F

36 to 4F

REFQ1

–

–

–

–

REFQ2

0C to 30

14 to 24

0C to 30

0C to 30

Jitter

07 to 14

07 to 0F

07 to 14

–

<Purpose>
This adjusts progressive video output level. If it is incorrect, correct
brightness will not be attained when connected to, for instance,
projector.

Mode

Video level adjustment in test mode

Signal

Color bars

Check point

COMPONENT VIDEO OUT (Y)

connector (J620) (75 

Ω

 terminated)

Instrument

Oscilloscope

Adjusting element

RV600

Specification

1.0 

+

–

0
0

.
.

0
0

4
2

 Vp-p

1) In the Test Mode Menu, select the “6. Video Level Adjustment”

so that color bars are generated.

2) Adjust the RV600 to attain 1.0 

+

–

0
0

.
.

0
0

4
2

 Vp-p.

1.0 

+0.04

 Vp-p

–0.02

1.0 

+0.04

 Vp-p

–0.02

<Purpose>
This adjustment is made to satisfy the NTSC standard, and if not
adjusted correctly, the brightness will be too large or small.

Mode

Video level adjustment in test mode

Signal

Color bars

Check point

VIDEO OUT connector (J502)

(75 

Ω

 terminated)

Instrument

Oscilloscope

Adjusting element

RV601

Specification

1.0 

+

–

0
0

.
.

0
0

4
2

 Vp-p

1) In the Test Mode Menu, select the “6. Video Level Adjustment”

so that color bars are generated.

2) Adjust the RV601 to attain 1.0 

+

–

0
0

.
.

0
0

4
2

 Vp-p.