Sony DVP-NS3100ES Service Manual ▷ View online
13
DVP-NS3100ES
0-3. Peripheral
(3-2) Flash Rom
Data delete
t write t read, and accord check
Error 32: Delete error
Error 33: Write error
Error 34: Read data discord
Error may occur due to defect of access with the CPU (MAIN
board IC256).
Error 33: Write error
Error 34: Read data discord
Error may occur due to defect of access with the CPU (MAIN
board IC256).
(3-3) SA-CD Check
Data write
t read, and accord check
Error 36: Write/read data discord
Check for SA-CD circuit (MAIN board IC502 and around
circuit).
Check for SA-CD circuit (MAIN board IC502 and around
circuit).
(3-4) Venc Check
Register write
t read, and accord check
Error 37: Write/read data discord
Error may occur due to defect of access with the CPU (MAIN
board IC256).
Error may occur due to defect of access with the CPU (MAIN
board IC256).
(3-6) LIP sync RAM Check
Data write
t read, and accord check
Error 38: Write/read data discord
External RAM check for I/P sync (MAIN board IC552)
External RAM check for I/P sync (MAIN board IC552)
(3-7) PROV Check
Data write
t read, and accord check
Error 39: Write/read data discord
External RAM check for I/P converter (MAIN board IC603)
too.
External RAM check for I/P converter (MAIN board IC603)
too.
(3-8) HDMI Check
Register write
t read, and accord check
Error 43: Write/read data discord
Error may occur due to defect of access with the HDMI
transmitter (MAIN board IC607).
Error may occur due to defect of access with the HDMI
transmitter (MAIN board IC607).
0-4. Servo
(4-2) Servo (F/E) Check
Data write
t read, and accord check
Error 41: Read data discord
0x9249, 0x2942 and 0x4294 are written to the RAM address
0x602 of the DVD interface (front-end) (MAIN board IC105)
and then read for checking.
0x9249, 0x2942 and 0x4294 are written to the RAM address
0x602 of the DVD interface (front-end) (MAIN board IC105)
and then read for checking.
0-5. Video
(5-2) Interlace
Error: Not detected.
The command is transferred to the video encoder (MAIN
board IC606), and change the video signal to interlace.
The command is transferred to the video encoder (MAIN
board IC606), and change the video signal to interlace.
(5-3) Progressive
AVD color bar command write
t Video (Composite, Y/C)
OUT
Error: Not detected.
The command is transferred to the video encoder (MAIN
board IC606), and change the video signal to progressive.
Error: Not detected.
The command is transferred to the video encoder (MAIN
board IC606), and change the video signal to progressive.
(5-4) Color Bar
Error: Not detected.
The command is transferred to the video encoder (MAIN
board IC606), and the color bar signals are output from video
terminals.
The command is transferred to the video encoder (MAIN
board IC606), and the color bar signals are output from video
terminals.
0-6. Audio
Not used.
1. Drive Auto Adjustment
DVD reference disc:
Single Layer
TDV-520CS0 (J-2501-236-A) (NTSC)
HLX-503 (J-6090-069-A) (NTSC)
HLX-504 (J-6090-088-A) (NTSC)
HLX-503 (J-6090-069-A) (NTSC)
HLX-504 (J-6090-088-A) (NTSC)
Dual Layer
TDV-540C (J-2501-235-A) (NTSC, Opposite)
HLX-501 (J-6090-071-A) (NTSC)
HLX-505 (J-6090-089-A) (NTSC)
HLX-501 (J-6090-071-A) (NTSC)
HLX-505 (J-6090-089-A) (NTSC)
CD reference disc:
LUV-P01 (4-999-032-01)
YEDS-18 (3-702-101-01)
PATD-012 (4-225-203-01)
YEDS-18 (3-702-101-01)
PATD-012 (4-225-203-01)
On the Test Mode Menu screen, press [1] key on the remote
commander, and the drive auto adjustment menu will be displayed.
commander, and the drive auto adjustment menu will be displayed.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL (DL:Parallel)
1. DVD-SL
2. CD
3. DVD-DL (Parallel)
4. ALL (DL:Opposite)
5. DVD-DL (Opposite)
9. CLEAR DATA
Exit: RETURN
Normally, [0] or [4] is selected to adjust DVD (single layer), CD,
and DVD (dual layer) in this order. But, individual items can be
adjusted for the case where adjustment is suspended due to an error.
In this mode, the adjustment can be made easily through the
operation following the message displayed on the screen. Which
disc is currently adjusted is displayed on the fluorescent display
tube.
and DVD (dual layer) in this order. But, individual items can be
adjusted for the case where adjustment is suspended due to an error.
In this mode, the adjustment can be made easily through the
operation following the message displayed on the screen. Which
disc is currently adjusted is displayed on the fluorescent display
tube.
1-0. ALL (DL: Parallel)
Select [0] and press the [ENTER] key. Then, [1] DVD-SL disc, [2]
CD disc, and [3] DVD-DL (Parallel) disc are adjusted in this order.
Each time one disc was adjusted, it is ejected, and therefore exchange
the disc following the message. You can exit the adjustment by
pressing the
CD disc, and [3] DVD-DL (Parallel) disc are adjusted in this order.
Each time one disc was adjusted, it is ejected, and therefore exchange
the disc following the message. You can exit the adjustment by
pressing the
x
button. In adjusting each disc, the mirror time is
measured to check the disc type. In the auto adjustment, whether
the disc type is correct is not checked unlike conventional models,
and accordingly, take care not to insert a different type of disc.
the disc type is correct is not checked unlike conventional models,
and accordingly, take care not to insert a different type of disc.
Set Disc
1: DVD-SL (TDV-520CS0 or HLX-503 or HLX-504)
2: CD (LUV-P01 or YEDS-18 or PATD-012)
3: DVD-DL (HLX-501 or HLX-505)
1: DVD-SL (TDV-520CS0 or HLX-503 or HLX-504)
2: CD (LUV-P01 or YEDS-18 or PATD-012)
3: DVD-DL (HLX-501 or HLX-505)
14
DVP-NS3100ES
1-1. DVD Single Layer Disc
Select [1], insert DVD single layer disc, and press [ENTER] key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the flash memory. If there is no
disc on the disc tray, the tray will be open to wait for closing. If
there is a disc on the disc tray, the adjustment starts immediately. If
you put a disc prior to adjustment, confirm that the SL disc is set on
the disc tray. Also, when the adjustment is completed, the result of
the each setting value is displayed as follows.
and the adjustment will be made through the following steps, then
adjusted values will be written to the flash memory. If there is no
disc on the disc tray, the tray will be open to wait for closing. If
there is a disc on the disc tray, the adjustment starts immediately. If
you put a disc prior to adjustment, confirm that the SL disc is set on
the disc tray. Also, when the adjustment is completed, the result of
the each setting value is displayed as follows.
DVD Single Layer Disc Adjustment Steps
1. Sled Reset
2. Set Disc Type SL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tracking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. All Servo Off
2. Set Disc Type SL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tracking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. All Servo Off
Result Display
Result
disc type : SL
An.Off.AB xx xx TE levDVD xx
An.Off.CD xx xx TE levCD --
An.Off.EF -- -- TE Offset xx
An.G.Main xx FCS Gain xx
An.G.Side -- TRK Gain xx
RF level xx FCS Bal. -- xx
FE S L0,1 xx -- REFQ -- xx
VTS2 xx Jitter xx
Exit:RETURN
1-2. CD Disc
Select [2], insert CD disc, and press [ENTER] key, and the adjustment
will be made through the following steps, then adjusted values will
be written to the flash memory. If there is no disc on the disc tray,
the tray will be open to wait for closing. If there is a disc on the disc
tray, the adjustment starts immediately. If you put a disc prior to
adjustment, confirm that the CD is set on the disc tray. Also, when
the adjustment is completed, the result of the each setting value is
displayed as follows.
will be made through the following steps, then adjusted values will
be written to the flash memory. If there is no disc on the disc tray,
the tray will be open to wait for closing. If there is a disc on the disc
tray, the adjustment starts immediately. If you put a disc prior to
adjustment, confirm that the CD is set on the disc tray. Also, when
the adjustment is completed, the result of the each setting value is
displayed as follows.
1-3. DVD Dual Layer Disc (Parallel)
Select [3], insert DVD dual layer disc, and press [ENTER] key, and
the adjustment will be made through the following steps, then
adjusted values will be written to the flash memory. If there is no
disc on the disc tray, the tray will be open to wait for closing. If
there is a disc on the disc tray, the adjustment starts immediately. If
you put a disc prior to adjustment, confirm that the DL disc is set on
the disc tray. Also, when the adjustment is completed, the result of
the each setting value is displayed as follows.
the adjustment will be made through the following steps, then
adjusted values will be written to the flash memory. If there is no
disc on the disc tray, the tray will be open to wait for closing. If
there is a disc on the disc tray, the adjustment starts immediately. If
you put a disc prior to adjustment, confirm that the DL disc is set on
the disc tray. Also, when the adjustment is completed, the result of
the each setting value is displayed as follows.
DVD Dual Layer Disc Adjustment Steps
1. Sled Reset
2. Set Disc Type DL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tacking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
2. Set Disc Type DL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tacking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
CD Adjustment Steps
1. Sled Reset
2. Set Disc Type CD
3. Laser Diode (CD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Auto Focus Gain Adjust
13. Auto Tracking Gain Adjust
14. Sled ON
15. CLV ON
16. Auto Focus Balance Adjust
17. Auto RFEQ Boost Adjust
18. Jitter measure
19. Search Check
20. All Servo Off
2. Set Disc Type CD
3. Laser Diode (CD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Auto Focus Gain Adjust
13. Auto Tracking Gain Adjust
14. Sled ON
15. CLV ON
16. Auto Focus Balance Adjust
17. Auto RFEQ Boost Adjust
18. Jitter measure
19. Search Check
20. All Servo Off
Result Display
Result
disc type : CD
An.Off.AB xx xx TE levDVD --
An.Off.CD xx xx TE levCD xx
An.Off.EF xx xx TE Offset xx
An.G.Main xx FCS Gain xx
An.G.Side xx TRK Gain xx
RF level xx FCS Bal. -- xx
FE S L0,1 xx -- REFQ -- xx
VTS2 -- Jitter xx
Exit:RETURN
15
DVP-NS3100ES
1-5. DVD Dual Layer Disc (Opposite)
Note:
Make sure, using the TDV-540C in this adjustment.
Select [5], insert DVD dual layer disc (TDV-540C), and press
[ENTER] key, and the adjustment will be made through the following
steps, then adjusted values will be written to the flash memory. If
there is no disc on the disc tray, the tray will be open to wait for
closing. If there is a disc on the disc tray, the adjustment starts
immediately. If you put a disc prior to adjustment, confirm that the
DL disc is set on the disc tray.
[ENTER] key, and the adjustment will be made through the following
steps, then adjusted values will be written to the flash memory. If
there is no disc on the disc tray, the tray will be open to wait for
closing. If there is a disc on the disc tray, the adjustment starts
immediately. If you put a disc prior to adjustment, confirm that the
DL disc is set on the disc tray.
22. Jitter measure
23. Search Check
24. Focus Jump (L0
23. Search Check
24. Focus Jump (L0
t L1)
25. Tracking Off
26. Tracking Error Level Adjust
27. Tracking Error Offset Adjust
28. Tracking ON
29. Auto Focus Gain Adjust L1
30. Auto Tracking Gain Adjust L1
31. Sled ON
32. CLV ON
33. Auto Focus Balance Adjust L1
34. Auto RFEQ Boost Adjust L1
35. Search Check
36. All Servo Off
26. Tracking Error Level Adjust
27. Tracking Error Offset Adjust
28. Tracking ON
29. Auto Focus Gain Adjust L1
30. Auto Tracking Gain Adjust L1
31. Sled ON
32. CLV ON
33. Auto Focus Balance Adjust L1
34. Auto RFEQ Boost Adjust L1
35. Search Check
36. All Servo Off
Result Display
Result
disc type : DL L0
An.Off.AB xx xx TE levDVD xx
An.Off.CD xx xx TE levCD --
An.Off.EF -- -- TE Offset xx
An.G.Main xx FCS Gain xx
An.G.Side -- TRK Gain xx
RF level xx FCS Bal. -- xx
FE S L0,1 xx -- REFQ -- xx
VTS2 -- Jitter xx
1:L1 Page
Exit:RETURN
Result
disc type : DL L1
An.Off.AB -- -- TE levDVD xx
An.Off.CD -- -- TE levCD --
An.Off.EF -- -- TE Offset xx
An.G.Main xx FCS Gain xx
An.G.Side -- TRK Gain xx
RF level xx FCS Bal. -- xx
FE S L0,1 -- xx REFQ -- xx
VTS2 -- Jitter --
0:L0 Page
Exit:RETURN
1-4. ALL (DL: Opposite)
Select [4] and press the [ENTER] key. Then, [1] DVD-SL disc, [2]
CD disc, and [5] DVD-DL (Opposite) disc are adjusted in this order.
Each time one disc was adjusted, it is ejected, and therefore exchange
the disc following the message. You can exit the adjustment by
pressing the
CD disc, and [5] DVD-DL (Opposite) disc are adjusted in this order.
Each time one disc was adjusted, it is ejected, and therefore exchange
the disc following the message. You can exit the adjustment by
pressing the
x
button. In adjusting each disc, the mirror time is
measured to check the disc type. In the auto adjustment, whether
the disc type is correct is not checked unlike conventional models,
and accordingly, take care not to insert a different type of disc.
the disc type is correct is not checked unlike conventional models,
and accordingly, take care not to insert a different type of disc.
Set Disc
1: DVD-SL (TDV-520CS0 or HLX-503 or HLX-504)
2: CD (LUV-P01 or YEDS-18 or PATD-012)
3: DVD-DL (TDV-540C only)
1: DVD-SL (TDV-520CS0 or HLX-503 or HLX-504)
2: CD (LUV-P01 or YEDS-18 or PATD-012)
3: DVD-DL (TDV-540C only)
DVD Dual Layer Disc Adjustment Steps
1. Sled Reset
2. Set Disc Type DL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tacking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. Focus Jump (L0
2. Set Disc Type DL
3. Laser Diode (DVD) ON
4. Focus Error Check
5. Focus ON
6. Spindle Start
7. Tracking Error Level Adjust
8. Tracking Error Offset Adjust
9. Tracking ON
10. RF Level Adjustment
11. Spindle Calibration
12. Tracking Off
13. Tracking Error Level Adjust 2nd
14. Tracking Error Offset Adjust 2nd
15. Tracking ON
16. Auto Focus Gain Adjust L0
17. Auto Tacking Gain Adjust L0
18. Sled ON
19. CLV ON
20. Auto Focus Balance Adjust L0
21. Auto RFEQ Boost Adjust L0
22. Jitter measure
23. Search Check
24. Focus Jump (L0
t L1)
25. Tracking Off
26. Tracking Error Level Adjust
27. Tracking Error Offset Adjust
28. Tracking ON
29. Auto Focus Gain Adjust L1
30. Auto Tracking Gain Adjust L1
31. Sled ON
32. CLV ON
33. Auto Focus Balance Adjust L1
34. Auto RFEQ Boost Adjust L1
35. Search Check
36. All Servo Off
26. Tracking Error Level Adjust
27. Tracking Error Offset Adjust
28. Tracking ON
29. Auto Focus Gain Adjust L1
30. Auto Tracking Gain Adjust L1
31. Sled ON
32. CLV ON
33. Auto Focus Balance Adjust L1
34. Auto RFEQ Boost Adjust L1
35. Search Check
36. All Servo Off
2. Drive Manual Operation
On the Test Mode Menu screen, select [2], and the manual operation
menu will be displayed. For the manual operation, each servo on/
off control and adjustment can be executed manually.
menu will be displayed. For the manual operation, each servo on/
off control and adjustment can be executed manually.
## Drive Manual Operation ##
2. Operation Commands
3. Servo Control
4. Track/Layer Jump
6. Memory Check
7. Changer Manual Move
8. Changer Mecha Check
Exit: RETURN
Model :DVP-NS3100ES
Revision:xxx xxx
Basic operation (controllable from front panel or remote
commander)
commander)
I/
1
: Power OFF
x
: Servo stop
Z
: Stop+Eject/Loading
O
(RETURN) : Return to Operation Menu or Test Mode Menu
>
,
.
: Transition between sub modes of menu
[1] to [9], [0]
: Selection of menu and items
Cursor [
Q]/[q] : Increase/Decrease in manually adjusted value
16
DVP-NS3100ES
2-6. Memory Check
The display image is shown below and three screens in total can be
selected.
selected.
6. Memory Check Flash Data 1
CD SL L0 L1
An.Off A xx xx xx xx
An.Off B xx xx xx xx
An.Off C xx xx xx xx
An.Off D xx xx xx xx
An.Off E xx xx xx xx
An.Off F xx xx xx xx
An.G.Main xx xx xx xx
An.G.Side xx xx xx xx
RF level xx xx xx xx
FE S level xx xx xx xx
Down:NextPage
Exit:RETURN
6. Memory Check Flash Data 2
CD SL L0 L1
TE Level xx xx xx xx
TE Offset xx xx xx xx
FCS Gain xx xx xx xx
TRK Gain xx xx xx xx
FCS Bal.1 xx xx xx xx
FCS Bal.2 xx xx xx xx
RFEQ 1 xx xx xx xx
RFEQ 2 xx xx xx xx
VTS2 xx xx xx xx
Jitter xx xx xx xx
Up/Dn:Prev/NextPage
Exit:RETURN
6. Memory Check Flash Data 3
CD SL L0 L1
VTS1 xx xx xx xx
Up:PrevPage
Exit:RETURN
2-3. Servo Control
### Drive Manual Operation ###
3. Servo Control
1. LD DVD Off/On
2. LD CD Off/On
3. Focus Off/On
4. Spindle Off/On
5. Track Off/On
6. Sled Off/On
8. Focus Ramp
Exit: RETURN
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
[1] LD DVD
: Turn on/off the laser for DVD.
[2] LD CD
: Turn on/off the laser for CD.
[3] Focus
: Turn on/off the focus servo.
[4] Spindle
: Turn on/off the spindle servo.
[5] Track
: Turn on/off the tracking servo.
[6] Sled
: Turn on/off the sled servo.
[8] Focus Ramp : In the laser diode on and focus servo off status,
repeat the focus up/down.
2-4. Track/Layer Jump
4. Track/Layer Jump
1. 1Tj FWD
2. 1Tj REV
3. 200Tj FWD
4. 200Tj REV
5. 2kTj FWD
6. 2kTj REV
9. Lj (L1->L0)
0. Lj (L0->L1)
Exit: RETURN
On this screen, track jump, etc. can be performed. Only for the DVD-
DL, the focus jump and layer jump are displayed in the right field.
DL, the focus jump and layer jump are displayed in the right field.
[1] 1Tj FWD
: 1-track jump forward.
[2] 1Tj REV
: 1-track jump reverse.
[3] 200Tj FWD : 200-track jump forward.
[4] 200Tj REV : 200-track jump reverse.
[5] 2kTj FWD : 2k-track jump forward.
[6] 2kTj REV
[4] 200Tj REV : 200-track jump reverse.
[5] 2kTj FWD : 2k-track jump forward.
[6] 2kTj REV
: 2k-track jump reverse.
[9] Lj (L1->L0) : Layer jump.
[0] Lj (L0->L1) : Layer jump.
[0] Lj (L0->L1) : Layer jump.
2-2. Operation Commands
### Drive Manual Operation ###
2. Operation Commands
1. Search Disc (DVD Priority)
2. Search Disc (CD Priority)
3. PLAY
4. Pause
5. Stop
Exit: RETURN
[1] Serch Disc
: DVD SDISC (F/E command) is performed by
(DVD Priority)
priority.
[2] Serch Disc
: CD SDISC (F/E command) is performed by
(CD Priority)
priority.
[3] PLAY
: Playback the current disc (DVD/CD).
Start address is DVD = 0x030000 or CD =
00:02:00.
00:02:00.
[4] Pause
: Pause
[5] Stop
: Stop
Note: After Search Disc, hold on in 10 seconds.
Click on the first or last page to see other DVP-NS3100ES service manuals if exist.