Sony SAL24105 Service Manual ▷ View online
HELP
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
HELP03
Cut the polyester tapes (black) 10mm as instructed in the figure.
Affix the brush cover and zoom ring reinforcement plate with the polyester tapes (black) 10mm as shown in the figure.
HELP04
After adjusting the zoom brush position adjustment, affix the polyester tapes (black) 10mm cut as instructed to the position shown in the
figure.
Note:
For zoom brush position adjustment, refer to P.4-30.
Brush Cover
Polyester Tape (Black) 10mm
(8x25mm)
(8x25mm)
Polyester Tape (Black) 10mm
(8x25mm)
(8x25mm)
Zoom Ring Reinforcement Plate
Zoom Control Tube
Zoom Control Tube
Zoom Brush
Polyester Tape (Black) 10mm
(6x50mm)
(6x50mm)
HELP
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
HELP05
Adhesive bond (LOCTITE 460)
Note:
Use the adhesive bond (LOCTITE 460) or the equivalent.
Do no use other adhesive bond such as the instantaneous glue that becomes whitish after dried.
Anti-diffusion agent (A-20): J-6082-611-A
Grease (G-85):
J-6082-626-A
1.
Apply the adhesive bond (LOCTITE 460) to the indicated portions of mount index and insert it in the specified hole of zoom hold
ring.
2.
Apply the anti-diffusion agent (A-20) to the entire circumference of indicated portion of zoom hold ring.
3.
Apply the grease (G-85) to the indicated portions (two locations) of zoom hold ring.
HELP06
Adhesive bond (B-40): J-6082-614-A
Apply the adhesive bond (B-40) to the tips of three screws and tighten them as shown in the figure.
Apply the grease (G-85)
Zoom Hold Ring
Mount Index
Apply the LOCTITE 460
Apply the anti-diffusion agent (A-20)
(Entire circumference)
(Entire circumference)
Screw Hole
Screw Hole
Mount Index
Screw Hole
Apply the adhesive bond (B-40)
Apply the adhesive bond (B-40)
HELP
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
HELP07
Adhesive bond (LOCTITE 460)
Note:
Use the adhesive bond (LOCTITE 460) or the equivalent.
Do no use other adhesive bond such as the instantaneous glue that becomes whitish after dried.
Grease (G-85):
J-6082-626-A
Anti-diffusion agent (A-20): J-6082-611-A
1.
Apply the grease (G-85) to the indicated portions (three locations) of lens mount block.
2.
Apply the anti-diffusion (A-20) to the entire circumference of indicated portion of lens mount block.
3.
Insert the preset ring guide assy in the iris control plate and attach the main SP guide riveting block.
Lens Mount Block
Stopper Screw
Apply the anti-diffusion agent (A-20)
Apply the adhesive bond (G-85)
Apply the LOCTITE 460
Iris Control Tube
HELP
SAL24105 (3.5-4.5/24-105) (24-105mm F3.5-4.5)
HELP08
Hook the main spring to the lens mount block and preset ring guide assy as shown in the figure.
Note:
Hook one where hole diameter of coil of main spring is small for the lens mount block, hook one where hole diameter of coil of
main spring is large for the preset ring guide assy.
HELP09
Grease (G-15): J-6082-619-A
Grease (G-85): J-6082-626-A
1.
Apply the grease (G-15) to the indicated portions of AF coupler shaft and gear (C, D) block.
2.
Apply the grease (G-85) to the shaft of gear (C, D) block.
HELP10
Apply the anti-diffusion agent (A-20) to the entire circumference of indicated portion of 4 group lens block.
Hole Diameter (small)
Hole Diameter (large)
Preset Ring Guide Assy
Lens Mount Block
Main Spring
Hook
Apply the grease (G-15)
Apply the grease (G-85)
AF Coupler Shaft
Coupler Adjustment Washer
Gear (C, D) Block
Apply the anti-diffusion agent (A-20)
4 group Lens Block
Click on the first or last page to see other SAL24105 service manuals if exist.