Sony SAL18250 Service Manual ▷ View online
HELP
SAL18250 (3.5-6.3/18-250) (DT 18-250mm F3.5-6.3)
HELP
Note for assembling and grease applying positions are shown.
HELP01-01
Adhesive bond (B-10): J-6082-612-A
1.
After the focus-shift adjustment, apply the adhesive bond (B-10) to indicated portion as shown in figure.
2.
Confirm the position of filter screw frame and tighten it with three screws.
3.
Assemble the decoration ring, aligning its position.
Apply the adhesive
bond (B-10)
bond (B-10)
1st Lens Barrel Assy
Main Assy
1st Lens Barrel Assy
After Focus-Shift Adjustment
Screw
Decoration
Ring
Ring
Decoration Ring
Filter Screw
Flame
Flame
Filter Screw Flame
Oblong Hole
Oblong Hole
Round Hole
Boss
Boss
Boss
Notch
Screw
Screw
1st Lens Slip Barrel
Index (1st Lens Slip Barrel)
HELP
SAL18250 (3.5-6.3/18-250) (DT 18-250mm F3.5-6.3)
Main Assy
Screws
Screws
a
d
b
c
Mount Assy
Back Adjusutment
washer
washer
Coupler
Coupler Bush
Coupler
Apply the grease (G-36)
(Dip thoroughly)
(Dip thoroughly)
Apply the grease (G-36)
(Dip thoroughly)
(Dip thoroughly)
Apply the grease (G-100)
(Pointed end of coupler)
(Pointed end of coupler)
Apply the grease (G-37)
(Mount Side)
(Mount Side)
HELP01-02
Grease (G-36):
J-6082-667-A
Grease (G-37):
J-6082-668-A
Grease (G-100): J-6082-664-A
1.
Apply the grease (G-37) to the indicated portion of back adjustment washer.
Note:
Apply the grease only to the washer that contacts the coupler.
2.
Apply the coupler bush in the grease (G-36), apply the grease (G-100) to the indicated portion of coupler and assemble the coupler.
3.
Apply the coupler nearing in the grease (G-36) and assemble it to the mount assy.
4.
Tighten the coupler bearings to the mount assy with four screws.
Note:
Tighten four screws in order of a
t b t c t d t a.
HELP
SAL18250 (3.5-6.3/18-250) (DT 18-250mm F3.5-6.3)
HELP01-03
Adhesive bond (LOCTITE 460)
Note:
Use the bond (LOCTITE 460) or the equivalent.
Do not use the instant glue that becomes white after dried.
1.
Apply the adhesive bond (LOCTITE 460) to the rear lens barrel assy and affix the mount index.
Note:
Be careful not to apply too much bond. Be careful for the bond not to seep out.
2.
Set the focus to near position.
3.
Thread the Z.ECD and F.ECD flexible board through the hole of rear lens barrel assy and fix them with five screws.
Note:
Tighten five screws in order of a
t b t c t d t e t a.
Main Assy
Rear Lens
Barrel Assy
Barrel Assy
Screw
Screws
d
b
Taking out hole of the
Z.ECD Flexible Board
Z.ECD Flexible Board
Taking out hole of the
F.ECD Flexible Board
F.ECD Flexible Board
c
a
e
Screws
Mount Index
Apply the Adhesive Bond
(LOCTITE460)
(LOCTITE460)
Set the focus to
near position.
near position.
Two Flexible Board
2-5
SAL18250 (3.5-6.3/18-250) (DT 18-250mm F3.5-6.3)
2-2-2. ZOOM RING ASSY, MIDDLE LENS BARREL ASSY AND OUTER BARREL
A
B
B-40
Turn over the
Focus Rubber
Focus Rubber
HELP02-03
HELP02-01
HELP02-02
4
HELP02-06
8
HELP02-05
HELP02-04
6
5
7
1
3
2
Middle Lens
Barrel Assy
Barrel Assy
Focus Linkage
Support Plate
Support Plate
Zoom Linkage
Post
Post
Focus Coupling
Plate
Plate
Focus Brush
Zoom Ring Assy
Zoom Linkage
Coma B
Coma B
Brush part
(Zoom Brush)
(Zoom Brush)
Cover part
(Zoom Brush)
(Zoom Brush)
Setting Tape B
Brush Tape
Zoom Rubber
2-2-1.
ZOOM BRUSH
POSITION
ADJUSTMENT
POSITION
ADJUSTMENT
FOCUS BRUSH
POSITION
ADJUSTMENT
POSITION
ADJUSTMENT
EXPLODED VIEW
(See page 2-6.)
(See page 2-6.)
(From page 2-4.)
Focus
Coupling
Plate
Coupling
Plate
Click on the first or last page to see other SAL18250 service manuals if exist.