Sony SAL1118 Service Manual ▷ View online
4-18
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
4-6.
ZOOM BRUSH POSITION CHECK/ADJUSTMENT AND PATTERN CHECK
Note:
If dialog box of error code appears during the checking or adjustment, check the reason of error referring to page 4-22.
4-6-1. Zoom Brush Position Check
Equipment
• Personal Computer (PC)
• Camera DSLR-A100
• USB Cord With Connector
• Lens Adjustment Program
Note:
Lens Adjustment Program is downloadable from the ESI homepage.
1. Preparations
1)
Connect the checking lens to the camera.
2)
Start the lens adjustment program “LensAdjustment.exe” referring to “4-1-2. Lens Adjustment Program”.
Fig. 4-6-1
2. Checking Method
1)
Click the
[Connect]
button on the lens adjustment program.
Note:
Click the
[End]
button to disconnect the USB connection, then lens adjustment program will terminate.
Fig. 4-6-2
2)
Click the
[Zoom]
button on the lens adjustment program.
3)
Set the zoom position to Tele end, and check that the OK (Green) indicator of “Position” lights as shown in Fig. 4-6-3.
Note:
Lens focus position setting is not required.
Fig. 4-6-3
If the NG (Red) indicator of “Position” lights, check zoom brush and frekipattern is confirmed.
Fig. 4-6-4
4)
Click the
[Exit]
button.
5)
Click the
[End]
button to terminate the lens adjustment program.
6)
Turn the POWER switch of the camera to OFF.
Ver 1.3 2007.04
4-19
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
4-6-2. Zoom Brush Position Adjustment and Pattern Check
Equipment
• Personal Computer (PC)
• Camera DSLR-A100
• USB Cord With Connector
• Adhesive Bond (B-10)
• Lens Adjustment Program
Note:
Lens Adjustment Program is downloadable from the ESI homepage.
1. Preparations
1)
Remove the zoom lens and brush cover.
2. Zoom Brush Position Adjustment
1)
Set the zoom position to Tele end.
2)
Perform the “4-6-1. Zoom Brush Position Check”, and adjustment to Brush Position until the OK (Green) indicator of “Position”
lights, and fixed with the double-faced tape after adjusting.
Fig. 4-6-5
3. Pattern Check
Note:
When the NG (Red) indicator of “Position” lights during checking, does not care about it (It is normal performance).
1)
Turn the zoom ring slowly from the Wide end “Zoom Pattern : 1” to Tele end “Zoom Pattern : 20” and check that the value of “Zoom
Pattern” change from 1 to 20 continuously.
2)
Turn the zoom ring slowly from Tele end (Zoom Pattern : 20) to the Wide end (Zoom Pattern : 1) and check that the value of “Zoom
Pattern” change from 20 to 1 continuously.
Fig. 4-6-6
3)
Click the
[Exit]
button.
4)
Click the
[End]
button to terminate the lens adjustment program.
5)
Turn the POWER switch of the camera to OFF.
h
h
h
h
h
4-20
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
4-7.
FOCUS BRUSH POSITION AND PATTERN CHECK
Note:
If dialog box of error code appears during the checking or adjustment, check the reason of error referring to page 4-22.
4-7-1. Focus Brush Position Check
Equipment
• Personal Computer (PC)
• Camera DSLR-A100
• USB Cord With Connector
• Lens Adjustment Program
Note:
Lens Adjustment Program is downloadable from the ESI homepage.
1. Preparations
1)
Connect the checking lens to the camera.
2)
Start the lens adjustment program “LensAdjustment.exe” referring to “4-1-2. Lens Adjustment Program”.
Fig. 4-7-1
2. Checking Method
1)
Click the
[Connect]
button on the lens adjustment program.
Note:
Click the
[End]
button to disconnect the USB connection, then lens adjustment program will terminate.
Fig. 4-7-2
2)
Click the
[Focus]
button on the lens adjustment program.
3)
Set the zoom position to Wide end and the focus position to infinity end, then check that the OK (Green) indicator of “Position”
lights as shown in Fig. 4-7-3.
Fig. 4-7-3
If the NG (Red) indicator of “Position” lights, then check that Focus Brush Position.
Fig. 4-7-4
4)
Click the
[Exit]
button.
5)
Click the
[End]
button to terminate the lens adjustment program.
6)
Turn the POWER switch of the camera to OFF.
Ver 1.3 2007.04
4-21
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
h
h
h
h
h
4-7-2. Focus Brush Position Adjustment and Pattern Check
Equipment
• Personal Computer (PC)
• Camera DSLR-A100
• USB Cord With Connector
• Adhesive bond (B-10)
• Lens Adjustment Program
Note:
Lens Adjustment Program is downloadable from the ESI homepage.
1. Pattern Check
Note:
When the NG (Red) indicator of “Position” lights during checking, does not care about it (It is normal performance).
1)
Turn the focus ring slowly from the near end “Focus Pattern : 1” to the infinity end “Focus Pattern : 19” and check that the value of
“Focus Pattern” change from 1 to 19 continuously.
2)
Turn the focus ring slowly from the infinity end “Focus Pattern : 19” to the near end “Focus Pattern : 1” and check that the value of
“Focus Pattern” change from 19 to 1 continuously.
Fig. 4-7-5
3)
Click the
[Exit]
button.
4)
Click the
[End]
button to terminate the lens adjustment program.
5)
Turn the POWER switch of the camera to OFF.
Click on the first or last page to see other SAL1118 service manuals if exist.