Sony SAL1118 Service Manual ▷ View online
HELP
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
HELP14
Anti-diffusion agent (A-20): J-6082-611-A
Grease (G-85):
J-6082-626-A
1.
Apply anti-diffusion agent (A-20) and grease (G-85) to the instruction portions of the outer barrel assy and focus gear barrel.
2.
Assemble the outer barrel assy and focus gear barrel so that the projection of the focus gear barrel fit to the notch of the outer barrel
assy.
Focus Gear Barrel
Projection
Notch
Outer Barrel Assy
Focus Gear Barrel
Apply grease (G-85)
(all circumference of gear)
(all circumference of gear)
Apply anti-diffusion agent (A-20) (all circumference)
Outer Barrel Assy
Apply grease (G-85)
(all circumference of gear)
(all circumference of gear)
Apply anti-diffusion agent (A-20)
(all circumference)
(all circumference)
HELP
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
3.
Turn the cam barrel to arrow direction to set the “Wide” end.
4.
Set the focus gear barrel to near end position.
5.
Assemble the length groove barrel and outer barrel assy so that the projection of the outer barrel assy fit to the notch of the length
groove barrel.
Cam Barrel
Focus Gear Barrel
Notch
Projection
Outer Barrel Assy
Length Groove Barrel
HELP
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
HELP15
1.
Install the focus brush so that the tips of it contact to the focus flex patterns, and apply adhesive bond (B-10) to the two screws and
then tighten them as shown in the figure.
Adhesive bond (B-10): J-6082-612-A
2.
Perform the “4-7. Focus Brush Position/Pattern Check”.
HELP16
1.
Apply grease (G-15) to the instruction portions of the zoom ring.
Grease (G-15): J-6082-619-A
2.
Turn the zoom ring to align the hole of the zoom ring with the screw hole of the zoom stopper as shown in the figure.
Focus Brush
Apply adhesive bond (B-10) (Two screws)
Apply grease (G-15) (all circumference)
Hole
Zoom Stopper
Zoom Ring
3-1
SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)
12
6
7
19
22
17
18
12
12
23
25
26
4
1
3
1
5
28
27
2
2
5
2
5
9
15
14
15
10
13
(See page 2-2.)
A
B
B
21
(Note 1)
26
26
24
24
19
20
29
16
8
(
6 x 10 mm)
(Note 2)
(
6 x 10 mm)
(Note 2)
11
A
(Note 1)
(7 x 100 mm)
(Note 3)
(Note 3)
(7 x 100 mm)
(Note 3)
(Note 3)
8
3. REPAIR PARTS LIST
3-1.
EXPLODED VIEWS
3-1-1. REAR LIGHT SHIELD BARREL, MOUNT SET AND REAR LENS BARREL ASSY
DISASSEMBLY
Ref. No.
Part No.
Description
1
2-886-755-01 SCREW (2P1.7X5.5C3C IB LOCK)
2
2-886-756-01 SCREW (2P1.7X3.5C3C IB LOCK)
3
Selection parts 1ST LENS WASHER (Note 1)
4
2-886-758-01 FILTER SCREW FRAME
5
2-886-757-01 ADJUSTMENT SPRING
6
A-1206-680-A 1ST LENS BARREL ASSY
7
2-886-754-01 DECORATING RING
8
2-649-300-01 SHEET, ADHESIVE (Note 2)
9
2-886-790-01 SCREW (BT 2P1.7X3C3C)
10
2-886-764-01 ZOOM RUBBER
11
A-1206-682-A REAR LENS BARREL ASSY
12
2-886-766-01 SCREW (BT2P1.7X4.5C3C)
13
2-886-765-01 NUMBER SEAL
14
A-1206-681-A GEAR BASE PLATE ASSY
15
9-913-210-01 INSULATING TAPE (Note 3)
NOTE:
•
-XX and -X mean standardized parts, so they may
have some difference from the original one.
have some difference from the original one.
•
Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
seldom required for routine service. Some delay
should be anticipated when ordering these items.
•
The mechanical parts with no reference number in
the exploded views are not supplied.
the exploded views are not supplied.
16
2-886-763-01 ZOOM BRUSH
17
2-886-762-01 BRUSH COVER
18
2-886-761-01 FOCUS RUBBER
19
A-1206-683-A MAIN PCB ASSY
20
2-886-767-01 SCREW (BT2P1.7X3C3C)
21
Selection parts BACK ADJUSTMENT WASHER (Note 1)
22
A-1206-684-A MOUNT ASSY
23
2-886-792-01 SCREW (BT101.7X4GR301)
24
2-886-789-01 SCREW (2P1.4X2.2GR301)
25
2-886-788-01 REAR LIGHT SHIELD BARREL
26
2-886-791-01 SCREW (BT1P2X6C3C)
27
2-886-787-01 COUPLER RECEIVE
28
2-886-786-01 COUPLER
29
2-683-692-01 CHIP (MOUNT INDEX)
Ref. No.
Part No.
Description
(Note 1)
The number or type of these parts need to be selected
according to adjustment etc..
Select the part referring to page 3-3.
according to adjustment etc..
Select the part referring to page 3-3.
(Note 3)
Cut the insulating tape (Ref. No. 15) for 7
×100 mm.
(Note 2)
Cut the adhesive sheet (Ref. No. 8) for 6
×10 mm.
Ver 1.2 2007.03
Click on the first or last page to see other SAL1118 service manuals if exist.