Sony NEX-3 / NEX-3A / NEX-3D / NEX-3K / NEX-5 / NEX-5A / NEX-5CK / NEX-5D / NEX-5H / NEX-5K (serv.man2) Service Manual ▷ View online
NEX-3A/3D/3K/5A/5D/5CD/5K/5CK/5H_L2
3-4
Hold here
Assembly-28: MB N Contact Unit holding position
MB N Contact Unit
Insert IS-075 Flexible Board into the connector on
IM Imager Unit 14M, then lock the connector.
Assemble Heat Sink and IM Imager Unit 14M.
Note: IS-075 Flexible Board can not be inserted after
assembling Heat Sink.
Heat Sink
IM Imager Unit 14M
IS-075 Flexible Board
Assembly-30: Prior
Insertion of IS-075 Flexible Board
(NEX-3A/3D/3K)
Radiation Sheet (IS)
Heat Sink
Without running off the
edge of the hole.
Without running on the
edge of Heat Sink.
Assembly-31: Radiation
Sheet (IS) putting position
SY-258 Complete Board
CN-439 Complete Board
Put the surplus part of the
shutter flexible board under
SY-258 Complete Board.
Assembly-32: How to handle the Shutter Flexible Board
(NEX-3A/3D/3K)
Assembly-29: Note when assembling Heat Sink
Align with the positioning hole.
Heat Sink
CN-439
Complete Board
LC Connector
Insulating Sheet
BT Frame Assy
Within 0.5mm
Within 0.5mm
Assembly-33: LC Connector
Insulating Sheet
putting position
Assembly-34: Tape AS (210) putting position
(NEX-5A/5D/
5CD
/5K/5CK/
5H
)
Tape AS (210)
Without protruding
from the rib top surface.
Without running off
the mask sheet.
Without running on this boss.
Assembly-35: Method of attachment of LC Flexible
Insulating Sheet
(NEX-3A/3D/3K)
Bend the LC Flexible Insulating Sheet along
the curve of BT-063 Flexible Board.
LC Flexible
Insulating Sheet
±1.0mm
The changed portions from
Ver.1.4 are shown in blue.
Ver.1.5 2011.01
NEX-3A/3D/3K/5A/5D/5CD/5K/5CK/5H_L2
3-5E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1 Souse the one cleaning cloth in ethyl alcohl.
2 Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
1
Souse the cleaning
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310
NEX-3A/3D/3K/5A/5D/5CD/5K/5CK/5H_L2
3-5E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1 Souse the one cleaning cloth in ethyl alcohl.
2 Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
1
Souse the cleaning
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310
NEX-3A/3D/3K/5A/5D/5CD/5K/5CK/5H_L2
3-5E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1 Souse the one cleaning cloth in ethyl alcohl.
2 Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
1
Souse the cleaning
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310
