DOWNLOAD Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) Service Manual ↓ Size: 4.36 MB | Pages: 17 in PDF or view online for FREE

Model
NEX-5N NEX-5ND NEX-5NK NEX-5NY (serv.man2)
Pages
17
Size
4.36 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
nex-5n-nex-5nd-nex-5nk-nex-5ny-sm2.pdf
Date

Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) Service Manual ▷ View online

NEX-5N/5ND/5NK/5NY_L2
Sony Corporation
SERVICE MANUAL
Revision History
SERVICE  NOTE (Check the following note before the service.)
LEVEL 
2
983459833.pdf
2012K08-1
© 2012.11
Published by Sony Techno Create Corporation
Ver. 1.2  2012.11
INTERCHANGEABLE LENS DIGITAL CAMERA
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
Korea Model
Japanese Model
Tourist Model
1-1. 
PRECAUTION ON REPLACING THE SY-292 BOARD
9-834-598-33
Photo: NEX-5N/Black
[About the service of this model]
NEX-5ND/5NK/5NY are commodity that packed the Interchangeable Lens Digital Camera and Interchangeable Lenses.
Refer to each following service manual the Interchangeable Lens kit, when you repair.
Model
Lens
Service Manual of Lens
NEX-5N
No supplied lens
No supplied lens
NEX-5ND
SEL16F28 (E 16mm F2.8)
9-852-798-1[]
SEL1855 (E 18-55mm F3.5-5.6 OSS)
9-852-799-1[]
NEX-5NK
SEL1855 (E 18-55mm F3.5-5.6 OSS)
9-852-799-1[]
NEX-5NY
SEL1855 (E 18-55mm F3.5-5.6 OSS)
9-852-799-1[]
SEL55210 (E 55-210mm F4.5-6.3 OSS)
9-834-603-1[]
– ENGLISH –
– JAPANESE –
1-1. 
SY-292基板交換時の注意
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2011.08
Official Release
1.1
2011.11
Revised-1
(A1 11-285)
•  Change of EXPLODED VIEWS.
 Page 
2-7
Yes
1.2
2012.11
Revised-2
(A2 12-278)
• Addition of ACCESSORIES.
 Page 
2-10
Yes
The components identified 
by mark 
0 or dotted line with 
mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques 
pour la sécurité.
Ne les remplacer que par une 
pièce portant le numéro spécifié.
NEX-5N/5ND/5NK/5NY
Revised-2
Replace the previously issued
SERVICE MANUAL 9-834-598-32
with this Manual.
NEX-5N/5ND/5NK/5NY_L2
– 2 –
SPECIFICATIONS
– ENGLISH –
– JAPANESE –
概略仕様
本体
[形式]
カメラタイプ:レンズ交換式デジタルカメラ
使用レンズ:
E
マウントレンズ
[撮像部]
イメージセンサー:
23.5 
×
 15.6 mm
APS-C
サイズ)、
CMOS
イメージセンサー
総画素数:約
16 700 000
画素
カメラ有効画素数:約
16 100 000
画素
[アンチダスト]
システム:帯電防止コートおよび超音波
振動によるアンチダスト機能
[オートフォーカス]
形式:コントラスト検出方式
検出輝度範囲:
EV0 
 EV20 
ISO 100
相当、
F2.8
レンズ使用時)
[露出制御]
測光方式:イメージセンサーによる
1 200
分割測光
測光範囲:
EV0 
 EV20 
ISO 100
相当、
F2.8
レンズ使用時)
ISO
感度(推奨露光指数):オート、
ISO100 
 25600
露出補正:±
3.0 EV 
1/3
段ステップ)
[シャッター]
形式:電子制御式縦走りフォーカルプ
レーンシャッター
シャッタースピード範囲:
1/4000 
30
秒、バルブ(
1/3
段ステップ)
フラッシュ同調速度:
1/160
[記録メディア]
“メモリースティック
 PRO 
デュオ”、
SD
カード
[液晶モニター]
形式:
7.5 cm 
3.0
型)
 TFT
駆動
ドット数:
921 600 
640
×
RGB
)×
480
)ドット
[入出力端子]
USB
端子:
miniB
HDMI
端子:
HDMI
タイプ
C
ミニ端子
[電源]
バッテリー:リチャージャブルバッテ
リーパック
NP-FW50
[その他]
Exif Print
:対応
PRINT Image Matching III
:対応
外形寸法(
CIPA
準拠):
110.8
×
58.8
×
38.2 mm
(幅×高さ×奥行き)
本体質量(
CIPA
準拠):
269 g 
(バッテリー、“メモリース
ティック
 PRO 
デュオ”を含む)
210 g 
(本体のみ)
動作温度:
0
℃∼
 40
記録方式:
静止画記録方式:
JPEG
DCF Ver.2.0
Exif Ver.2.3
MPF Baseline
)準拠、
DPOF
対応
3D
静止画記録方式:
MPO
MPF
Extended
(立体視))準拠
動画記録方式(
AVCHD
ビュー):
AVCHD
規格(
1080 60p/
独自規格)
映像:
MPEG-4 AVC/H.264
音声:
Dolby Digital 2ch
ドルビーデジタルステレオクリエー
ター搭載
   
 
ドルビーラボラトリーズからの実施権に
基づき製造されています。
 
動画記録方式(
MP4
ビュー):
MP4
方式
映像:
MPEG-4 AVC/H.264
音声:
MPEG-4 AAC-LC 2ch
USB
通信:
Hi-Speed USB 
USB2.0
バッテリーチャージャー
BC-VW1
定格入力:
AC100 V – 240 V
50 Hz/60 Hz
4.2 W
定格出力:
DC 8.4 V
0.28 A
動作温度:
0
℃∼
 40
保存温度:−
20
℃∼+
60
最大外形寸法:約
63
×
95
×
32 mm
(幅×高さ×奥行き)
本体質量:約
85 g
リチャージャブルバッテリー
パックNP-FW50
使用電池:リチウムイオン蓄電池
最大電圧:
DC 8.4 V
公称電圧:
DC 7.2 V
容量:公称容量
 7.7 Wh
1 080 mAh
定格(最小)容量:
7.3 Wh
1 020 mAh
最大外形寸法:約
31.8
×
18.5
×
45 mm
(幅×高さ×奥行き)
本体質量:約
57 g
本機や付属品の仕様および外観は、改良
のため予告なく変更することがあります
が、ご了承ください。
Camera
[System]
Camera type: Interchangeable lens digital camera
Lens: E-mount lens
[Image sensor]
Image sensor: 23.5 × 15.6 mm (APS-C format) 
CMOS image sensor
Total pixel number of image sensor:
Approx. 16 700 000 pixels
Effective pixel number of camera:
Approx. 16 100 000 pixels
[Anti-dust]
System: Charge protection coating on Low-Pass 
Filter and ultrasonic vibration mechanism
[Auto focus system]
System: Contrast detection system
Sensitivity range: EV0 to EV20 (at ISO 100 
equivalent, with F2.8 lens)
[Exposure control]
Metering method: 1 200-segment metering 
by the image sensor
Metering range: EV0 to EV20 (at ISO 100 
equivalent, with F2.8 lens)
ISO sensitivity (Recommended exposure index): 
Auto, ISO 100 to 25600
Exposure compensation: ±3.0 EV (1/3 EV step)
[Shutter]
Type: Electronically-controlled,
vertical-traverse, focal-plane type
Speed range: 1/4000 second to 30 seconds, 
BULB, (1/3 EV step)
Flash sync speed: 1/160 second
[Recording media]
“Memory Stick PRO Duo” media, 
SD card
[LCD monitor]
LCD panel: 7.5 cm (3.0 type) TFT drive
Total number of dots: 
921 600 (640 × 3 (RGB) × 480) dots
[Input/output terminals]
USB: miniB
HDMI: HDMI type C minijack
[Power]
Used battery pack: 
Rechargeable battery pack NP-FW50
[Others]
Exif Print: Compatible
PRINT Image Matching III: Compatible
Dimensions (CIPA compliant):
Approx. 110.8 × 58.8 × 38.2 mm
(4 3/8 × 2 3/8 × 1 9/16 inches)
(W/H/D)
Mass (CIPA compliant):
Approx. 269 g (9.5 oz)
(including battery and “Memory
Stick PRO Duo” media)
Approx. 210 g (7.4 oz)
(camera only)
Operating temperature: 0°C to 40°C
(32°F to 104°F)
File format:
Still image: JPEG (DCF Ver. 2.0,
 
Exif Ver. 2.3, MPF Baseline)
 
compliant, DPOF compatible
 
3D still images: MPO (MPF
 
Extended (Disparity Image))
 compliant
 Movie 
(AVCHD 
View):
 
AVCHD format (1080 60p or
 
1080 50p, original format)
 Video: 
MPEG-4 
AVC/H.264
 
Audio: Dolby Digital 2ch
 
Dolby Digital Stereo Creator
 
•  Manufactured under license from
Dolby Laboratories.
 
Movie (MP4 View): MP4 format
 Video: 
MPEG-4 
AVC/H.264
 
Audio: MPEG-4 AAC-LC 2ch
USB communication: Hi-Speed USB
(USB 2.0)
Battery charger BC-VW1
Input rating: 100 V – 240 V AC,
 
50Hz/60 Hz, 4.2 W
Output rating: 8.4 V DC, 0.28 A
Operating temperature range: 0°C to 40°C 
(32° to 104°F)
Storage temperature range: –20°C to +60°C 
(–4°F to +140°F)
Maximum dimensions: 
Approx. 63 × 95 × 32 mm 
(2 1/2 × 3 3/4 × 1 5/16 inches) 
(W/H/D)
Mass: Approx. 85 g (3 oz)
Rechargeable battery pack
NP-FW50
Used battery: Lithium-ion battery
Maximum voltage: DC 8.4 V
Nominal voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
 
Minimum 7.3 Wh (1 020 mAh)
Maximum dimensions:
 
Approx. 31.8 × 18.5 × 45 mm
 
(1 5/16 × 3/4 × 1 13/16 inches)
 (W/H/D)
Mass: Approx. 57 g (2.1 oz)
Design and specifications are subject to
change without notice.
Model information table
Model
NEX-5N
NEX-5ND
NEX-5NK
NEX-5NY
Destination
US, AEP, UK, E, KR, 
AUS, CH, J
AEP, UK, E, KR, 
AUS, CH, JE, J
US, CND, AEP, UK, E, 
AUS, CH, KR, J
AEP, UK, E, KR, 
AUS, CH, J
Lens
E 16mm F2.8 / 
E 18-55mm F3.5-5.6 OSS
E 18-55mm F3.5-5.6 OSS
E 18-55mm F3.5-5.6 OSS / 
E 55-210mm F4.5-6.3 OSS
• Abbreviation
  AUS :  Australian model
  CH :   Chinese model
  CND :  Canadian model
  J : 
Japanese model
  JE : 
Tourist Model
  KR :   Korea model
NEX-5N/5ND/5NK/5NY_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Caution
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health 
and environment, and wastes resources.
Manage the chemicals carefully as follows.
•  Store chemicals sealed in a specific place to prevent from exposure 
to high temperature or direct sunlight.
•  Avoid dividing chemicals into excessive numbers of small containers 
to reduce natural evaporation.
•  Keep containers sealed to avoid natural evaporation when chemicals 
are not in use.
•  Avoid using chemicals as much as possible. When using chemicals, 
divide only required amount to a small plate from the container and 
use up it.
EXTERIOR  PARTS
Be careful to the following points for plastic parts used in this unit.
•  Use a piece of cleaning paper or cleaning cloth for cleaning plastic 
parts. Avoid using chemicals.
 
Even if you have to use chemicals to clean heavy dirt, don’t use paint 
thinner, ketone, nor alcohol.
•  Insert the specific screws vertically to the part when installing a 
plastic part.
 
Be careful not to tighten screws too much.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
各種薬品の取り扱いについて
現在使用されている薬品の中には揮発性の高い薬品もありま
す。
それらを不用意に取り扱い蒸発させてしまうと,環境や健康へ
影響を与えたり,資源の無駄使いになります。
各種薬品は,下記の点に注意して取り扱ってください。
・  保管場所を定め,高温になったり直射日光の当たらない場
所に密閉して保管してください。
・  小分け(ハンドラップ等)する数は必要最小限に留め,容器
による自然蒸発を防いでください。
・  作業に使用しない時は,必ずキャップ等をして自然蒸発を
防いでください。
・  薬品を使用する回数を極力少なくし,使用する場合は使用
する量だけ容器より出して受け皿に残さないようにしてく
ださい。
樹脂系部品の取り扱いについて
本機に使用されている樹脂系の部品は,下記の点に注意して取
り扱ってください。
・  清掃には薬品を使用せず,清掃紙や清掃布を使用してくだ
さい。
 
やむを得ず汚れがひどくて薬品を使用する場合は,シン
ナー,ケトン,エーテルは使用しないでください。
・  各部品の取り付けには指定されたねじを使用し,部品に対
して垂直に取り付けてください。
 
また,ねじを締め付ける時は,無理な力を加えないでくだ
さい。
サービス,点検時には次のことにご注意ください。
– ENGLISH –
– JAPANESE –
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Keep the temperature of the soldering iron around 350°C during 
repairing.
 
•   Do not touch the soldering iron on the same conductor of the circuit 
board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering or 
unsoldering.
UNLEADED  SOLDER
This unit uses unleaded solder. 
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•  Set the soldering iron tip temperature to 350°C approximately.
 
If cannot control temperature, solder/unsolder at high temperature 
for a short time.
 
Caution: The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!
 
 
Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.
•  Be sure to control soldering iron tips used for unleaded solder and 
those for leaded solder so they are managed separately. Mixing 
unleaded solder and leaded solder will cause detachment phenom-
enon.
1.  注意事項をお守りください。
 
サービスのとき特に注意を要する個所については,キャビ
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書きおよび取扱説明書等の
注意事項を必ずお守りください。
2.  指定部品のご使用を
 
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用してください。特に回路図,
部品表に0印で指定されている安全上重要な部品は必ず指
定のものをご使用ください。
3.  部品の取付けや配線の引きまわしはもとどおりに
 
安全上,チューブやテープなどの絶縁材料を使用したり,
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので,これらは必
ずもとどおりにしてください。
4.  サービス後は安全点検を
 
サービスのために取外したネジ,部品,配線がもとどおり
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認してください。
5.  チップ部品交換時の注意
 
・ 取外した部品は再使用しないでください。
 
・ タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意してください。
6.  フレキシブルプリント基板の取扱いについて
 
・ こて先温度を約350℃に設定して行ってください。
 
・ 同一パターンに何度もこて先を当てないでください。
 
  (3回以内)
 
・ パターンに力が加わらないよう注意してください。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
(注意:  基板サイズによっては,無鉛半田を使用していても
レッドフリーマークがプリントされていないものがあ
ります)
:レッドフリーマーク
無鉛半田は,下記の点に注意して使用してください。
・  半田こてのこて先温度は約350℃に設定してください。
 
温度調節が無理な場合は,高温短時間で作業を行ってくだ
さい。
 
注意: 
半田こてを長く当てすぎると,基板のパター
ン(銅箔)がはがれてしまうことがありますので,注
意してください。また,従来の半田よりも粘性が強
いため,IC端子などが半田ブリッジしないように注
意してください。
・  半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け
て管理してください。
 
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
NEX-5N/5ND/5NK/5NY_L2
1-1
1. SERVICE  NOTE
1-1.  PRECAUTION ON REPLACING THE SY-292 BOARD
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
USB Serial No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
1-2.  PRECAUTION ON REPLACING THE CABINET FRONT
Perform the following procedures for each of the three washers.
Note: Measure the dimensions before replacement of the Cabinet Front according to procedures (1) to (3).
(1) Remove the Imager Block Assy and the IM Adjust Washers (A, B, C).
(2) Measure the dimensions (A) of the removed IM Adjust Washers.
A
+
B
BA
(3) Measure the distance (B) between the surface of the screw hole where the IM Adjust Washers were set and the surface of the E-Mount.
(4) Likewise, measure the dimensions (B’) of each location where IM Adjust Washers of new Cabinet Front are installed.
(5) Calculate the dimension of (A’) of new IM Adjust Washer by using the formula below, and select the washers.
  
Dimension 
(A+B) before replacement – Dimension (B’) of new Cabinet Front
           
= Dimension (A’) of IM Adjust Washer after replacement
(6) Assemble the imager, using the selected IM Adjust Washers.
(7) After assembling is completed, perform the test shooting and confirm that no blur is observed in the peripheral area of shot.
– ENGLISH –
1-3.  ABOUT THE FLASH EXTENDER (NEX-5NY ONLY)
If you attach the flash directly to the camera when using SEL55210 (E 55-210mm F4.5-6.3 OSS), images will be partly shadowed by the lens.
To prevent shadowing, attach the extender.
Extender
A-1787-305-A
Case, EX
4-199-652-01
To attach the extender
(1) Turn the camera off before attaching the extender.
(2) Attach the extender firmly to the camera and tighten the screw.
(3) Attach the flash firmly to the extender and tighten the screw.
Note: Only attach the flash supplied with your camera to the extender.
Page of 17
Display

Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) Service Manual ↓ Size: 4.36 MB | Pages: 17 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) Digital Camera. Information contained in Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.