DSC-W330 (serv.man2) — Sony Digital Camera Service Manual (repair manual)

Model
DSC-W330 (serv.man2)
Pages
29
Size
5.84 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
dsc-w330-sm2.pdf
Date

View Sony DSC-W330 (serv.man2) Service Manual online

DSC-W330_L2
SERVICE MANUAL
Revision History
SERVICE  NOTE (Check the following note before the service.)
LEVEL 
2
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2010.01
Official Release
1.1
2010.01
Revised-1
(A1 09-389)
•  Correction of SERVICE NOTE
 Page 
1-2
•  Correction of EXPLODED VIEWS
 Page 
2-3
2-4
2-5
2-6
•  Correction of SUPPLIED ACCESSORIES
 Page 
2-7
•  Correction of POWER BLOCK DIAGRAM
 Page 
4-2
•  Correction of PRINTED WIRING BOARDS
 Page 
6-5
6-6
Yes
1.2
2010.03
Revised-2
(A2 09-495)
•  Correction of COVER
•  Correction of FRAME SCHEMATIC DIAGRAMS
 Page 
5-1
  (Redeeming the revision history contents of revised-1.)
Yes
1.3
2010.03
Revised-3
(A3 09-534)
•  Revision of SUPPLIED ACCESSORIES
 Page 
2-7
Yes
1.4
2010.08
Revised-4
(A4 10-097)
•  Correction of SERVICE NOTE
 Page 
1-4
1-5
1-7
Yes
Sony Corporation
985274535.pdf
2010H08-1
  © 2010.08
Published by Sony Techno Create Corporation
Ver. 1.4  2010.08
DIGITAL STILL CAMERA
The components identified by 
mark 
0 or dotted line with mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques pour 
la sécurité.
Ne les remplacer que par une piè-
ce portant le numéro spécifié.
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Korea Model
Brazilian Model
1-1.  PRECAUTION ON REPLACING THE SY-243 BOARD
1-2.  METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
1-3.  HOW TO WRITE DATA TO INTERNAL MEMORY
1-4.  POWER SUPPLLY DURING REPAIRS
1-5. SELF-DIAGNOSIS FUNCTION
1-6.  PROCESS AFTER FIXING FLASH ERROR
1-7.  ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
1-8.  OPTICAL STEPING MOTOR (F1380) REPLACING METHOD
1-9.  DC MOTOR WORM A ASSY REPLACING METHOD
1-10. CAM TUBE BLOCK ASSY AND STRAIGHT TUBE LUBRICATED ASSY AND 
1 GROUP FRAME REPLACING METHOD
1-11. FINAL  INSPECTION
Photo: Silver
9-852-745-35
DSC-W330
Replace the previously issued 
SERVICE MANUAL 9-852-745-34 
with this Manual.
Internal memory
ON BOARD
Internal memory
ON BOARD
Revised-4
DSC-W330_L2
– 2 –
SPECIFICATIONS
Camera
[System]
Image device: 7.76 mm (1/2.3 type)
color CCD, Primary color filter
Total pixel number of camera:
Approx. 14.5 Megapixels
Effective pixel number of camera:
Approx. 14.1 Megapixels
Lens: Carl Zeiss Vario-Tessar 4× zoom lens
f = 4.7 mm – 18.8 mm (26 mm – 105 mm 
(35 mm film equivalent))
F2.7 (W) – F5.7 (T)
Exposure control: Automatic exposure,
Scene Selection (10 modes)
White balance: Automatic, Daylight,
Cloudy, Fluorescent 1/2/3,
Incandescent, Flash
Underwater White Balance: Auto,
Underwater 1/2
Recording interval for Burst mode:
Approx. 1.0 second
File format: 
Still images: JPEG (DCF Ver. 2.0,
Exif Ver. 2.21) compliant, DPOF compatible
Movies: AVI (Motion JPEG)
Recording media: Internal Memory
(Approx. 28 MB), “Memory Stick Duo” media, 
SD memory cards,
SDHC memory cards (Class 4, 6,10)
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index) set to Auto):
Approx. 0.3 m to 3.5 m (W)
(11 7/8 inches to 11 feet 5 7/8 inches)
Approx. 0.6 m to 1.8 m (T) (1 foot 11 5/8 inches 
to 5 feet 10 7/8 inches)
[Input and Output connectors]
(USB)/A/V OUT terminal:
Video output
Audio output (Monaural)
USB communication
USB communication: Hi-Speed USB
(USB 2.0 compliant)
[LCD screen]
LCD panel: 
7.5 cm (3.0 type) TFT drive
Total number of dots: 230 400 (960 × 240) dots
[Power, general]
Power: Rechargeable battery pack
NP-BN1, 3.6 V
Power consumption (during shooting):
1.0 W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions: 
95.9 × 56.8 × 17.3 mm 
(3 7/8 × 2 1/4 × 11/16 inches) 
(W/H/D, excluding protrusions)
Mass (including NP-BN1 battery pack,
Memory card):
Approx. 128 g (4.5 oz.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
Compatible
PictBridge: Compatible
BC-CSN/BC-CSNB battery charger
Power requirements: AC 100 V to 240 V, 
50/60 Hz, 2 W
Output voltage: DC 4.2 V, 0.25 A
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions: Approx. 55 × 24 × 83 mm
(2 1/4 × 31/32 × 3 3/8 inches) (W/H/D)
Mass: Approx. 55 g (1.9 oz.)
Rechargeable battery pack
NP-BN1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 0.9 A
Capacity: 
typical: 2.3 Wh (630 mAh)
minimum: 2.2 Wh (600 mAh)
Design and specifications are subject to change 
without notice. 
DSC-W330_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS 
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE 
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS 
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS 
PUBLISHED BY SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 
0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE 
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY 
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU 
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree 
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with 
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•   Unleaded solder melts at a temperature about 40°C higher than 
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to 
about 350°C.
Caution:  The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!
•   Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than 
ordinary solder so use caution not to let solder bridges occur such 
as on IC pins, etc.
•   Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes 
and bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to 
the customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs 
of deterioration. Point them out to the customer and recommend 
their replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Keep the temperature of the soldering iron around 270°C 
during repairing.
 
•   Do not touch the soldering iron on the same conductor of the 
circuit board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering 
or unsoldering.
DSC-W330_L2
1-1
1. SERVICE  NOTE
1-1.  PRECAUTION ON REPLACING THE SY-243 BOARD
RESTORE DATA
When you replace to the repairing board, get the acquire data from the former needed for the adjustment.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• USB Serial No.
• AWB standard data input & check,Color reproduction check
Regarding the PMB Portable
PMB Portable has been written in internal memory.
SY-243 board for service is supplied with written the PMB Portable.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “Destination data write”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB serial No. input”.
1-2.  METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1:  When replacing the SY-243 board, erase the data in internal memory of the board before replacement.
Note 2:   When replacing the SY-243 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a memory card.
1 Insert a memory card with sufficient free capacity into the camera.
2 MENU
t  
(Settings) 
 (Memory Card Tool) 
t [Copy] t [OK] 
t z on the control button
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little 
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• Images cannot be copied individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the 
internal memory, remove the memory card after copying, then format the internal memory ([Format] in 
[Internal Memory Tool]).
• A new folder is created on the memory card and all the data will be copied to it. You cannot choose a 
specific folder and copy images to it.
Notes
– ENGLISH –
Method for Formatting the Internal Memory or Memory Card
Format
Formats the memory card or the internal memory. When you use a memory card with this 
camera for the first time, it is recommended to format the card using the camera for stable 
performance of the memory card before shooting. Note that formatting permanently erases all 
data on the memory card, and is unrecoverable. Save precious data on a computer, etc.
1 MENU
t  
(Settings) 
 (Memory Card Tool) or 
 (Internal 
Memory Tool) 
t [Format] t [OK] t z on the control button
• Note that formatting permanently erases all data including even protected images.
Note
1-3.  HOW TO WRITE DATA TO INTERNAL MEMORY
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust 
Station.
Data writing method
1)   Start the Adjust Manual from the Adjust Station.
2)   Click 
(Write Enable Tool) button.
3)   Click “Activate Write Enable Mode” button.
4)   Upon completion of the setting change, the following message will be displayed.
5)   Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
6)   Write the data read out into the PC to the internal memory of the camera.
7)   Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
Page of 29

Download Sony DSC-W330 (serv.man2) Service Manual (Repair Manual)

Here you can view online or download Sony DSC-W330 (serv.man2) Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Sony DSC-W330 (serv.man2) Digital Camera. Information contained in Sony DSC-W330 (serv.man2) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).