DOWNLOAD Sony DSC-W330 (serv.man2) Service Manual ↓ Size: 5.84 MB | Pages: 29 in PDF or view online for FREE

DSC-W330_L2

1-2

0 0

3 2

C

Repaired by:

Refer to “1-5-3. Self-diagnosis Code Tabl e”.

Indicates the appropriate
step to be taken.
E.g.
13 ....Format the memory card.
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer
E : Corrected by service

engineer

LCD screen

Use the battery (NP-BN1) on repairing.
The external battery source cannot be used on repairing.

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

C

1

3

0

1

The internal memory has experienced a 
media error.

Turn the power off and on again.

The internal memory has experienced a 
format error.

Format the internal memory.

Memory card is unformatted.

Format the memory card.

Memory card is broken.

Replace a new memory card.

Memory card type error

Insert a supported memory card.

The camera cannot read or write data on 
the Memory card.

Turn the power off and on again, or taking out and inserting 
the memory card several times.

C

3

2

0

1

Trouble with hardware

Turn the power off and on again.

E

6

1

0

0

Difficult to adjust focus
(Cannot initialize focus)

Retry turn the power on by the power switch. If it does not 
recover, check the focus reset sensor of lens block 
(pin qh of CN401 on the SY-243 board). If it is OK, check the 
focus motor drive IC (

IC401

 on the SY-243 board).

E

9

1

0

1

Abnormality when flash is being 
charged.

Checking of flash unit or replacement of flash unit. (Note)

Note: After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.

When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash 
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.

Initializes the setting to the default setting. 
Even if you execute this function, the images are retained.

1 MENU

t  

(Settings) 

t   (Main Settings) t [Initialize] t [OK] t

z on the control button

• Be sure not to turn off the camera while initializing.

When problems occur while the unit is operating, the self-diagnosis 
function starts working, and displays on the LCD screen what to 
do.
Details of the self-diagnosis functions are provided in the Instruc-
tion manual.

When problems occur while the unit is operating, the LCD screen 
shows a 4-digit display consisting of an alphabet and numbers, 
whichblinks at 3.2 Hz. This 5-character display indicates the “re-
paired by:”, “block” in which the problem occurred, and “detailed 
code” of the problem.

The changed portions from
Ver. 1.0 are shown in blue.

DSC-W330_L2

1-3

3

Peel off release papers of Barrier Tapes.

4

Install Ornamental Ring A and press it lightly.

Installation
1

Affix two Barrier Tapes to Barrier Assy.
Note: The tape must not be wrinkled.

2

With four claws fitted in position, install the Barrier Assy.

5

Remove Barrier Assy by disengaging four claws.

Ornamental Ring A

Barrier Assy

Barrier Tapes

Barrier Tape

Barrier Tape

A

Removal
1

Turn on the power switch and extend the lens.

2

Detach the battery.

3

Pour a solvent such as alcohol from two places A to the tweezers or a needle shown below into a gap of Ornamental Ring A.

4

Remove while turning the Ornamental Ring A right and left.

Solvent

Ornamental Ring A

Tweezers

Barrier Assy

Claws

Claws

Barrier Assy

Claws

Claws

Barrier
Lever

Hole

Removal
1

Remove four screws, and remove the Rear Mirror Plate.

2

Remove one screw.

3

Remove the four soldering, and remove the Optical Steping Motor (F1380).

1

Solder the four locations.

2

Install the Optical Steping Motor (F1380) with one screw.

3

Install the Rear Mirror Plate with the four screws in the order of nambers.

* Tightening torque = 0.049

± 0.01N • m (0.5 ± 0.1kgf • cm)

* Tightening torque = 0.049

± 0.01N • m (0.5 ± 0.1kgf • cm)

Optical Steping
Motor (F1380)

Optical Steping
Motor (F1380)

Screw

Solders

Screw

Solders

4

1

2

3

Screw

Screw

Screw

Screw

Rear Mirror Plate

Screw

Screw

Screw

Screw

Rear Mirror Plate

DSC-W330_L2

1-4

Removal
1

Remove four screws, and remove the Rear Mirror Plate.

3

Peel off the FG Seal.

2

Remove the Naruto Gear Lubricated Assy and Warm B Lubricated Assy.

4

Remove two screws.

5

Remove the two soldering, and remove the DC Motor Worm A Assy.

2

Install the Naruto Gear Lubricated Assy and Warm B Lubricated Assy.

1

Solder the two locations.

2

Install the DC Motor Worm A Assy with two screws.

2

Put the FG Seal.

3

Install the Rear Mirror Pl ate with the four screws in the order o f nambers.

* Tightening torque = 0.049

± 0.01N • m (0.5 ± 0.1kgf • cm)

* Tightening torque = 0.049

± 0.01N • m (0.5 ± 0.1kgf • cm)

Screw

Screw

Screw

Screw

Rear Mirror Plate

Naruto Gear
Lubricated Assy

Warm B
Lubricated Assy

4

1

2

3

Screw

Screw

Screw

FG Seal

Screw

Screw

Screw

Rear Mirror Plate

Naruto Gear
Lubricated Assy

Warm B
Lubricated Assy

Solders

DC Motor Worm A Assy

Screw

Screw

FG Seal

Solders

DC Motor Worm A Assy

5

Remove the Naruto Gear Lubricated Assy.

Removal
1

Remove four screws, and remove the Rear Mirror Plate.

2

Remove the 3 Group Frame.

3

Remove the 3 Group Spring.

4

Disconnect the Iris Flexible Board from connector of 2 Frame Assy.

Screw

Screw

Screw

Screw

Rear Mirror Plate

Iris Flexible Board

Flexible Board
of 2 Frame Assy

3 Group Frame

3 Group
Spring

3 Group Frame

3 Group Spring

Warm B
Lubricated Assy

The changed portions from
Ver. 1.3 are shown in blue.

DSC-W330_L2

1-5

6

Rotate the Naruto Gear and the lens is drawn out.

8

Rotate the Naruto Gear and the lens is

retractile

.

7

Pass the Flexible Board through the hole of the Fixed Stationaly Tube.

9

Remove the Naruto Gear.

q;

Remove the Fixed Stationaly Tube Block.

qa

Remove the 2 Group Assy.

Flexible Board

Fixed Stationaly Tube

Naruto Gear

Naruto Gear
Lubricated Assy

Fixed Stationaly Tube Block

2 Group Assy

qs

Remove the 1 Group Assy.

qd

Rotate (about 120 degree) Straight Tube Lubcated Assy and align the two points of ditchies of the Straight Tube Lubricated Assy with
ditchies of the Cam Tube Block Assy, then remove the Straight Tube Lubricated Assy from the Cam Tube BlockAssy.

qf

Pour a solvent such as alcohol from two places.

qg

Remove while turning the Ornamental Ring A right and left.

qh

Remove Barrier Assy by disengaging four claws.

qj

Remove the bond at the three points.

qk

Rotate 1 Group Lens Assy and remove it from the 1 Group Frame.

A

Tweezers

1 Group Assy

Straight Tube
Lubricated Assy

Straight Tube
Lubricated Assy

Cam Tube Block Assy

Ditchies

Eyepiece Side View

120

Barrier Assy

Claws

Claws

1 Group Lens Assy

1 Group Frame

Bond

Ornamental Ring A

Solvent

The changed portions from
Ver. 1.3 are shown in blue.