DOWNLOAD Sony DSC-W300 (serv.man3) Service Manual ↓ Size: 800.98 KB | Pages: 37 in PDF or view online for FREE

6-16

DSC-W300_ADJ

The adjustment items of camera system adjustment are as listed in
Table 6-1-4. The Automatic Adjustment Program divides the ad-
justment items into eight, camera adjustment 1 to 8. Clicking ei-
ther CAMERA Adjustment Start button allows the adjustment item
which corresponds to that button to be executed.
The adjustment conditions of the subject and filter vary depend-
ing on which item is adjusted. The Adjustment Program displays
an instruction for the subject and filter as a message during the
adjustment.

Auto Orientation Adj.

11

61

0E0A to 0E0D

CAMERA Adjustment 2

Flange Back Adj.

Siemens star chart with ND filter
for minipattern box (Note) or
Flange back adjustment jig

11

61

069C to 069F,
06CC,
06D8 to 06DF,
0796 to 079D,
0F1C to 0F1D,
0F20, 0F24,
0F26 to 0F53

CAMERA Adjustment 3

Flange Back Check

Siemens star
(1.0m from front the lens)
(Illuminance: 200 to 400 lux)

-

-

-

F No. Compensation

11

61

095A to 095F

Measure Gain, LV Adj.

11

61

0961 to 0968

Mechanical Shutter Adj.

11

61

0980 to 09AD

AWB 3200K-5800K
Standard Data Input

11

61

0C00 to 0C21,
0C24 to 0C49

AWB 3200K-5800K Check

-

-

-

Color Reproduction Adj. &
Check

11

61

0C50 to 0C57

CCD White Defect
Compensation Check

11

61

0200 to 03FF

CCD Black Defect
Compensation Check

11

61

0000 to 01FF

CAMERA Adjustment 6

Strobe Adj.

Flash adjustment box (50 cm)

11

61

0C72 to 0C79

CAMERA Adjustment 7

Auto Focus Illumination Check

Flash adjustment box (50 cm)

11

61

0F10 to 0F15

CAMERA Adjustment 8

Angular Velocity Sensor
Sensitivity Adj.

Not required

11

61

0E10, 0E11

CAMERA Adjustment 1

Hall Adj.

0E00 to 0E04,
0E08, 0E09

11

61

Not required

Clear chart
(Standard picture frame)

CAMERA Adjustment 5

CAMERA Adjustment 4

Clear chart
(Standard picture frame)

9 colors chart
(Standard picture frame)

Dark Siemens star chart.

6-17

DSC-W300_ADJ

6) If the [OK] button is clicked, “3. Auto Orientation Adj.” and

“4. Release of Data Setting during Camera Adj.” will be ex-
ecuted.

7) Upon successful completion of all items of the CAMERA

Adjustment 1, the following message is displayed. Click the
[OK] button.

[Checking method]
1) [HOME screen] 

t  [Settings]  t  [Shooting Settings] t

[Shooting Settings 2] 

t Select [Auto Orientation] to “ON”.

2) Shoot with the set in respective positions (a) to (c) shown be-

low.

3) Check the pictures in the Playback mode to confirm that the

pictures are rotated correctly.

There is no magnetic substance within around 8 cm of the
camera.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Hall Adj.
3. Auto Orientation Adj.
4. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of CAMERA Adjustment 1.
2) The Automatic Adjustment Program executes the “1. Data Set-

ting during Camera Adj.”.

3) Upon successful completion of “1. Data Setting during Cam-

era Adj.”, the following message and screen are displayed. Set
the camera in accordance with the message.

4) If the [OK] button is clicked, “2. Hall Adj.” will be executed.
5) Upon successful completion of “2. Hall Adj.”, the following

message and screen are displayed. Set the camera in accor-
dance with the message.

(a)

(b)

(c)

6-18

DSC-W300_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back Adj.
3. Release of Data Setting during Camera Adj.

Preparation of Flange Back Adj.
(Using the minipattern box)
1) The minipattern box is installed as shown in the following

figure.

The attachment lenses are not used.

Take care not to hit the mini-pattern box when
extending the lens.

2) Install the minipattern box so that the distance between it and

the front of lens of camera is less than 3 cm.

3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the

specified voltage 

± 0.01 Vdc.

5) Check that the center of Siemens star chart meets the center of

shot image screen with the zoom lens at TELE end and WIDE
end respectively.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the
minipattern box.

When using the flange back adjustment jig, take care of
the following points:
• For the illumination, use a light source such as an in-

candescent lamp or inverter type fluorescent light free
from flickering.

• Do not make an adjustment in the environment where

fluorescent lamp flickering occurs even if the il-
Illuminance can be ensured with the room illumina-
tion only. Use an incandescent lamp or inverter type
fluorescent light at a place free from the influence of
room illumination.

1) Install the flange back adjustment jig so that the distance be-

tween it and the front of lens of camera is less than 3 cm.

Take care not to hit the flange back adjustment jig
when extending the lens.

2) Make the height of flange back adjustment jig and the camera

equal.

3) Check that the center of chart meets the center of shot image

screen with the zoom lens at TELE end and WIDE end respec-
tively.

Minipattern box

Below 3 cm

Camera

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±

 0.01 Vdc

Output current : more than 3.5 A

Flange back adjustment jig

Below 3 cm

Camera

6-19

DSC-W300_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back Check
3. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 3.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.

4) Click the [OK] button is clicked, “2. Flange Back Check” is

executed. The following messages are displayed, and then op-
erate the camera to make a check in accordance with the mes-
sages.

5) Upon completion of “2. Flange Back Check”, “3. Release of

Data Setting during Camera Adj.” is executed.

6) Upon successful completion of all items of the CAMERA

Adjustment 3, the following message is displayed. Click the
[OK] button.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation of Flange Back Adj.”.

4) If the [OK] button is clicked, “2. Flange Back Adj.” and “3.

Release of Data Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 2, the following message is displayed. Click the
[OK] button.