Sony DSC-T2 (serv.man4) Service Manual ▷ View online
6-8
DSC-T2_ADJ
4.
Setting of Adjustment Mode
Before performing the adjustment, “Setting of Adjustment Mode”
is required.
is required.
[Setting method]
1) Connect the Camera to the PC with a USB cable, and turn on
1) Connect the Camera to the PC with a USB cable, and turn on
the power switch.
2) Start the Automatic Adjustment Program, and click the [Con-
nect] button on the Main Menu screen.
3) When the following message is displayed, turn off and on again
the power switch of the Camera.
Note:
Turning off and on the power switch causes the Cam-
era to be switched to the Adjustment Mode. After the
Camera restarted, click the [OK] button in the message
window.
era to be switched to the Adjustment Mode. After the
Camera restarted, click the [OK] button in the message
window.
4) Upon successful completion of the settings in the Adjustment
Mode, the operation of each button on the Main Menu screen
is enabled.
is enabled.
5.
Release of Adjustment Mode
To finish the adjustment, be sure to perform “Release of Adjust-
ment Mode”.
ment Mode”.
[Releasing method]
1) Click the [END] button on the Main Menu screen.
2) When the following message is displayed, releasing of adjust-
1) Click the [END] button on the Main Menu screen.
2) When the following message is displayed, releasing of adjust-
ment mode has completed. Click the [OK] button in the mes-
sage window to exit the Automatic Adjustment Program.
sage window to exit the Automatic Adjustment Program.
Note:
The Camera switches to the normal mode by turning
off and on the power switch. After the adjustment fin-
ished, turn off and on again the power switch of the
Camera to confirm that the USB mode screen is dis-
played.
off and on the power switch. After the adjustment fin-
ished, turn off and on again the power switch of the
Camera to confirm that the USB mode screen is dis-
played.
6-9
DSC-T2_ADJ
1-3.
DESTINATION DATA WRITE
Note:
The DESTINATION DATA WRITE cannot be set with other
than the Service board.
than the Service board.
1.
Function of Each Button on Destination Data Write
Screen
Screen
Click the [DESTINATION DATA WRITE] button on the Main Menu
screen, and the “DESTNATION DATA WRITE” screen in Fig. 6-
1-10 will appear.
screen, and the “DESTNATION DATA WRITE” screen in Fig. 6-
1-10 will appear.
Fig. 6-1-10
1
[To Menu] button
Return to the main menu.
Return to the main menu.
2
Destination List
Select the written destination.
Select the written destination.
3
[Data Write] button
Write the destination data to the camera.
Write the destination data to the camera.
2.
Destination Data Write
[Writing method]
1) Select the target destination from the pulldown list.
1) Select the target destination from the pulldown list.
2) Click the [Data Write] button.
3) Following message will be appeared after completing data
writing.
Table 6-1-2
Japanese
English
French
German
Spanish
Italian
Portuguese
Simplified
Chinese
Traditional
Chinese
Dutch
Russian
Korean
Persian
Arabic
Thai
Melayu
Swedish
Norwegian
Danish
Finnish
Polish
Czech
Hungarian
Turkish
Greek
J1
J
z
NTSC
JE3
JE
z
a
a
a
a
a
a
a
a
a
PAL
U2
US
z
a
a
a
a
a
NTSC
CA2
CND
z
a
a
a
a
a
NTSC
CEE2
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
PAL
CEE8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEE9
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEH
UK
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E15
z
a
a
a
a
a
a
a
a
a
PAL
E32
z
a
a
a
a
a
a
a
a
a
PAL
E33
a
z
a
a
a
a
a
a
a
a
NTSC
TH6
Thai
a
a
a
a
a
a
a
a
z
a
PAL
AR2
AR
a
z
a
a
a
a
a
a
a
a
NTSC
AU2
AUS
z
a
a
a
a
a
PAL
HK1
HK
z
a
a
a
a
a
a
a
a
a
PAL
CN2
CH
a
a
a
z
a
a
a
a
a
a
PAL
KR2
KR
a
a
a
a
a
z
a
a
a
a
NTSC
BR1
BR
a
a
z
a
a
a
a
a
a
a
NTSC
z
: INITIAL LANGUAGE
E
VIDEO OUT
Default
AEP
DESTINATION
AREA
SELECTABLE LANGUAGE
3
2
1
Ver. 1.3 2008.05
6-10
DSC-T2_ADJ
1.
Function of Each Button on USB Serial No. Input
Screen
Screen
Click the [USB SERIAL No. INPUT] button on the Main Menu
screen, and “USB SERIAL No. INPUT” screen in Fig. 6-1-11
will appear.
screen, and “USB SERIAL No. INPUT” screen in Fig. 6-1-11
will appear.
Fig. 6-1-11
1
[To Menu] button
The Main menu screen comes back.
The Main menu screen comes back.
2
Display area
The “PRODUCT ID” and “SERIAL No.” are displayed.
The “PRODUCT ID” and “SERIAL No.” are displayed.
3
[Check Serial] button
The USB SERIAL No. data is read from the camera and dis-
played in the display area.
The USB SERIAL No. data is read from the camera and dis-
played in the display area.
4
[Read and Save] button
The USB SERIAL No. data is read from the camera and saved
in PC as a file.
Default file name is as follows:
The USB SERIAL No. data is read from the camera and saved
in PC as a file.
Default file name is as follows:
5
[Load and Write] button
The USB SERIAL No. data is loaded from the file saved in
PC and written to the camera.
The USB SERIAL No. data is loaded from the file saved in
PC and written to the camera.
6
Input area
Enter the “SERIAL No.”.
For the “PRODUCT ID”, the last 5 characters of model
name are fixed. For the “SERIAL No.”, read it from the label
on the camera body and enter it.
Enter the “SERIAL No.”.
For the “PRODUCT ID”, the last 5 characters of model
name are fixed. For the “SERIAL No.”, read it from the label
on the camera body and enter it.
7
[Write Manually] button
The USB SERIAL No. data entered in the input area is written
to the camera.
The USB SERIAL No. data entered in the input area is written
to the camera.
1-4.
USB SERIAL No. INPUT
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and there-
fore it must be entered after the board replacement.
If original ID can be read from the board before replacement, read
it from the board before replacement using the “SERIAL READ/
WRITE” screen, and then write it after replacement.
If original ID cannot be read from the board before replacement,
write the ID for service using the “MANUAL WRITE” screen.
(The ID for service is different from the ID written when the set is
shipped.) Enter the PRODUCT ID (last 5 characters of model
name) and SERIAL No. into the screen and write them.
This ID has not been written in a new board for service, and there-
fore it must be entered after the board replacement.
If original ID can be read from the board before replacement, read
it from the board before replacement using the “SERIAL READ/
WRITE” screen, and then write it after replacement.
If original ID cannot be read from the board before replacement,
write the ID for service using the “MANUAL WRITE” screen.
(The ID for service is different from the ID written when the set is
shipped.) Enter the PRODUCT ID (last 5 characters of model
name) and SERIAL No. into the screen and write them.
DSC-T2_SERIAL_xxxxxxxx_yyyymmdd.dat
Date
USB serial number
Data name
USB serial number
Data name
Ver. 1.2 2008.02
5
3
4
2
7
6
1
6-11
DSC-T2_ADJ
1-5.
VIDEO SYSTEM ADJUSTMENTS
1-5-1.
Function of Each Button on Video System
Adjustment Screen
Adjustment Screen
Click the [VIDEO SYSTEM ADJUSTMENT] button on the Main
Menu screen, and the “VIDEO SYSTEM ADJUSTMENT”
screen in Fig. 6-1-12 will appear.
Menu screen, and the “VIDEO SYSTEM ADJUSTMENT”
screen in Fig. 6-1-12 will appear.
Fig. 6-1-12
1
[To Menu] button
Return to the main menu.
Return to the main menu.
2
[Preparation] button
Notes for adjustment or jigs used are displayed.
Notes for adjustment or jigs used are displayed.
3
[Start] button
Each adjustment “Composite Video Level Adjustment” or
“Component Video Level Adjustment” starts.
Each adjustment “Composite Video Level Adjustment” or
“Component Video Level Adjustment” starts.
4
[Reboot] button
When this button is clicked, the camera is rebooted.
When this button is clicked, the camera is rebooted.
5
[Release Data Setting] button
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the video adjust-
ment. If the adjustment completed successfully, the data set-
ting is automatically cancelled and the button color returns to
“white”.)
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the video adjust-
ment. If the adjustment completed successfully, the data set-
ting is automatically cancelled and the button color returns to
“white”.)
1-5-2.
Adjustment Items of VIDEO System Adjust-
ment
ment
The adjustment items of video system adjustment are as listed in
Table 6-1-3. The Automatic Adjustment Program executes the ad-
justment items if the VIDEO Adjustment Start button is clicked.
Table 6-1-3. The Automatic Adjustment Program executes the ad-
justment items if the VIDEO Adjustment Start button is clicked.
Table 6-1-3
5
4
3
2
1
Block
Page
Address
Composite
Video Level
Adjustment
Video Level
Adjustment
Composite Video
Level Adj.
Level Adj.
VIDEO terminal of USB, A/V, DC IN
cable for multi-use terminal
(75 ohm terminated)
cable for multi-use terminal
(75 ohm terminated)
Oscilloscope
11
60
06B8
Component Out
Y Level Adj.
Y Level Adj.
Land of HD_Y
(Component video out jig)
(Component video out jig)
Oscilloscope
11
60
0680
Component Out
Pb Level Adj.
Pb Level Adj.
Land of HD_Pb
(Component video out jig)
(Component video out jig)
Oscilloscope
11
60
0681
Component Out
Pr Level Adj.
Pr Level Adj.
Land of HD_Pr
(Component video out jig)
(Component video out jig)
Oscilloscope
11
60
0682
Adjusting Address
Component
Video Level
Adjustment
Video Level
Adjustment
Button
Name
Adjustment
Measurement Point
Measuring
Instrument
Click on the first or last page to see other DSC-T2 (serv.man4) service manuals if exist.