DOWNLOAD Sony DSC-T2 (serv.man4) Service Manual ↓ Size: 699.76 KB | Pages: 39 in PDF or view online for FREE

6-24

DSC-T2_ADJ

Note down the PITCH/YAW data on the replacement lens for repair.

Adjustment Block

11

Adjustment Page

61

Adjustment Address

0E10, 0E11

The PITCH/YAW data of lens is written only repair parts.

Preparation:
1) Read the PITCH data written on repair parts, and named this

as L

1

.

2) Read the YAW data written on repair parts, and named this as

L

2

.

YAW data    

t

 L

2

PITCH/YAW Data

PITCH data 

t

 L

1

P.PP / Y.YY

P.PP/ Y.YY

[Adjusting method]
1) Click the [Start] button of Camera Adjustment 9, and the fol-

lowing screen will appear.

The buttons on this screen provide the following functions.
[Read] button: Reads and displays the previous data (Dp, Dy)

from the SY-180 board.

[Save] button: Saves the previous data (Dp, Dy) in the PC as a

file.

[Load] button: Loads and displays the previous data (Dp, Dy)

from the file saved in the PC.

• Default file name is as follows:

2) Input the previous data (Dp, Dy) into screen.

If the previous data cannot be read, give a check to the checkbox
at lower left of screen.

3) Input the sensitivity of respective sensors (S

501

, S

502

) read at

“Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.

4) Input the PITCH/YAW data of lens (L

1

, L

2

) read at “Prepara-

tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.

In order to get the correct value for the adjustment, it is
necessary to input a decimal point (“period” or  “comma”)
as same format as windows setting because “Numeric Val-
ue Format” depend on the language. (F:123 456 789,00,
GB:123,456,789.00, D:123.456.789,00)
“Numeric Value Format” setting is available in “Control
Panel”-“Regional and Language Options”.

5) Click the [OK] button, and the adjustment data is then calcu-

lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.

6) Upon successful completion of the data writing, the following

screen will appear. Check that the steady shot function oper-
ates normally.

DSC-T2_D

p

D

y

DT_xxxxxxxx_yyyymmdd.dat

Date
USB serial number
Data name

6-25

DSC-T2_ADJ

The adjustment items of LCD system adjustment are as listed in
Table 6-1-5. The Automatic Adjustment Program executes the ad-
justment items if the LCD Adjustment Start button is clicked.

Button

Adjustment

Adjusting  Address

Name

Block

Page

Address

LCD

V-COM Adj.

11

60

0401

Adjustment White Balance Adj.

11

60

040F, 0411

Touch
Panel

Touch Panel Adj.

(Note)

Adjustment

The adjustment data cannot be read or written the SeusEX.

Click the [LCD SYSTEM ADJUSTMENT] button on the Main Menu
screen, and the “LCD SYSTEM ADJUSTMENT” screen in Fig.
6-1-24 will appear.

1

[To Menu] button
Return to the main menu.

2

[Start] button
Each adjustment “LCD Adjustment” or “Touch Panel Adjust-
ment” starts.

3

[Reboot] button
When this button is clicked, the camera is rebooted.

3

2

1

6-26

DSC-T2_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during LCD Adj.
2. V-COM Adj.
3. White Balance Adj.

[Adjusting method]
1) Click the [Start] button of the LCD Adjustment.
2) The Automatic Adjustment Program executes “1. Data Setting

during LCD Adj.”.

3) Upon successful completion of the “1. Data Setting during LCD

Adj.”, the following screen is displayed during the execution
of “2. V-COM Adj.”. Using the [Up]/[Down]  button on the
screen, adjust so that the brightness of portions A and B on the
LCD panel is equal. After the adjustment, click the [End] but-
ton in the screen.

4) If the [End] button is clicked, the following screen is displayed

during the execution of “3. White Balance Adj.”. Check that
the LCD screen is not colored. If colored, using the [Up]/[Down]
button on the screen, adjust so that the LCD screen is not col-
ored. After the adjustment, click the [End] button in the screen.

5) Upon successful completion of all item the LCD Adjustment,

the following message is displayed. Click the [OK] button.

6-27

DSC-T2_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Touch Panel Adj.

[Adjusting method]
1) Click the [Start] button of the Touch Panel Adjustment.
2) The Automatic Adjustment Program executes the “1. Touch

Panel Adj.”. The following message is displayed, and then
adjust the LCD screen in accordance with the instructions given
on the screen.

3) Upon successful completion of all item the Touch Panel Ad-

justment, the following message is displayed. Click the [OK]
button.