DOWNLOAD Sony DSC-S60 / DSC-S80 / DSC-S90 / DSC-ST80 (serv.man2) Service Manual ↓ Size: 6.24 MB | Pages: 57 in PDF or view online for FREE

DSC-S60/S80/S90/ST80

2-1

2-2

The following flow chart shows the disassembly procedure.

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between the two 
points with the short jig about 10 
seconds.

14

2

5

6

1

Open the BT lid.

2

Screw (M1.7) 

x1

3

Screw (M1.7) 

x3

4

Close the BT lid.

5

Claw 

x1

6

Claw 

x1

7

Claw 

x3

8

Cabinet (rear) block

9

Claw 

x1

0

Claw 

x2

qa

Cabinet (front) block

1

Claw 

x4

2

Control switch block

1

Flexible board: CN702

2

Slide the cabinet (upper) to 
upper side and remove claw.

3

Claw 

x1

4

Claw 

x1

5

Cabinet (upper) block

6

Mic harness: CN703

1

Claw 

x1

2

Claw 

x1

3

Lift the ST holder.

4

Flexible board of D002 section

5

Claw 

x2

6

Flexible board of flash unit section

1

Screw (M1.7) 

x1

2

Flexible board of BT001 section

3

Flexible board of SP901 section

4

Claw 

x2

5

Claw 

x2

6

Flexible board: CN701

7

MC-153

2

1

3

5

6

4

2

3

1

1

4

2

5

5

3

5

6

4

9

0

7

7

3

3

3

8

qa

1

Turn lens ring to the position 
which the line of lens ring and 
the line of front cabinet suit.

2

Lens ring

Line

Line

1

2

7

6

1

1

2

Note: Mic harness is connected.

Note: Speaker adhesive sheet

cannot be recycle.

Speaker adhesive sheet

R:1 k

Ω

/1 W

 

(Part code: 
1-215-869-11)

DSC-S60/S80/S90/ST80

2-3

2-4

1

Claw 

x1

2

Capacitor (C003)

3

Claw 

x2

4

ST-122

5

Tapping screw 

x1

6

Claw 

x2

7

MS-271

1

Flexible board: CN704

2

BT harness: CN001

3

Flexible board: CN705

4

Claw 

x3

5

Battery holder block

1

Claw 

x3

2

Flexible board: CN401

3

Flexible board: CN601

4

Lens block

5

Claw 

x1

6

Claw 

x2

7

Flexible board: CN706

8

SY-126

1

Flexible board: CN003

2

Flexible board: CN004

3

Claw 

x1 (S60/S80/ST80)

Claw 

x2 (S90)

4

Claw 

x1

5

D901

6

Claw 

x4

7

LCD901

8

Push the claw.

9

Remove the SW-446 in the
direction of arrow 

A

.

A

S90

S60/S80/ST80

5

1

2

3

1

2

1

1

1 2

3

1

2

8

5

7

3

3

6

6

4

4

4

4

8

4

7

3

3

6

5

5

6

6

7

4

DSC-S60/S80/S90/ST80

14

2

5

6

9

0

7

7

3

3

3

8

qa

2

1

3

5

6

4

2

3

1

1

4

2

5

5

3

5

6

4

7

6

5

1

2

3

4

4

4

A

S90

S60/S80/ST80

1

2

1

1

1 2

3

1

2

8

5

7

3

3

6

6

4

8

4

7

3

3

6

5

5

6

6

7

4

Connection cord (DK-2AA)
(1-830-351-11)

Lens block

MC-153 flexible

SY-126 board

SW-446 board

D901, LCD901
(Note)

Cabinet (upper) block
(Control switch block)

MS-271 board

AC power
adaptor

AC IN

ST-122 flexible

BT901

Color monitor

A/V multi cable
(Note)

2-5

2-6

If the A/V multi cable is connected to the multi connector

of MC-153 flexible board, the image can not appear on the
LCD screen.

If you want to confirm the circuit of LCD drive or LCD,

disconnect the A/V multi cable.

DSC-S60/S80/S90/ST80

2-7

2-8E

After the barrier unit is replaced, check the following items with turning the power of the set ON/OFF.
• The lens moves out and the barrier shutters open completely when the power is turned on.
• The lens moves in and the barrier shutters close completely when the power is turned off.
Checking condition is 

1

 downward 

2

 45

°

 downward 

3

 horizontal 

4

 45

°

 upward 

5

 upward; totally five positions

and check three times for each position.

The test needs to be performed only when the barrier unit is replaced.
No performance of this test is needed when the lens is replaced.

1

 downward

2

 45

°

 downward

3

 horizontal

4

 45

°

 upward

5

 upward

1

Switch on a power supply.

3

Switch off a power supply by taking out a battery
or cut off a power supply from AC daptor.
 (without using camera's power swich)

4

Pinch 

A

 portion with finger

and fit a driver over a hollow.

A

2

Push zoom button and transform the lens
as shown below.

5

Ornamental fixed plate (A)

7

Barrier unit

6

Two screws
(M1.4 

×

 4.5)

CD-573

CCD IMAGER

CH-169

CCD SIGNAL PROCESS

(included in SY-126)
MC-153 flexible

MULTI CONNECTOR

MS-271

MEMORY STICK CONNECTOR

ST-122 flexible

FLASH DRIVE

SW-446

CONTROL SWITCH, LCD PANEL

SY-126

CAMERA MODULE, CAMERA DSP, CPU, 

(including CP401 

LENS DRIVE, BURST FLASH, SDRAM, AND FLASH

,

 

(

CH-169 board))

AUDIO, DC/DC CONVERTER, CONNECTOR

CD-573

SY-126
(including CP401 (

CH-169 board))

SW-446

ST-122 flexible

MS-271

MC-153 flexible

CH-169
(included in SY-126)