DOWNLOAD Sony DSC-S60 / DSC-S80 / DSC-S90 / DSC-ST80 (serv.man2) Service Manual ↓ Size: 6.24 MB | Pages: 57 in PDF or view online for FREE

1-1

DSC-S60/S80/S90/ST80

The charging capacitor (C003) of ST-122 flexible board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand.  The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off.  Therefore, the remaining
voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.

1 k

Ω

/1 W

Wrap insulating tape.

Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.

Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.

When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.

R:1 k

Ω

/1 W

 

(Part code: 
1-215-869-11)

1-2

DSC-S60/S80/S90/ST80

When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.

• C: ss: ss

You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)

• E: ss: ss

Contact your Sony dealer or local
authorized Sony service facility.

Display Code

  C:32:ss

  C:13:ss

Countermeasure

Turn the power off and on again.

Format the “Memory Stick” or internal
memory.

Cause

Trouble with hardware.

“Memory Stick” or internal memory is
unformatted.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR

  E:61:ss

  E:91:ss

  E:92:ss

Insert a new “Memory Stick”.

“Memory Stick” is broken.

Turn the power off and on again.

Trouble with internal memory.

INTERNAL MEMORY ERROR

Checking of lens drive circuit.

When failed in the focus and zoom
initialization.

—

Checking of flash unit or replacement
of flash unit. (Note)

Insert batteries correctly.

Abnormality when flash is being
charged.

Batteries are not inserted correctly.

After repair, be sure to perfom “1-6. PROCESS AFTER FIXING FLASH ERROR”.

Tapping screw

Lens block assembly

Lens flame 

1-3

DSC-S60/S80/S90/ST80

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)

When replacing the SY-126 board, erase the data in internal memory of the board before replacement.

When replacing the SY-126 board or the IC301 on the SY-126 board, execute formatting and initialize the internal memory after
replacement.

Formats the internal memory.

• Note that formatting irrevocably erases all data in the internal memory, including even protected images.

1

Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.

2

Select [OK] with v, then press z.
The format is complete.

OK

See the following procedure.

Cancel

Cancels the formatting.

Copies all images in the internal memory to a “Memory Stick”.

1

Insert a “Memory Stick” having 32 MB or larger capacity.

2

Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.

3

Select [OK] with v, then press z.
Copying starts. 

• Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files 

using batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly 
corrupting the data.

• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the 

internal memory, remove the “Memory Stick” after copying, then execute the [Format] command in 

 

Internal Memory Tool.

• You cannot select a folder copied on a “Memory Stick”.

• The setting of 

 (Print order) marks is not copied even when you copy data.

OK

See the following procedure.

Cancel

Cancels the copying.

1-4E

DSC-S60/S80/S90/ST80

When “FLASH error”  (Self-diagnosis Code  E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.

Initializes the setting to the default setting.

1

Select [OK] with v on the control button, then press z.
The message “Initialize all settings Ready?” appears.

2

Select [OK] with v, then press z.
The settings are reset to the default setting.

• Make sure that the power is not disconnected during resetting.

OK

See the following procedure.

Cancel

Cancels the resetting.