DOWNLOAD Sony DSC-S30 / DSC-S50 (serv.man2) Service Manual ↓ Size: 6.6 MB | Pages: 96 in PDF or view online for FREE

Adjust the color separation matrix coefficient so that proper color
reproduction is produced.

Mode

STILL

Subject

Color bar chart
(Color reproduction adjustment frame)

Adjustment Page

F

Adjustment Address

41 to 48, 5C to 5F

Perform “Auto White Balance Standard Data Input”
before this adjustment.

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, and set data: FF.

3)

Select page: D, address: 63, set data: 40, and press the PAUSE
button of the adjusting remote commander.

4)

Perform “ Data setting during camera system adjustment”.
(Refer to page 5-13)

5)

Select page: 6, address: 01, set data: AB, and press the PAUSE
button.

6)

Select page: 6, address: 12, set data: 80, and press the PAUSE
button.

7)

Wait for 1 second.

8)

Select page: 6, address: 12, set data: 00, and press the PAUSE
button.

9)

Wait for 2 seconds.

10) Select page: 6, address: 01, set data: A9, and press the PAUSE

button. (The color reproduction adjustment is performed and
the adjustment data is stored in page: F, address: 41 to 48,
5C to 5F)

11) Select page: 6, address: 02, and check that the data is “01”.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.

2)

Select page: 5, address: F1, and set data: 00.

3)

Select page: D, address: 63, set data: 00, and press the PAUSE
button.

4)

Release the data setting performed at step 4).
(Refer to page 5-13)

5)

Select page: 0, address: 01, and set data: 00.

6)

Perform “Color Reproduction Check”.

M

G

Y

E

C

Y

R-Y

B-Y

R

B

G

Burst position

M

G

Y

E

C

Y

R-Y

B-Y

R

B

G

Burst position

Mode

STILL

Subject

Color bar chart
(Color reproduction adjustment frame)

Measurement Point

Video terminal of A/V OUT jack
(75 

Ω

 terminated)

Measuring Instrument Vectorscope

Specified Value

All color luminance points shouldsettle
within each color reproduction frame.

Menu setting:
1)

VIDEO OUT of SET UP menu

................................

NTSC (NTSC mode)

................................

PAL (PAL mode)

Checking method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, and set data: FF.

3)

Select page: D, address: 63, set data: 40, and press the PAUSE
button of the adjusting remote commander.

4)

Perform “ Data setting during camera system adjustment”.
(Refer to page 5-13)

5)

Check that the picture frame is set to the specified position.
(Refer to “6. picture Frame Setting” )

6)

Select page: 6, address: 10, and set data: 01.

7)

Select page: E, address: 52, after noting down the data, set
data: 0A, and press the PAUSE button.

8)

Select page: 6, address: 01, set data: 0F, and press the PAUSE
button.

9)

Select page: 6, address: 12, set data: 80, and press the PAUSE
button.

10) Wait for 1 second.
11) Select page: 6, address: 12, set data: 00, and press the PAUSE

button.

12) Wait for 2 seconds.
13) Check the each color luminance point in each color repro-

duction frame.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.

2)

Select page: 6, address: 10, and set data: 00.

3)

Select page: E, address: 52, set data noted down at step 7)
and press the PAUSE button.

4)

Select page: 5, address: F1, and set data: 00.

5)

Select page: D, address: 63, set data: 00, and press the PAUSE
button.

6)

Release the data setting performed at step 4).
(Refer to page 5-13)

7)

Select page: 0, address: 01, and set data: 00.

R-Y

B-Y

4mm

4mm

R-Y

B-Y

2.5mm

1mm

6mm

6mm

Mode

STILL

Subject

Clear chart
(Color reproduction adjustment frame)

Measurement Point

Displayed data of

Video terminal of

Page: 1 (Note 2)

A/V OUT jack
(75 

Ω

 terminated)

Measuring Instrument Adjustment remote

Vectorscope

Commander

Specified Value

R ratio: 3E00 to 4200 Fig. 5-1-18
B ratio: 3E00 to 4200 (A) and (B)

Refer to “6. Picture Frame Setting” for XH, XL, YH and
YL.

The right four digits of the page: 1 displayed data of the
adjusting remote commander.

                    1:XX:XX



Displayed data

Checking method:
1)

Check that the lens is not covered with either filter.

2)

Select page: 0, address: 01, and set data: 01.

3)

Select page: 5, address: F1, and set data: FF.

4)

Select page: D, address: 63, set data: 40, and press the PAUSE
button of the adjusting remote commander.

5)

Perform “ Data setting during camera system adjustment”.
(Refer to page 5-13)

6)

Select page: 6, address: 90, and set data: XL. (Note 1)

7)

Select page: 6, address: 91, and set data: XH. (Note 1)

8)

Select page: 6, address: 92, and set data: YL. (Note 1)

9)

Select page: 6, address: 93, and set data: YH. (Note 1)

10) Select page: 6, address: 6C, and set data: 01.
11) Select page: 6, address: 01, set data: 79, press the PAUSE

button, and wait for 1 second.

12) Select page: 6, address: 2C, and set data: 01.
•

INDOOR data check

13) Select page: E, address: 52, after noting down the data, set

data: 0E, and press the PAUSE button.

14) Select page: 6, address: 01, set data: 0F, and press the PAUSE

button.

15) Select page: 0, address: 03, and set data: 04.
16) Select page: 1, and check that the displayed data (Note 2)

satisfies the R ratio specified value.

17) Select page: 0, address: 03, and set data: 05.
18) Select page: 1, and check that the displayed data (Note 2)

satisfies the B ratio specified value.

•

INDOOR luminance point check

19) Select page: 6, address: 1C, and set data: 00.
20) Select page: 0, address: 03, and set data: 00.
21) Check that the center of the white luminance point is within

the circle shown Fig. 5-1-18 (A).

•

OUTDOOR luminance point check

22) Place the C14 filter on the lens.
23) Select page: E, address: 4B, after noting down the data, set

data: 20, and press the PAUSE button.

24) Select page: 6, address: 01, set data: 3F, and press the PAUSE

button.

25) Check that the center of the white luminance point settles in

the circle shown Fig. 5-1-18 (B).

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.

2)

Select page: 6, adderss: 6C, and set data: 00.

3)

Select page: E, address: 52, set data noted down at step 13)
and press the PAUSE button.

4)

Select page: E, address: 4B, set data noted down at step 23)
and press the PAUSE button.

5)

Select page: 5, address: F1, and set data: 00.

6)

Select page: D, address: 63, set data: 00, and press the PAUSE
button.

7)

Release the data setting performed at step 5).
(Refer to page 5-13)

8)

Select page: 0, address: 01, and set data: 00.

R-Y

B-Y

4mm

8mm

8mm

Check the light level regulation and the white balance when the
strobe light flashed.

Mode

STILL

Subject

Flash adjustment box (Note 3)

(1.0 m from the front of lens)

Measurement Point

Displayed data of page: 1

Measuring Instrument Adjusting remote commander

Specified value

Y level data: 60 to 94
R-Y level data: FA to FF or 00 to 06
(Note 4)
B-Y level data: FA to FF or 00 to 06
(Note 4)

Perform this checking successively after performing
“HALL Adjustment”,  “Flange Back Adjustment”, “ Light
Level Adjustment”, “Strobe White Balance Adjustment”
and “Auto White Balance Standerd Data Input”. (Do not
turn the power of unit OFF)

Perform this adjustment in the Flash adjustment box.

Refer to “4. Preparing the Fiash adjustment box”.
(See page 5-7)

The right four digits of the page: 1 displayed data of the

adjusting remote commander.
 1:XX:XX

 

B-Y level data

 

R-Y level data

Displayed data of page: F, address: 64 of the adjusting
remote commander.

 F:XX:64

 

Y level data

Check that the data of page: 6, address: 02 is “00”.

Checking method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 6, address: 01, set data: 79, and press the PAUSE
button of the adjusting remote commander.

3)

Select page: 6, address: 01, set data: 67, and press the PAUSE
button.

4)

Check the flashing of strobe light.

5)

Select page: F, address: 64, and check that the data satisfies
the Y level data specified value. (Note 5)

6)

Select page: 0, address: 03, and set data: 02.

7)

Select page: 1, and check the R-Y, B-Y level data (Note 4)
satisfies the specified value.

Processing after Completing Adjustments:
1)

Select page: 0, address: 03, and set data: 00.

2)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.

3)

Select page: 6, address: 2C, and set data: 00.

4)

Select page: 6, address: 6C, and set data: 00.

5)

Select page: 6, address: 93, and set data: 00.

6)

Select page: 7, address: 03, set data: 00, and press the PAUSE
button.

7)

Select page: 5, address: F1, and set data: 00.

8)

Select page: D, address: 63, set data: 00, and press the PAUSE
button.

9)

Release thedata setting performed at step 4) of “Strobe White
Balance Adjustment”. (Refer to page 5-13)

10) Select page: 0, address: 01, and set data: 00.

Adjust the white balance when the strobe light flashed.

Mode

STILL

Subject

Flash adjustment box (Note 3)

(1.0 m from the front of lens)

Adjustment Page

F

Adjustment Address

4D, 4E, 64, 69, 6A, 6B

Perform  “HALL Adjustment”,  “Flange Back Adjust-
ment”, “Light Level Adjustment”, “Auto White Balance
Adjustment” and “Auto White Balance Standerd Data In-
put” before this adjustment.

Perform this adjustment in the Flash adjustment box.

Refer to “4. Preparing the Flash adjustment box”.
(See page 5-7)

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Switch setting:
1)

FLASH ......................

ON

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, and set data: FF.

3)

Select page: D, address: 63, set data: 40, and press the PAUSE
button of the adjusting remote commander.

4)

Perform “ Data setting during camera system adjustment”.
(Refer to page 5-13)

5)

Select page: 7, address: 03, and set data: 08.

6)

Select page: 6, address: 90, and set data: 00.

7)

Select page: 6, address: 91, and set data: 00.

8)

Select page: 6, address: 92, and set data: 00.

9)

Select page: 6, address: 93, and set data: 80.

10) Select page: 6, address: 6C, and set data: 01.
11) Select page: 6, address: 2C, and set data: 01.
12) Select page: 6, address: 01, set data: 79, and press the PAUSE

button.

13) Select page: 6, address: 01, set data: 67, and press the PAUSE

button.

14) Select page: 6, address: 01, set data: 00, and press the PAUSE

button.

15) Select page: 6, address: 01, set data: 79, and press the PAUSE

button.

16) Select page: 6, address: 01, set data: 67, and press the PAUSE

button.

17) Select page: 6, address: 01, set data: 00, and press the PAUSE

button.

18) Select page: 6, address: 01, set data: 79, and press the PAUSE

button.

19) Select page: 6, address: 01, set data: B9, and press the PAUSE

button. (The strobe white balance adjustment is performed
and the adjustment data is stored in page: F, address: 4D, 4E,
64, 69, 6A and 6B)

20) Select page: 6, address: 02, and check that the data is “01”.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjusting remote commander.

2)

Perform “Strobe Light Level and White Balance Check” suc-
cessively. (Do not turn the power of unit OFF)