DOWNLOAD Sony DSC-RX100 (serv.man2) Service Manual ↓ Size: 6.19 MB | Pages: 27 in PDF or view online for FREE

Model
DSC-RX100 (serv.man2)
Pages
27
Size
6.19 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL2
File
dsc-rx100-sm2.pdf
Date
PREV: Sony DSC-RX100 Service Manual

Sony DSC-RX100 (serv.man2) Service Manual ▷ View online

DSC-RX100_L2
2-4
2-1-2. OVERALL SECTION-2
Ref. No. 
Part No. 
Description
Ref. No. 
Part No. 
Description
  51 
A-1887-589-A  MS-504 BOARD, COMPLETE
  52 
1-886-328-11 
MS-505 FLEXIBLE BOARD
  53 
4-433-868-01 
HOLDER (500), SY
  54 
4-433-869-01 
PLATE (500), HDMI FIXED
  55 
A-1887-618-A  SY-335 BOARD, COMPLETE (SERVICE)
  56 
4-433-876-01 
PLATE (500), USB FIXED
  57 
4-433-872-01 
CUSHION (LENS) (UPPER) (500)
  58 
4-433-874-01 
SHEET (CD) (500), RADIATION (Note 2)
  59 
4-433-873-01 
CUSHION (LENS) (LOWER) (500)
  60 
A-1896-681-A  CD-847 FLEXIBLE BOARD, COMPLETE (SERVICE) 
(including CP001 (CMOS imager)) (Note 4, 5, 6)
 61 
Selection 
Parts
  62 
4-435-725-01 
SHEET (500), FLEXIBLE FIXED
  63 
A-1887-590-A  SE-184 FLEXIBLE BOARD, COMPLETE
  64 
4-433-867-01 
SHEET (500), SE FLEXIBLE FIXED
  65 
4-417-286-01 
LIGHT SHIELD RING
 SP901  1-858-785-11  LOUDSPEAKER 
(0.8CM)
  #177 
3-208-537-21 
0+Z M1.4X2 NEW TORASUTA
 #274  4-431-868-01  SCREW, 
0+P2M1.4X3.5SG
1.  Remove in numerical order (
1
 
to
 
2
) in the left figure.
2.  The meaning of the symbol in left figure is as follows. Be careful when you remove it.
 
◇-X
:  Solder
DISASSEMBLY
Note
Note 1 :
  Hold the Lens Block at the
    center of both sides.
  Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Lens Barrier
  Very weak
Zoom Motor
  Very weak
Focus Lens
  Very weak
Screw
3-208-537-21
(Red)
M1.4 X 2.5
#177:
2.5
1.4
#274: M1.4 X 3.5
(Silver)
4-431-868-01
3.5
1.4
1
  #177 X 2
#177
#177
Back View
Note 2:  Do not reuse the Radiation Sheet (CD) (500) because its ad-
hesive force decreases when it is removed once.
Note 3:  Refer to “Assembly-6: Precaution During Lens Block Installa-
tion”.
Note 2:  Radiation Sheet (CD) (500) は一度剥がすと粘着力が弱くなるた
め、再利用はしないでください。
Note 3:  Assembly-6: Precaution During Lens Block Installation  を参照
してください。
MS-504
SY
-335
 (Claws)
 (Claws)
#177
#177
SP901
#274
51
52
53
54
56
57
 58
(Note 2)
59
60
62
63
64
65
1
55
2
BTH ASSY and ST Section
(See page 2-5)
‘
Lens Block Section
(See page 2-8)
 61
 61
(Note 1, 3, 4)
(including CD-847 flexible 
 complete board,CP001 
(CMOS imager))
(Note 4, 5, 6)
Note 4:  When this part is removed, adjustment is required.
 
For the adjustment method, refer to “Adjustment items after 
replacing parts” in the Note tab of the Adjust manual.
Note 4:  この部品を取り外したときは調整が必要です。
 
調整方法については Adjust manual の Noteタブにある Adjustment 
items after replacing parts を参照してください。
Note 5:  Refer to “1-3.  NOTES ON REMOVING/INSTALLING THE 
IMAGER BOARD (CD-847 FLEXIBLE BOARD)”.
Note 5:  1-3. イメージャ基板 (CD-847フレキシブル基板) の取り外し／取
り付け時の注意  を参照してください。
SELECTION PARTS
Ref. No.61
These parts are provided for shift and tilt adjustment.
Change the thickness (t) according to result of adjustment.
4-410-539-01 
SPACER PLATE (A) (t=0.10)
4-410-539-11 
SPACER PLATE (A) (t=0.11)
4-410-539-21 
SPACER PLATE (A) (t=0.12)
4-410-539-31 
SPACER PLATE (A) (t=0.13)
4-410-539-41 
SPACER PLATE (A) (t=0.14)
4-410-539-51 
SPACER PLATE (A) (t=0.15)
4-410-539-61 
SPACER PLATE (A) (t=0.16)
4-410-539-71 
SPACER PLATE (A) (t=0.17)
4-410-539-81 
SPACER PLATE (A) (t=0.18)
4-410-539-91 
SPACER PLATE (A) (t=0.19)
4-410-540-01 
SPACER PLATE (B) (t=0.20)
4-410-540-11 
SPACER PLATE (B) (t=0.21)
4-410-540-21 
SPACER PLATE (B) (t=0.22)
4-410-540-31 
SPACER PLATE (B) (t=0.23)
4-410-540-41 
SPACER PLATE (B) (t=0.24)
4-410-540-51 
SPACER PLATE (B) (t=0.25)
4-410-540-61 
SPACER PLATE (B) (t=0.26)
4-410-540-71 
SPACER PLATE (B) (t=0.27)
4-410-540-81 
SPACER PLATE (B) (t=0.28)
4-410-540-91 
SPACER PLATE (B) (t=0.29)
4-437-388-01 
SPACER PLATE C (t=0.30)
Note 6:  Be sure to read “Precautions for Replacement of Imager” 
on page 6-1 of Level 3 when changing the imager.
Note 6:  イメージャの交換時はLevel3の6-1ページ、“イメージャ
交換時の注意” を必ずお読みください。
DSC-RX100_L2
2-5
2-1-3. BTH SECTION
ns : not supplied
Ref. No. 
Part No. 
Description
Ref. No. 
Part No. 
Description
 101 
4-433-889-01  WINDOW 
(500), 
AF
  102 
A-1887-587-A  RL-136 BOARD, COMPLETE (Note 1, 3)
  103 
4-433-866-01 
PLATE (ROTARY BASE) (500)
  104 
1-886-112-11 
RL-137 FLEXIBLE BOARD
  105 
1-886-113-11 
BT-079 FLEXIBLE BOARD (Note 2)
 106 
X-2585-001-1  BTH 
ASSY 
(500)
  107 
4-177-693-01 
SPRING, BT DISCHARGE
  108 
4-433-864-01 
CUSHION (MIC) (LOWER) (500)
  109 
4-433-865-01 
PLATE (MIC) (500)
 BT900 
1-756-813-11 
LITHIUM RECHARGEABLE BATTERY
*BT901  1-780-826-11 
TERMINAL BOARD, BATTERY
 MIC901 1-542-931-11  MICROPHONE 
UNIT
  #275 
4-433-882-11 
TAPPING (1.4) (ECOLOGY)
Note
Note 1:  Refer to “Assembly-4: Precaution During RL-136 Flexible Board 
Installation”.
Note 2:  Refer to “Assembly-5: Precaution During BT-079 Flexible Board 
Installation”.
Note 1:  Assembly-4: Precaution During RL-136 Flexible  Board In-
stallation  を参照してください。
Note 2:  Assembly-5: Precaution During BT-079 Flexible Board In-
stallation  を参照してください。
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換してく
ださい。
使用済み電池は、取扱指示に従って処分してください。
ST Block Section
(See page 2-6)
Claw
When assembling,
adjust the position.
#275
#275
ns
ns
102
101
103
104
108
BT900
BT901
(Note 1, 3)
(Note 2)
MIC901
109
107
105
106
: BT900 (LITHIUM RECHARGEABLE BATTERY)
  Board on the mount position.
  (See page 6-22 of Level 3) 
Screw
#275:M1.4 X 2.5 (Tapping)
(Black)
4-433-882-11
2.5
1.4
Note 3:  When this part is removed, adjustment is required.
 
For the adjustment method, refer to “Adjustment items after 
replacing parts” in the Note tab of the Adjust manual.
Note 3:  この部品を取り外したときは調整が必要です。
 
調整方法については Adjust manual の Noteタブにある Adjust-
ment items after replacing parts を参照してください。
DSC-RX100_L2
2-6
2-1-4. ST BLOCK SECTION
ns : not supplied
Ref. No. 
Part No. 
Description
Ref. No. 
Part No. 
Description
  151 
X-2585-005-1  INNER (500), CABINET (TOP) ASSY
  152 
X-2585-002-1  COVER ASSY (500), ST ALUMINUM
  153 
A-1887-668-A  ST BLOCK ASSY (500)
  154 
1-886-111-11 
FL-217 FLEXIBLE BOARD (Note)
  155 
4-433-886-01 
SHEET (500), FL FLEXIBLE
 156 
1-490-423-11 
FLASH UNIT
  157 
4-433-862-01 
STRAP (L) (500)
  158 
4-433-885-02 
COVER (500), ST
  159 
4-433-878-01 
CAP (MC) (500)
 160 
4-439-756-01  SHEET 
(ST-F)
  161 
X-2585-006-1  CABINET (FRONT) ASSY (500)
 C901 
1-118-285-11 
ALUMINIUM ELECT 35uF 330V
 C902 
1-118-284-11 
ALUMINIUM ELECT 55uF 330V
  #275 
4-433-882-11 
TAPPING (1.4) (ECOLOGY)
  #276 
3-348-998-41 
SCREW (1.4X3), TAPPING, PAN
1.  The meaning of the symbol in left figure is as follows. Be careful when you remove it.
 
◇-X
:  Solder
DISASSEMBLY
Screw
#275:M1.4 X 2.5 (Tapping)
(Black)
4-433-882-11
2.5
1.4
‘
‘
‘
DISCHARGING OF THE CHARGING CAPACITOR 
ストロボ用充電コンデンサの放電
Claw
#276
ns
(Note)
ns
ns
ns
C902
C901
#275
151
152
153
157
158
155
156
154
159
161
160
Note
Note:  Refer to “Assembly-2: Installation Method of the FL-217 Flexible 
Board”.
Note: 
Assembly-2: Installation Method of the FL-217  Flexible 
Board  を参照してください。
#276:
3.0
1.4
M1.4 X 3.0 (Tapping)
(Silver)
3-348-998-41
DSC-RX100_L2
2-7
2-1-5. CABINET (REAR) SECTION
Ref. No. 
Part No. 
Description
Ref. No. 
Part No. 
Description
  201 
4-433-881-01 
SHEET (LCD FLEXIBLE) (500)
  202 
X-2585-008-1  FRAME ASSY (500), MAIN
  203 
4-433-879-01 
SHEET (LCD) (500), RADIATION (Note 1)
  204 
1-490-435-11 
SWITCH BLOCK, CONTROL (SW63500)
  205 
X-2585-004-1  CABINET (REAR) ASSY (500)
  206 
4-433-887-01 
SHEET (PAD) (500), ADHESIVE
 207 
4-433-888-01  PAD 
(500)
  208 
4-438-327-01 
SPACER (FRAME) (500)
  209 
4-433-877-01 
SHEET (LCD (500)), ADHESIVE (Note 1)
 LCD901  1-811-695-11 
PANEL MODULE (PE5-BJD) (Note 2)
Note
Note 1:  This part cannot be reused. Replace parts that were removed 
even once during service with new ones.
Note 1:
 
この部品は再利用することができません。サービス対応時に一
度でも外した場合は新品の部品と交換してください。
202
201
205
206
207
204
LCD901
(Note 2)
Claw
 203
(Note 1)
 209
(Note 1)
 208
Note 2:  Refer to “Assembly-3: Precaution During LCD Panel Installa-
tion”.
Note 2:  Assembly-3: Precaution During LCD Panel Installation  を参
照してください。
Page of 27
Display

Click on the first or last page to see other DSC-RX100 (serv.man2) service manuals if exist.

RANDOM: