Sony DSC-RX100 (serv.man2) Service Manual ▷ View online
DSC-RX100_L2
1-2
– ENGLISH –
3) Search the model whose new Destination Data file you want to get on the TISS homepage.
When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered.
(Example) Destination File For DSC-WX50.zip
Furthermore, the version supported by the Destination Data file is shown in the Remarks column.
Note : If the Destination Data file has not been updated, contact the Service Headquarters.
4) Download the Destination Data file of the relevant model and unzip the file.
5) Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual.
Click the [START] button.
6) Click the [File Update] button in the window.
7) A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
8) When the file has been successfully added, the following window opens.
9) Check the Destination Ver. window and confirm that the version has been updated.
Destination Ver. window
DSC-RX100_L2
1-3
– ENGLISH –
1-3. NOTES ON REMOVING/INSTALLING THE IMAGER BOARD (CD-847 FLEXIBLE BOARD)
When the CD-847 Flexible Board (Imager) is mounted to the lens, shift and tilt adjustment is made with Spacer Plates.
When removing the CD-847 Flexible Board, pay attention to the following.
When removing the CD-847 Flexible Board, pay attention to the following.
(1) When the lens is not replaced
Example: In the case of disassembly, cleaning, or replacement of the CD-847 Flexible Board (Imager)
• Check and record the size of the built-in three Spacer Plates and store them so as not to lose them.
• When assembling the CD-847 Flexible Board, be sure to install the Spacer Plates to their original locations.
• When assembling the CD-847 Flexible Board, be sure to install the Spacer Plates to their original locations.
Size
0.xx
Note
Be careful not to lose the Spacer Plates.
If any Spacer Plate is lost or their previous positions are not sure, repeatedly take a photo and check that there is no local defocus.
Be careful not to lose the Spacer Plates.
If any Spacer Plate is lost or their previous positions are not sure, repeatedly take a photo and check that there is no local defocus.
Selecting appropriate Spacer Plates
is needed.
(2) When the lens is replaced
• Check the size of the built-in three Spacer Plates. If the thickness of a Spacer Plate is not 0.20, discard the Spacer Plate.
• Prepare three Spacer Plates B (t = 0.2) (Sony Part No.: 4-410-540-01) and install them to the new lens.
• Prepare three Spacer Plates B (t = 0.2) (Sony Part No.: 4-410-540-01) and install them to the new lens.
0.20
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis func-
tion starts working, and displays on the LCD screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
tion starts working, and displays on the LCD screen what to do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the LCD screen shows
a 4-digit display consisting of an alphabet and numbers, which blinks at
3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in
which the problem occurred, and “detailed code” of the problem.
a 4-digit display consisting of an alphabet and numbers, which blinks at
3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in
which the problem occurred, and “detailed code” of the problem.
0 0
3 2
C
Repaired by:
Refer to “1-4-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....Format the “memory card”.
32 ....Turn on power again.
13 ....Format the “memory card”.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
LCD screen
DSC-RX100_L2
1-4
– ENGLISH –
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
1
3
0
1
The internal memory has experienced a
media error.
media error.
Turn the power off and on again.
The internal memory has experienced a
format error.
format error.
Turn the power off and on again.
Memory card is unformatted.
Format the memory card.
Memory card is broken.
Insert a new memory card.
Memory card type error.
Insert a supported memory card.
The camera cannot read or write data on
the memory card.
the memory card.
Turn the power off and on again, or taking out and inserting the memory
card several times.
card several times.
C
3
2
0
1
Trouble with hardware.
Turn the power off and on again.
E
4
1
0
0
Abnormality of network control.
Turn the power off and on again.
E
4
1
0
1
Abnormality of network control device.
Turn the power off and on again.
E
6
1
0
0
Difficult to adjust focus.
(Cannot initialize focus)
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does not recover, check
the focus reset sensor of lens block (pin 8, 0 of CN406 on the SY-335
board). If it is OK, check the focus motor drive IC (IC403 on the SY-335
board).
the focus reset sensor of lens block (pin 8, 0 of CN406 on the SY-335
board). If it is OK, check the focus motor drive IC (IC403 on the SY-335
board).
E
6
1
1
0
Zoom operations fault.
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Retry turn the power on by the power switch. Check the zoom reset sensor
of lens block (pin 1 of CN406 on the SY-335 board) when zooming is
performed when the zoom button is operated. If it is OK, check the zoom
motor drive IC (IC401 on the SY-335 board).
of lens block (pin 1 of CN406 on the SY-335 board) when zooming is
performed when the zoom button is operated. If it is OK, check the zoom
motor drive IC (IC401 on the SY-335 board).
E
6
1
3
0
Reset position detection error on the step-
per iris initializing.
per iris initializing.
Turn power off and turn power on again.
E
6
2
0
2
Abnormality of IC for steadyshot.
Check or replacement of the IC for steadyshot (IC401 on the SY-335
board).
board).
E
6
2
1
0
Lens initializing failure.
Check or replacement of the IC for steadyshot (IC401 on the SY-335
board).
board).
E
6
2
1
1
Lens overheating (PITCH).
Check the HALL element (PITCH) of optical image stabilizer (pin ef, eh
of CN406 on the SY-335 board). If it is OK, check PITCH angular velocity
sensor (SE401 on the SY-335 board) peripheral circuits.
of CN406 on the SY-335 board). If it is OK, check PITCH angular velocity
sensor (SE401 on the SY-335 board) peripheral circuits.
E
6
2
1
2
Lens overheating (YAW).
Check the HALL element (YAW) of optical image stabilizer (pin ea, ed
of CN406 on the SY-335 board). If it is OK, check YAW angular velocity
sensor (SE401 on the SY-335 board) peripheral circuits.
of CN406 on the SY-335 board). If it is OK, check YAW angular velocity
sensor (SE401 on the SY-335 board) peripheral circuits.
E
6
2
2
0
Abnormality of thermistor.
Check the OIS temp sensor of optical image stabilizer (pin qa of CN406
on the SY-335 board).
on the SY-335 board).
E
9
1
0
1
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note 1)
E
9
2
0
0
Non-standard battery is used.
Use the specified battery.
E
9
4
0
0
Internal memory fault.
Turn the power off and on again.
E
9
5
0
0
GPS hardware error.
Turn the power off and on again.
E
9
5
0
1
Acceleration sensor hardware error.
(GPS hardware error)
(GPS hardware error)
Turn the power off and on again.
E
9
5
0
2
Electronic compass hardware error.
(GPS hardware error)
(GPS hardware error)
Turn the power off and on again.
Note 1: After repair, be sure to perform “1-5. PROCESS AFTER FIXING FLASH ERROR”.
Note 2: Functions of codes with * mark are not provided in this unit.
Note 2: Functions of codes with * mark are not provided in this unit.
*
*
*
*
1-5. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed
automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated.
automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated.
Method for Initializing the Flash Error Code
Reset Flash Error using the Flash Error Repair Tool Ver_[].[].exe.
*
*
DSC-RX100_L2
1-5
– JAPANESE –
1-1. SY-335基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。
Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。
リストアデータ
補修用基板と交換する時，交換前の基板よりデータを取得してください。
データの取得はAdjust StationからAdjust Manualを起動させて「RESTORE DATA」を実行させてください。
本機で取得されるデータは下記になります。
データの取得はAdjust StationからAdjust Manualを起動させて「RESTORE DATA」を実行させてください。
本機で取得されるデータは下記になります。
･ USB SERIAL No.
･ Angular Velocity Sensor sensitivity adjustment
･ AWB standard data input & check, Color reproduction check
･ Strobe adjustment
･ Angular Velocity Sensor sensitivity adjustment
･ AWB standard data input & check, Color reproduction check
･ Strobe adjustment
PlayMemories Homeについて
本機の内蔵メモリー内にはPlayMemories Homeが書き込まれています。
補修用SY-335基板は，PlayMemories Homeが書き込まれた状態で供給されます。
補修用SY-335基板は，PlayMemories Homeが書き込まれた状態で供給されます。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
Adjust StationからAdjust Manualを起動させて「USB SERIAL No. INPUT」を実行させてください。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
Adjust StationからAdjust Manualを起動させて「USB SERIAL No. INPUT」を実行させてください。
角速度センサ
補修用基板と交換する時，角速度センサ（SE401）の感度表示を書き留めてください。
Adjust StationからAdjust Manualを起動させて「Angular velocity sensor sensitivity adj.」を実行させてください。
Adjust StationからAdjust Manualを起動させて「Angular velocity sensor sensitivity adj.」を実行させてください。
SE401
SY-335 BOARD (SIDE B)
Type A:
Type B:
Y P
Y P
P: PITCH 感度表示
Y: YAW 感度表示
Note：SY-335基板のSE401感度表示は補修用基板にしか記載されておりません。
1-2. Destination Data ファイルの追加について
Adjust manual に含まれる Destination Data ファイルが古い場合，
「DESTINATION DATA WRITE」 が実行できないことがあります。
その場合は，下記の手順を参考にして， TISS ホームページより新しい Destination Data ファイル を入手してください。
Note 1： この機種で仕向け設定を行うには，DSC-WX50シリーズの Adjust manual がインストールされている必要があります。
先に DSC-WX50 シリーズの Adjust manual をインストールしてください。
Note 2： 手順中の画像は実際と異なる場合があります。
1) 使用している Adjust manual の Destination Data ファイルが古い場合， Fig. 1 のようなウインドウが表示される。
[OK] ボタンをクリックする。
Fig.
1
2) Destination Data Write ウインドウが表示される。
Adjust manual の保持している Destination Data ファイル のバージョンを確認する。
Destination Ver. ウインドウ
Click on the first or last page to see other DSC-RX100 (serv.man2) service manuals if exist.