Sony DSC-RX100 (serv.man2) Service Manual ▷ View online
DSC-RX100_L2
1-10
1-8. LINEAR GUIDE TUBE (B) AND CAM TUBE REPLACING METHOD
Removal
1. Remove the five screws and the Z Retainer.
2. Remove the Sensor.
1. Remove the five screws and the Z Retainer.
2. Remove the Sensor.
Zoom Gear Assy (1560)
Screw
Rear Tube Mirror Block
Screws
Screw
Z Retainer
Screw
3. Remove the Zoom Gear Assy (1560).
4. Remove the FPC Retainer and the screw.
5. Disconnect the Flexible Board (Focus) from the connector.
4. Remove the FPC Retainer and the screw.
5. Disconnect the Flexible Board (Focus) from the connector.
6. Remove the Rear Tube Mirror Block.
7. Disconnect the Flexible Boards from the connectors and remove the LF-155 Flexible Board.
LF-155 Flexible Board
Flexible board (Focus)
Sensor
Connector
FPC Retainer
Hook
Hook
Boss
Be careful so that the Rear Tube
Mirror Block is not caught.
Connectors
Flexible
Boards
Solders
LF-155 Flexible Board
FG Retainer
Sensors
Hook
Rib
Boss
Rib
Installation
1. Install the two Sensors to the Zoom Gear Assy (1560), and then attach the FG Retainer.
2. Solder the Zoom Gear Assy (1560) to the LF-155 Flexible Board at two locations.
1. Install the two Sensors to the Zoom Gear Assy (1560), and then attach the FG Retainer.
2. Solder the Zoom Gear Assy (1560) to the LF-155 Flexible Board at two locations.
Screw
Zoom Gear Assy (1560)
3. Install the Zoom Gear Assy (1560).
4. Install the screw.
Zoom Gear Assy (1560)
DSC-RX100_L2
1-11
8. Turn the Naruto Gear in the arrow direction to extend the Lens Barrel to the center of TELE and WIDE.
9. Remove the Flexible Boards from the Ribs and the Boss and store the Flexible Boards in the Lens Barrel.
9. Remove the Flexible Boards from the Ribs and the Boss and store the Flexible Boards in the Lens Barrel.
10. Turn the Naruto Gear in the arrow direction to return to the WIDE end.
11. Remove the Naruto Gear.
12. Detach the Stationary Tube.
11. Remove the Naruto Gear.
12. Detach the Stationary Tube.
13. Turn the Cam Tube in the arrow direction to detach the 1 Group Frame Block Assy.
14. Detach the 1 Group Frame Block Assy from the Straight Tube (A) Block Assy.
14. Detach the 1 Group Frame Block Assy from the Straight Tube (A) Block Assy.
1 Group Frame Block Assy
Straight Tube (A)
Block Assy
Block Assy
1 Group Frame
Block Assy
Block Assy
Flexible
Boards
Boards
Stationary Tube
Naruto Gear
Naruto Gear
Naruto Gear
Boss
Rib
Rib
Rib
17. Match the marks of the Cam Tube and the Linear Guide Tube (B).
18. Detach the Linear Guide Tube (B) from the Cam Tube.
18. Detach the Linear Guide Tube (B) from the Cam Tube.
Cam Tube
Cam Tube
Linear Guide Tube (B)
Linear Guide Tube (B)
15. Set the Mark of the Linear Guide Tube (B) at the first gear tooth of the Cam Tube.
16. Remove the 3 Group Frame Block Assy and the 2 Group Frame Block Assy.
16. Remove the 3 Group Frame Block Assy and the 2 Group Frame Block Assy.
2 Group Frame Block Assy
3 Group Frame Block Assy
Mark
Mark
Mark
DSC-RX100_L2
1-12
Linear Guide Tube (B)
Cam Tube
CAV No.
Linear Guide Tube (B)
Installation
1. While matching the marks of the Linear Guide Tube (B) and the Cam Tube, assemble these parts.
1. While matching the marks of the Linear Guide Tube (B) and the Cam Tube, assemble these parts.
2. Set the Mark of the Linear Guide Tube (B) at the first gear tooth of the Cam Tube.
3. Install the 2 Group Frame Block Assy at a position where the Mark of the Linear Guide Tube (B) matches CAV No. of
the 2 Group Frame Block Assy.
4. Install the 3 Group Frame Block Assy at a position where the Mark of the Linear Guide Tube (B) matches the hole of the
3 Group Frame Block Assy.
3. Install the 2 Group Frame Block Assy at a position where the Mark of the Linear Guide Tube (B) matches CAV No. of
the 2 Group Frame Block Assy.
4. Install the 3 Group Frame Block Assy at a position where the Mark of the Linear Guide Tube (B) matches the hole of the
3 Group Frame Block Assy.
5. Set the Mark of the Linear Guide Tube (B) at the first gear tooth of the Cam Tube.
6. Match the Mark of the Cam Tube with the concave portion of the 1 Group Frame Block Assy.
7. Install the Cam Tube and the 1 Group Frame Block Assy.
6. Match the Mark of the Cam Tube with the concave portion of the 1 Group Frame Block Assy.
7. Install the Cam Tube and the 1 Group Frame Block Assy.
2 Group Frame Block Assy
3 Group Frame Block Assy
1 Group Frame
Block Assy
Block Assy
Cam Tube
Cam Tube
Cam Tube
Linear Guide Tube (B)
Cam Tube
Linear Guide Tube (B)
Mark
Mark
Mark
Concave
portion
portion
Mark
Hole
8.
9.
10. Turn the Cam Tube counterclockwise to the maximum extent.
11.
12. Check that the five Helicoids are engaged with the grooves.
Cam Tube
Straight Tube (A)
Block Assy
Block Assy
Stationary Tube
Near the
Naruto Gear
Naruto Gear
Concave
portion
portion
CAV No.
Straight Tube (A)
Block Assy
Block Assy
Match CAV No. inside the Straight Tube (A) Block Assy with the concave portion position of the 1 Group
Frame Block Assy.
Frame Block Assy.
Push the Straight Tube (A) Block Assy in the arrow direction with the Cam Tube turned clockwise to the
maximum extent.
maximum extent.
While matching the Helicoid near the Mark with the groove near the Naruto Gear of the Stationary
Tube, assemble the Stationary Tube.
Tube, assemble the Stationary Tube.
Helicoid
Mark
DSC-RX100_L2
1-13
13. Install the Naruto Gear.
14. Turn the Naruto Gear in the arrow direction to extend the Lens Barrel to the center of TELE and WIDE.
14. Turn the Naruto Gear in the arrow direction to extend the Lens Barrel to the center of TELE and WIDE.
15. Pull the Flexible Boards out of the Lens Barrel and fix the Flexible Boards with the Boss and the Ribs.
16. Turn the Naruto Gear in the arrow direction to return to the WIDE end.
16. Turn the Naruto Gear in the arrow direction to return to the WIDE end.
17. Install the LF-155 Flexible Boards.
18. Connect the Flexible Boards to the connectors.
18. Connect the Flexible Boards to the connectors.
19. Install the Rear Tube Mirror Block.
Rear Tube Mirror Block
LF-155 Flexible Board
Naruto Gear
Naruto Gear
Flexible
Boards
Boards
Boss
Rib
Rib
Rib
Naruto Gear
Hook
Boss
Connectors
Flexible
Boards
Boards
Rib
Rib
Rear Tube Mirror Block
20. Connect the Flexible Board (Focus) to the connector.
21. Install the FPC Retainer and a screw.
22. Install the Zoom Gear Assy (1560).
21. Install the FPC Retainer and a screw.
22. Install the Zoom Gear Assy (1560).
Zoom Gear Assy (1560)
Screw
23. Install the Sensor.
24. Install five screws and the Z Retainer.
24. Install five screws and the Z Retainer.
Screws
Screw
Z Retainer
Screw
Flexible Board (Focus)
Connector
FPC Retainer
Hook
Sensor
Rib
Boss
Rib
Click on the first or last page to see other DSC-RX100 (serv.man2) service manuals if exist.