DOWNLOAD Sony DSC-R1 (serv.man2) Service Manual ↓ Size: 5.7 MB | Pages: 66 in PDF or view online for FREE

2-1

DSC-R1_L2

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, dont’ press down at wire of connector.

It is possible that a wire is snapped.

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

The charging capacitor (C104) of the ST-128 flexible board is
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand.  The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k

Ω

 /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.

1 k

Ω

/1 W

Wrap insulating tape.

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between the two points 
with the short jig about 10 seconds.

R:1 k

Ω

/1 W 

(Part code: 1-215-869-11)

P2 tapping screw

Position of the screw

Position of the screw Ornamental plate

1 group lens

1 group spacer

Filter screw frame

When the lens block is disassembled, be sure to disassemble it
with the set erected.
The 1 group lens and the 1 group spacer will be removed, if the
lens block is disassembled with the set laid down as shown in
the right figure.

DSC-R1_L2

2-3

2-4

The following flow chart shows the disassembly procedure.

1

Open the LCD.

2

P2 screw (M2x4) (black) 

x8

3

Remove the cabinet (rear) block.

4

Flexible board 

x1

5

Cabinet (rear) block

1

Remove the fuse replacement caution label.

2

Flexible board 

x4

3

P2 screw (M2x4) (black) 

x4

4

Center block assembly

1

Flexible board 

x2

2

Cabinet upper assembly

3

Discharging the Capacitor.

1

Claw 

x2

2

Remove the cabinet 
(side) block assembly.

3

Flexible board 

x1

4

Cabinet (side) block assembly

5

Flexible board 

x2

6

Claw 

x2

7

EVF block assembly

1

Connector 

x2

2

Fuse replacement caution label

3

P2 tapping screw (M1.7x3) (silver) 

x6

4

Boss 

x1

5

SY board

1

Open the LCD.

2

P2 screw (M2x4) (black) 

x2

3

Claw 

x4

4

LC case (L)

5

Tape (A) 

x1

6

Flexible board 

x2

7

P2 tapping screw (M1.7x3) (silver) 

x1

8

PD board

9

P2 tapping screw (M1.7x4) (black) 

x2

0

P2 tapping screw (M1.7x4) (black) 

x4

qa

LC retainer

qs

LC case block

qd

LCD901, D901

2

2

2

2

2

3

4

5

1

3

4

3

3

3

1

2

2

1

1

5

2

3

6

7

4

2

3

1

2

3

5

6

7

8

0

0

qa

9

qs

qd

6

4

3

2

4

5

1

DSC-R1_L2

2-5

2-6

Fold

Fold

Fold

Adhesive tape

Adhesive tape

Adhesive tape

A

B

C

1

The 

A

 and 

A

, 

B

 and 

B

, 

C

 and 

C

 section 

are united and an angle is folded.

2

An angle is folded.

6

Set the hinge (ZZ) assembly and PN-002 flexible board.

7

Screw (M1.7x3) (black)

PN-002 flexible board

LCFPC holder

Claw

Claw

Claw

Claw

8

LC hinge cover (L)

9

LC hinge cover (U)

Claw

Claw

Claw

Claw

5

Roll the t

he PN-002 flexible board 1.5 times, 

in the direction of arrow

 

A

.

5

Set the LCFPC holder 
and 

hinge (ZZ) assembly

.

5

Set the LCFPC holder 
and 

PN-002 flexible board.

A

Hinge (ZZ) assembly

Boss

Claw

Hinge (ZZ) 
assembly

2-7E

DSC-R1_L2

1

Lifting up the BT lid.

2

Insert the flat blade screwdriver 
between BT lid and BT hige plate.

3

Claw 

x1

BT lid

1

3

2

5

4

Claw 

x1

5

BT lid

BT hige plate

4

FINDER AUTO

LCD

FRAMING

CF

PREVIEW

1

Set the mode dial section as shown in 
figure.

2

Set three switchies as shown in figure.

3

BK board

4

P2 tapping screw (M1.7x4) (black) 

x4

5

Connector 

x1

6

Tape (Z) 

x1

7

Set the control switch block as shown in figure.

8

Control switch block

9

Flexible board 

x1

0

P2 tapping screw (M1.7x4) (black) 

x3

1

3

4

5

6

7

9

0

0

8

2

2

Mark

Mark

Mode dial section