DOWNLOAD Sony DSC-R1 (serv.man2) Service Manual ↓ Size: 5.7 MB | Pages: 66 in PDF or view online for FREE

1-1

DSC-R1_L2

•

C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)

•

E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.

Display Code

  C:32:ss

  C:13:ss

Countermeasure

Turn the power off and on again.

Format the recording medium.

Insert a new recording medium.

Cause

Trouble with hardware.

Unformatted recording medium is inserted.

Recording medium is broken.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR,
CF CARD ERROR

  E:61:ss

  E:91:ss

Checking of lens drive circuit.

When failed in the focus and zoom
initialization.

Checking of flash unit or replacement
of flash unit.

—

Abnormality when flash is being
charged.

1-2

DSC-R1_L2

When you replace to the repairing board, the written data of repairing board also might be changed to original setteing because of broadcast
system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code is right. If not, rewrite
to the right value.

Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).
4) Select page: 40, address: 38, and set data: 00.
5) Click 

[Save]

 on the SEUS screen.

6) Select page: 80, address: 34, and check that the data is “00”.
7) Select page: 80, address: 30, and check that the data is “00”.
8) Select page: 00, address: 01, and set data: 00.

Address

00

00

01

01

8D

A2

4F

4F

Page

Data

NTSC

PAL

1-3E

DSC-R1_L2

Dust on the optical surface of the CMOS block causes it to be shot as a black spot in the picture. To prevent dust from attaching, perform the
work, taking care of the following points:

•

Perform the replacement work at a less dusty place.

•

Perform the replacement work quickly. Do not leave the parts to stand.

•

Perform the work with the opening of Lens block, CMOS block facing down, if practicable.

•

Do not touch the optical surface of the CMOS block and Optical Filter block.

•

Do not put the Optical Filter block directly on the desk.

After assembling the set, inspect by the following method to check if dust is shot.

Switching setting:
1) Mode dial ···························································· A (Aperture)
2) Aperture ·············································································· F16
3) Zoom ring ································································ TELE end
4) FOCUS switch ······················································· MANUAL
5) Manual focus ring ·································································

∞

6) Image size ·············································· 10M (MENU setting)

Method:
1) Shoot a full-white subject (such as white paper) at a distance of several cm at a light place.

(Pattern box with clear chart, full-white screen on the PC monitor with the increased brightness are also possible.)

2) Play back the shot picture in 100% size on the PC to check that no black spot is found.

If dust exists, perform the cleaning as follows.

1) Blow it off by the air.
2) Wipe the CMOS block and Optical Filter block if air blow failed to clear the dust.

Wipe the CMOS block and Optical Filter block gently in one-way direction using the nonwoven cloth wiper for cleaning (low dust
generation, soft type such as Bemcot or Dusper) moistened with small quantity of anhydrous alcohol.

3) Check with a loupe that the dust was cleared.
4) After assembly, conduct the inspection again (shooting test).

Optical filter block

Lens assembly repair

CMOS block assembly

P2 tapping screw

Seal rubber_R

DSC-R1_L2