DOWNLOAD Sony DSC-P1 (serv.man3) Service Manual ↓ Size: 1.68 MB | Pages: 36 in PDF or view online for FREE

1

Three screws
(M1.7)

2

SW-349 board

4

Two claws

1

Screw

2

Light guide plate block

3

Two claws

5

LCD module

3

Two screws
(M1.7)

2

Three screws
(M1.7)

4

PD-137 board

6

Flexible board
(ZM-26 board)
(CN882)

1

Two flexible boards
(CN805, 806)

5

Flexible board
(SW-349 board)
(CN884)

1

Two screws
(M1.7)

2

ZM sheet metal

3

ZM-26 board

Adhesive sheet (A)
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]

Light interception sheet (F)

1

Peel off the light interception sheet (F).

2

From the inner cabinet (rear) assembly, remove
the aluminum cabinet (rear) assembly stuck with 
adhesive sheet (A) at two places.

Aluminum cabinet (rear)
assembly

adhesive sheet (A)

3

Insert new aluminum cabinet (rear) assembly,
aligning with the inner cabinet. In such a case,
make sure that the adhesive sheet (A) is affixed
on the inner cabinet side. If adhesive sheet (A)
 is not present or adhesive force is reduced, 
affix adhesive sheet (A) (3-064-219-01) to the places 
shown below before insertion.

LCD cover

5

Affix the LCD cover, aligning with the frame of 
aluminum cabinet.

Note: At this time, do not touch the back of 

LCD cover. The back surface with 
a spcial treatment is easily affected
with the pollution.

Adhesive sheet (P)

4

Affix adhesive sheet (P), aligning with the frame 
of aluminum cabinet.

Light interception sheet (F)

6

As shown below, affix the light
interception sheet (F), aligning with
the positioning boss.

Parallel pin (dia. 1.6 

×

 5)

3

Pull off the forcibly fitted parallel pin (dia. 1.6 

×

 5)

in the direction of arrow 

A

.

A

Adhesive sheet (A)
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]

Light interception sheet (F)

1

Peel off the light interception sheet (F).

2

From the aluminum cabinet (rear) assembly, remove
the inner cabinet (rear) assembly stuck with 
adhesive sheet (A) at two places.

Inner cabinet (rear) assembly

4

Pull the jack cover off the inner cabinet (rear).

Jack cover

Inner cabinet (rear) assembly

5

Insert the jack cover into new inner 
cabinet (rear) assembly.

Jack cover

Parallel pin (dia. 1.6 

×

 5)

6

Forcibly fit the Parallel pin (dia. 1.6 

×

 5).

Aluminum cabinet (rear)
assembly

adhesive sheet (A)

7

Check if adhesive sheet (A) remains on the aluminum 
cabinet side, and if so, remove it. Peel stripping sheet off 
the adhesive sheet (A) at two places in the inner cabinet (rear) 
assembly. Insert the inner cabinet (rear) assembly, 
aligning with the aluminum cabinet.

Light interception sheet (F)

8

As shown below, affix the light
interception sheet (F), aligning with
the positioning boss.

Parallel pin (dia. 1.6 

×

 5)

3

Pull off the forcibly fitted parallel pin (dia. 1.6 

×

 5)

in the direction of arrow 

A

.

A

Adhesive sheet (A)
[Between inner cabinet (rear) assembly
and aluminum cabinet (rear) assembly]

Light interception sheet (F)

1

Peel off the light interception sheet (F).

2

From the aluminum cabinet (rear) assembly, remove
the inner cabinet (rear) assembly stuck with 
adhesive sheet (A) at two places.

Inner cabinet (rear) assembly

4

Pull the jack cover off the inner cabinet (rear).

Jack cover

Inner cabinet (rear) assembly

5

Insert new jack cover into the inner 
cabinet (rear) assembly.

Jack cover

Parallel pin (dia. 1.6 

×

 5)

6

Forcibly fit the Parallel pin (dia. 1.6 

×

 5).

Aluminum cabinet (rear) assembly

7

Insert the inner cabinet, aligning with the aluminum cabinet. 
In such a case, if adhesive sheet (A) is not present or 
an adhesive force is reduced, affix adhesive sheet (A) 
(3-064-219-01) before insertion.

Light interception sheet (F)

8

As shown below, affix the light
interception sheet (F), aligning with
the positioning boss.