DOWNLOAD Sony DSC-F717 (serv.man4) Service Manual ↓ Size: 521.86 KB | Pages: 56 in PDF or view online for FREE

6-3

Ref. No.

J-1

J-2

J-3

J-4

J-5

J-6

J-7

J-8

Name

Filter for color temperature correction (C14)

Pattern box PTB-450

Color bar chart for pattern box

Adjusting remote commander (RM-95 upgraded).
(Note 1) 

Siemens star chart

Clear chart for pattern box

CPC-12 jig

Minipattern box

Parts Code

J-6080-058-A

J-6082-200-A

J-6020-250-A

J-6082-053-B

J-6080-875-A

J-6080-621-A

J-6082-436-A

J-6082-353-B

Usage

Auto white balance adjustment/check
White balance adjustment/check

For checking the flange back

For connecting the adjusting remote commander
For adjusting the LCD, EVF block

J-10

Extension cable (39 P, 0.3 mm)

J-6082-448-A

For extension between the CD-408 board (CN301) and
the SY-080 board (CN101)

J-11

Extension cable (39 P, 0.3 mm)

1-686-180-11

For extension between the SY-080 board (CN701, 702) 
and the FR-194 board (CN301, 302)

For adjusting the flange back

J-9

Back ground paper  

J-2501-130-A For adjusting the strobe 

• Oscilloscope

• Color monitor

• Vectorscope

• Regulated power supply

• Digital voltmeter

• Frequency counter

• Calculating machine capable of calculating hexadecimal numbers.

If the micro processor IC in the adjusting remote
commander is not the new micro processor (UPD7503G-
C56-12), The pages cannot be switched. In this case,
replace with the new micro processor (8-759-148-35).

J-1

J-5

J-2

J-6

J-7

J-3

J-4

J-8

J-9

J-10

J-11

6-4

For details of how remove the cabinet and boards, refer
to “2. DISASSEMBLY”.

When performing only the adjustments, the lens block
and boards need not be disassemble.

1) Connect the equipment for adjustments according to Fig. 6-1-

6.

2) Connect the Adjusting remote commander to the FR-194 board

CN305 via CPC-12 jig (J-6082-436-A).  (See Fig. 6-1-3)

Setting the “Forced CAMERA mode power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 21, set data: 07, and press

the PAUSE button of the adjusting remote com-
mander.
The above procedure will enable the camera power
to be turned on.  After completing adjustments, be
sure to exit the “Forced CAMERA mode power ON
Mode”.

Exiting the “Forced CAMERA mode power ON Mode”
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 21, set data: 00, and press

the PAUSE button of the adjusting remote com-
mander.

3) Select page: 0, address: 01, and set data: 00.

The capacitor which is used as power supply of flashlight is charged
with 200 V to 300 V voltage.  Discharge this voltage before start-
ing disassembly in order to protect service engineers from electric
shock during disassembly.

Discharge procedure
1. Remove the FR-194 board, and disconnect the harness from

CN404 on the BT-015 board.

2. Fabricate the short jig as shown in Fig. 6-1-5 locally by your-

self.  Connect the short jig to the pin 1 and pin 2 of CN404
on the BT-015 board.  Allow ten seconds to discharge the volt-
age.

1 k

Ω

/1 W

Wrap insulating tape.

R:1 k

Ω

/1 W

 

(Part code: 
1-215-869-11)

CN404

Harness

CPC cover

CPC-12 jig
(J-6082-436-A)

FR-194 board
CN305

22

1

Front of the lens

Pattern box

L

L=About 30 cm

6-5

CONTROL SWITCH BLOCK
(FZ51050)

MANUAL FOCUS BLOCK
(MF51050)

LENS BLOCK

CD-408 BOARD

SY-080

BOARD

FR-194 BOARD

BT-015

BOARD

AL-013 BOARD

PD-179 BOARD

PANEL UNIT

BACK LIGHT

SW-379 BOARD

EVF BLOCK

LB-082

BO

ARD

CN704

CN703

CN203

CN305

CN404

CN403

CN705

CN801

CN851

CN704

CN301

CN302

Need not connected

Need not
connected

Extension cable
(1-686-180-11)

AC IN

Vectorscope

CN702

CN701

Color
monitor

Video
(yellow)

Audio
(black)

A/V OUT jack

Terminated

75 

Ω

AC power
adaptor

DC IN jack

Extension cable
(J-6082-448-A)

Must be connected to Flash unit
when performing the “Strobe White
Balance Adjustment”.

CN702

CN304 CN309

CN302

CN301

CPC-12 jig
(J-6082-436-A)

Adjusting
remote
commander

To
MIC/
SPEAKER
UNIT
(TY-014)

To MS SOCKET

To
CONTROL SWITCH BLOCK
(PW51050)

CN306

CN001

CN401

CN308

CN101

CN701

CN303

6-6

Unless otherwise specified, set the switches as follows and per-
form adjustments.
1. Mode Dial .......................................... CAMERA
2. FOCUS switch

(FZ51050 block S308) ....................... MANUAL

3. EXPOSURE button

(PW51050 block S404) ..................... 0EV

4. DISPLAY button

(SW-379 board S355) ........................ OSD OFF

5. WHT BAL

(FZ51050 block S304) ....................... AUTO

6. P.EFFECT (Menu display) ................ OFF
7. VIDEO OUT (SET UP setting) ......... NTSC

Basically carry out adjustments in the order given.

1) Color bar chart (Standard picture frame).

When performing adjustments using the color bar chart, ad-
just the picture frame as shown in Fig. 6-1-7. (Standard pic-
ture frame)

2) Clear chart (Standard picture frame)

Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations dur-
ing this time)

3) Chart for flange back adjustment

Join together a piece of white A0 size paper (1189mm 

×

 841

mm) and a piece of black paper to make the chart shown in
Fig. 6-1-8.

Use a non-reflecting and non-glazing vellum paper.  The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.

H

A=B

A B

B A

Enlargement

V

C=D

Electronic beam scanning frame

Fig. b (monitor TV picture)

CRT picture frame

B

A

Difference in level

Y

e

llow

Cyan

Green

White

Magenta

Red

Blue

Y

e

llow

Cyan

Green

White

Magenta

Red

Blue

D

C

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig a
and the monitor TV display shown in Fig. b.

Black

White

841 mm

1189 mm