Sony DSC-F55V (serv.man2) Service Manual ▷ View online
5-6
1-1-4.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform
adjustments.
adjustments.
1.
DEMO MODE (SETUP menu) ....................................... OFF
2.
DIGITAL ZOOM (MS block) .................................. Wide end
3.
WHITE BALANCE (CAMERA menu) ...................... AUTO
4.
FLASH LEVEL (CAMERA menu) ....................... NORMAL
5.
EXPOSURE (CAMERA menu) ...................................... 0EV
6.
P. EFFECT (EFFECT menu) ........................................... OFF
7.
PROGRAM AE (HF block) ......................................... AUTO
(No mark indicated on LCD)
8.
FOCUS (Menu) ............................................................ AUTO
(No mark indicated on LCD)
9.
DISPLAY (HF block) ...................................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-6. (Standard picture
frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-6. (Standard picture
frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 5-1-7 using A0 size (1189 mm
Make the chart shown in Fig. 5-1-7 using A0 size (1189 mm
×
841 mm) black and white vellum paper.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Video terminal
output waveform
Fig. b (monitor TV picture)
Fig. a
White
Black
841mm
1189mm
Color bar chart (Color reproduction adjustment frame)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the monitor TV display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the monitor TV display shown in Fig. b.
Fig. 5-1-6.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
Fig. 5-1-7.
5-7
00 to 0F
10
11 to 42
43
44 to 61
62
63
64 to 66
67
68 to 6B
6C
6D
6E
6F
70 to 7C
7D
7E to 89
8A
8B
8C to 8F
90
91
92
93
94
95 to 97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6 to CF
D0
D1
D2
D3
00
00
00
00
00
00
80
88
AD
C2
CD
BC
80
B9
B7
Test mode
Fixed data-1 (Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1 (Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1 (Initialized data)
Flash unit emergency
Fixed data-1 (Initialized data)
Recording counter
Recording counter/MC CAM (SY-59
board IC501) emergency
Fixed data-1 (Initialized data)
Fixed data-2
Fixed data-1 (Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1 (Initialized data)
Battery end adj.
Fixed data-1 (Initialized data)
Fixed data-2
(Modified data. Copy the data built in
the same model.)
Fixed data-1 (Initialized data)
Fixed data-2
Fixed data-1 (Initialized data)
Fixed data-2
Fixed data-1 (Initialized data)
Bright adj. (LCD)
Color adj. (LCD)
White balance adj. (LCD)
Address
Remark
Initial value
1-2.
INITIALIZATION OF B, D, E, F, 7 PAGE DATA
1-2-1.
INITIALIZATION OF D PAGE DATA
1. Initializing the D Page Data
Note:
If the D page data has been initialized, the following adjustments
need to be performed again.
1) Modification of D page data
2) LCD system adjustments
3) Battery end adjustments
need to be performed again.
1) Modification of D page data
2) LCD system adjustments
3) Battery end adjustments
Adjusting page
D
Adjusting Address
10 to EF
Initializing Method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 2, address: 03, and set data: 01.
3)
Select page: 2, address: 00, and set data: 2D.
4)
Select page: 2, address: 01, set data: 2D, and press the PAUSE
button of the adjustment remote commander.
button of the adjustment remote commander.
5)
Select page: 2, address: 02, and check that the data changes to
“01”.
“01”.
6)
Perform “Modification of D Page Data”.
2. Modification of D Page Data
If the D page data has been initialized, change the data of the “Fixed
data-2” address shown in the following table by manual input.
data-2” address shown in the following table by manual input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camera may
not operate.
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of D Page data
1)
1)
Select page: 2, address: 00, and set data: 29.
2)
Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
PAUSE button of the adjustment remote commander.
3. D Page Table
Note1:
Fixed data-1: Initialized data. (Refer to “1. Initializing the D Page
Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D Page
Data”.)
Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of D Page
Data”.)
5-8
D4
D5
D6
D7
D8
D9 to DC
DD
DE to FF
BE
C8
7C
80
74
88
Contrast adj. (LCD)
D range adj. (LCD)
V-COM level adj. (LCD)
VCO adj. (LCD) (NTSC)
V-COM adj. (LCD)
Fixed data-1 (Initialized data)
VCO adj. (LCD) (PAL)
Fixed data-1 (Initialized data)
Address
Remark
Initial value
Table. 5-1-2.
1-2-2.
Initializing the B, E, F, 7 Page Data
1. Initializing the B, E, F, 7 Page Data
Note1:
If “Initializing the B, E, F, 7 Page Data” is performed, all data of
the B page, E page, F page and 7 page will be initialized. (It is
impossible to initialize a single page.)
the B page, E page, F page and 7 page will be initialized. (It is
impossible to initialize a single page.)
Note2:
If the B, E, F, 7 Page data has been initialized, “Modification of B,
E, F, 7 Page Data” and following adjustments need to be performed
again.
1) Video system adjustments
2) Camera system adjustments
E, F, 7 Page Data” and following adjustments need to be performed
again.
1) Video system adjustments
2) Camera system adjustments
Adjusting page
F
Adjusting Address
10 to FF
Adjusting page
7
Adjusting Address
00 to FF
Adjusting page
E
Adjusting Address
00 to FF
Adjusting page
B
Adjusting Address
00 to FF
Initializing Method:
1)
1)
Select page: 0, address: 01, and set data: 01.
2)
Select page: 6, address: 03, and set data: 01.
3)
Select page: 6, address: 00, and set data: 2D.
4)
Select page: 6, address: 01, set data: 2D, and press the PAUSE
button.
button.
5)
Select page: 6, address: 02, and check that the data changes to
“01”.
“01”.
6)
Perform “Modification of B, E, F, 7 Page Data”.
2. Modification of B, E, F, 7 Page Data
If the B, E, F, 7 Page data has been initialized, change the data of
the “Fixed data-2” address shown in the following tables by manual
input.
the “Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camera may
not operate.
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of B, E, F, 7 Page data
1)
1)
Select page: 2, address: 00, and set data: 29.
2)
Select page: 2, address: 01, and set data: 29, and press the
PAUSE button of the adjustment remote commander.
PAUSE button of the adjustment remote commander.
5-9
4F to 58
59
5A
5B
5C
5D
5E
5F
60 to 63
64
65
66
67 to 68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81 to 9F
A0
A1
A2
A3
A4 to FF
00
14
63
83
03
E9
10
61
61
01
A3
B4
0B
C2
09
42
06
C2
05
C2
04
C2
33
33
33
33
33
33
33
33
33
33
00
00
00
00
00
Fixed data-1 (Initialized data)
AWB standard data input
Mechanical shutter adj.
Fixed data-1 (Initialized data)
Color reproduction adj.
Fixed data-1 (Initialized data)
Strobe white balance adj.
Video output level adj.
Fixed data-1 (Initialized data)
Strobe white balance adj.
Mechanical shutter adj.
Auto white balance adj.
Fixed data-1 (Initialized data)
Mixed color cancel adj.
Fixed data-1 (Initialized data)
00 to 0F
10 to 13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30 to 33
34
35
36 to 39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49 to 4C
4D
4E
10
00
10
01
11
00
00
00
00
00
00
00
20
20
20
04
0A
00
85
94
47
41
3D
3D
80
93
15
7C
2F
37
40
D0
B5
43
03
E9
63
83
D5
FE
73
45
27
77
Fixed data-1 (Initialized data)
Flange back adj.
Light level Adj.
Fixed data-1 (Initialized data)
Light level Adj.
F No. standard data input
Fixed data-1 (Initialized data)
Hall adj.
Fixed data-1 (Initialized data)
Hall adj.
Fixed data-1 (Initialized data)
AWB standard data input
Fixed data-1 (Initialized data)
Auto white balance adj.
Color reproduction adj.
Fixed data-1 (Initialized data)
Strobe white balance adj.
Address
Remark
Initial value
Address
Remark
Initial value
3. F Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7
Page Data”.)
Table. 5-1-3.
Click on the first or last page to see other DSC-F55V (serv.man2) service manuals if exist.