Sony XSP-N1BT Service Manual ▷ View online
XSP-N1BT
25
SECTION 3
DISASSEMBLY
•
This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1), PANEL FRONT BLOCK
3-2. MINI FUSE (BLADE TYPE) (10A/32V) (FU1), PANEL FRONT BLOCK
(Page
(Page
25)
3-3. SHAFT GEAR BLOCK
(Page
(Page
26)
3-4. GEAR, SHAFT GEAR
(Page
(Page
26)
3-5. LCD
BOARD
(Page
27)
3-11. SLIDER L/R,
ADJUSTER
ADJUSTER
PLATE
ASSY
(Page
30)
3-8. COVER BUTTON BLOCK
(Page
(Page
29)
3-9. KEY BOARD, COVER BUTTON SV ASSY (CB1)
(Page
(Page
29)
3-7. CONNECTOR
ASSY
(CN900)
(Page
28)
3-6. LEVER DETECT P
(Page
(Page
28)
3-15. MAIN BOARD
(Page
(Page
33)
3-16. ANTENNA BT (BT1)
(Page
(Page
33)
3-12. CHASSIS TOP BLOCK
(Page
(Page
31)
3-13.
SLIDER POPUP
(Page
31)
3-14. CD MECHANISM DECK
(MG-101CF-188)
(Page
(MG-101CF-188)
(Page
32)
3-10. COVER SLIDER L/R
(Page
(Page
30)
SET
3 two claws
2 screw
(PTT2.6
(PTT2.6
u 6)
1 mini fuse (blade type) (10 A/32 V)
(FU1)
(FU1)
2 screw
(PTT2.6
(PTT2.6
u 6)
3 two claws
3 two claws
4 panel front block
XSP-N1BT
26
3-3. SHAFT GEAR BLOCK
3-4. GEAR, SHAFT GEAR
– Panel front block rear bottom view –
– Panel front block front bottom view –
1 Push the RELEASE button.
4 shaft gear block
3 shaft
3 shaft
2 Move the adjuster plate in
the direction of the arrow.
adjuster plate
Note: When installing the shaft gear block, move
the adjuster plate to the top position.
1 gear
1 gear
2 shaft gear
$SSOLFDWLRQSRVLWLRQRIJUHDVH
Note 2: When replacing the gear, it is
necessary to spread the grease.
Spread the grease referring to
the figure below.
FLOIL SGP-110F [black]
FLOIL SGP-110F [black]
$SSOLFDWLRQSRVLWLRQRIJUHDVH
Note 2: When replacing the gear, it is
necessary to spread the grease.
Spread the grease referring to
the figure below.
Note 1: When installing the gear, aline the form of the
hole of the gear and the form of the shaft gear.
shaft gear
gear
XSP-N1BT
27
3-5. LCD BOARD
4 two screws
(B P-TITE M2)
4 two screws
(B P-TITE M2)
1 filament tape
(sub
material)
1 filament tape
(sub
material)
LCD board
2 Remove the solder.
[red]
[red]
2 Remove the solder.
[black]
[black]
Insert two wires in the
hole of the LCD board.
hole of the LCD board.
7 button eject
3 flexible flat cable (10 core)
(CN903)
flexible flat cable
(CN903)
(CN903)
6 cover cable
8 LCD board
LCD board
20 mm
– Panel front block rear bottom view –
Wire setting
Note 1: Wires must not overlap
on the lever detect P.
Note 3: The filament tape must
not overlap on the hole
of LCD board.
Note 2: Bend wires at 90 degrees.
Note 4: This portion must not be
fixed on the filament tape.
filament tape (sub material)
Note 5: When installing the flexible flat cable, ensure that the
colored line is not slanted after insertion.
colored line
Insert is straight to the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert is incline.
flexible flat
cable
cable
connector
NG
5 Remove the LCD board in
the direction of the arrow.
filament tape
(sub material)
(sub material)
Flexible flat cable setting
XSP-N1BT
28
3-6. LEVER DETECT P
3-7. CONNECTOR ASSY (CN900)
3 spring detect P
4 lever detect P
1 shaft
1 shaft
lever detect P
ditch
2 Remove the lever detect P block
in the direction of the arrow.
– Panel front block rear top view –
Spring detect P setting
spring detect P
3 Remove the connector assy (CN900)
in the direction of an arrow.
4 Draw out two wires.
1 two claws
2 two claws
5 connector assy
(CN900)
(CN900)
– Panel front block rear bottom view –
Click on the first or last page to see other XSP-N1BT service manuals if exist.