DOWNLOAD Sony MEX-N6000BD / MEX-N6001BD Service Manual ↓ Size: 5.88 MB | Pages: 52 in PDF or view online for FREE

MEX-N6000BD

Setting method:
1.  In the state of source off (the clock is displayed on the liquid 

crystal display), enter the test mode by pressing the buttons in 
order of the [  4] t [MIC 5] t [V

 

ALBUM 1] (press only 

the [V

 

ALBUM 1] button for two seconds).

2.  It is set to the test mode, and all segments of the liquid crystal 

display light.

Releasing method:
Press the [

 

OFF SRC] button for 1 second.

MICROPHONE  AUDIO  LOOPBACK
To confi rm the state of the external microphone used when a 
handsfree function is used, the microphone audio is output from 
the speaker.
The breakdown judgment of the microphone can be done without 
connecting H/F with the cellular phone.

Procedure:
1.  Enter the test mode.
2. Press the [

 

OFF SRC] button to select the Bluetooth Phone 

function.

3.  On/off of the microphone audio loopback function changes 

whenever the [ALBUM v

 

2] button is pressed (“ ” is dis-

played on the liquid crystal display).

ON

Lit

OFF

None

1 filament tape

2 lead wire with connector
 (CN1002)

3 screw (T)

4 antenna BT
 (BT1)

6 ground point screw
 (PTT2.6 

u 6)

2 ground sheet (TU)

6 ground point screw
 (PTT2.6 

u 6)

1 Remove the solder.

9 MAIN board block

8 Remove the
 

5 two screws
 (PTT2.6 

u 8)

7 claw

3 filament tape

7 claw

4 lead wire with connector
 (CN1002)

Note: When the complete MAIN board is replaced, it is necessary to 

replace knob (VOL) (SV) assy simultaneously. Also, the destina-
tion setting, Bluetooth operation check and Bluetooth informa-
tion writing are necessary. Refer to “DESTINATION SETTING 
METHOD” on page 4, “BLUETOOTH FUNCTION CHECK-
ING METHOD USING A CELLULAR PHONE” on page 7 and 
“BLUETOOTH INFORMATION WRITING METHOD” on 
page 8.

MEX-N6000BD/N6001BD

CD MECHANISM

DECK BLOCK

(MG-101CF-188)

A

C

KEY BOARD (1/3)

D+
D–

B

F

E

PD

LD

1/2VCC

FOCUS

TRACK

SL

SP

X501

48MHz

X502

13.333MHz

X503

32.768kHz

X701

16.9344MHz

AUTOMATIC

POWER CONTROL

Q701

DRV_ON

LOAD

EJECT

L_SW

D_SW

IN_SW

SELF

25

PCM2_IN

26

PCM2_OUT

39 RF

13

UART_TX

14

UART_RX

23

PCM_CLK

24

PCM2_SYNC

12

RESET

IC1002

BT MODULE

SERIAL FLASH

IC502

I2C0_SCL

I2C0_SDA

EEPROM

IC1009

R-CH

R-CH

: USB

: Bluetooth

: CD PLAY

SIGNAL PATH

: AUDIO

R-ch is omitted due to same as L-ch.

RL

FL

FL, RL, SUB

SUB

I2C0_SCL

I2C0_SDA

AU_IN_RCH

AU_IN_LCH

AU_IN_LCH,

AU_IN_RCH

D501

PATTERN

ANTENNA

BT1

BT ANTENNA

MEX-N6000BD/N6001BD

6

8

CN301 (1/2)

POWER AMP

IC301

FL+

FL–

R-CH

J1001

115 DAB_PORn

J001

(ANTENNA IN)

(DAB ANTENNA)

TU01

TUX-DAB02 (N6000BD)
TUX-DAB03 (N6001BD)

(TUNER UNIT)

RF_ANT_IN

AUDIO_OUT_L

AUDIO_OUT_R

SDA

SCL

POWER_ON

R-CH

HA_SDA

HA_SCL

RSTN

MUTING

Q406

MUTING

Q408

MUTING

CONTROL

Q401, 402, 808

R-CH

5

7

FR+

FR–

2

4

RL+

RL–

R-CH

1

3

RR+

RR–

R-CH

J401

R-CH

R-CH

R

FRONT

AUDIO OUT

L

R

REAR

L

MUTING

Q404

SUB

INPUT SELECTOR, ELECTRICAL VOLUME

IC402

SYSTEM CONTROLLER

IC503 (2/3)

KEY BOARD (2/3)

AUX_L

AUX_R

AUX_GND

RL

FL

FL, RL, SUB

SUB

MUTING

Q407

: AUX

: TUNER

SIGNAL PATH

: AUDIO

R-ch is omitted due to same as L-ch.

: MIC

AU_IN_RCH

AU_IN_LCH

AU_IN_LCH,

I2C0_SCL

I2C0_SDA

I2C0_SDA,

MIC

MEX-N6000BD/N6001BD

REGULATOR

IC803

CN301 (2/2)

VCC

15

9

AMP_REM

13

ACC

SYSTEM CONTROLLER

IC503 (3/3)

J801

(REMOTE IN)

132 RE_IN1
131 RE_IN0

KEY BOARD (3/3)

LCD_DATA

LCD_CLK

LCD_CE

SIRC

KEY_1
KEY_0

RE_1
RE_0

PANEL_SW

BT_3.3V

FP_B+

DR_6V

DR_3.3V

TU_6V

118

112

VBUS_5V

TU_12V

TU_3.3V

AU_8.5V

VCC

D818

D817

BATTERY

CHECK

Q813

ACCESSORY

CHECK

Q806

11

ILL

DIMMER
DETECT

Q807

BACK UP

VOLTAGE DETECT

Q812, 814

REGULATOR

Q805

D814

D502

B+ SWITCH

Q803

POWER

CONTROL

Q801, 802

D802

D816

DR_1.5V

I2C0_SCL

I2C0_SDA

I2C0_SDA,

I2C0_SCL

BU_1.5V

BU_3.3V

P-COM_1.2V

RESET

117

REGULATOR

Q804