Sony MEX-DV900 / MEX-DV90EE Service Manual ▷ View online
MEX-DV90EE/DV900
13
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SET
3-2. SUB PANEL COMPLETE ASSY
(Page
(Page
13)
3-3. DVD MECHANISM DECK BLOCK
(Page
(Page
14)
3-4. DC FAN (25X25) (M901),
MAIN
MAIN
BOARD
(Page
14)
3-5. SENSOR BOARD,
CHASSIS (T612Z) SUB ASSY
(Page
15)
3-7. SERVO BOARD
(Page
(Page
16)
3-6. CHASSIS (OP, Z) COMPLETE ASSY
(Page
(Page
15)
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
Note: Illustration of disassembly is omitted.
Note: Follow the disassembly procedure in the numerical order given.
3-2. SUB PANEL COMPLETE ASSY
screw
(PTT2.6
× 6)
two screws
(PTT2.6
× 6)
two bosses
three claws
two bosses
cover block
two claws
two claws
sub panel complete assy
MEX-DV90EE/DV900
14
3-3. DVD MECHANISM DECK BLOCK
connector
(CN3)
screw
(PTT2.6
× 6)
two screws
(PTT2.6
× 5)
two screws
(P1.7
× 2.2)
shield (612Z)
bracket (CD)
dust protection sheet
R DVD mechanism deck block
laser caution label
screw
(PTT2.6
× 6)
Lift up the DVD mechanism deck
(MG-612L-187).
(DV90EE/DV900: AEP, UK)
3-4. DC FAN (25X25) (M901), MAIN BOARD
three screws
(BTT2.6
× 5)
RT MAIN board
fuse (blade type)
(auto fuse) (10A/32V)
(FU801)
chassis
two screws
(PS2.6
× 14)
Lift up the lead pin to upper right.
screw
(PTT2.6
× 8)
two screws
(PTT2.6
× 8)
connection cord for automobile
(rear
audio
out)
RB DC fan (25 × 25)
(M901)
R connector
(CN901)
connector
(CN301)
Note: When the DC fan and MAIN board
are mounted, lock with connection
cord for automobile and DC fan wire
by push lead pin.
MEX-DV90EE/DV900
15
3-5. SENSOR BOARD, CHASSIS (T612Z) SUB ASSY
two screws
(P1.7
× 2.2)
chassis (T612Z) sub assy
two screws
(P1.7
× 2.2)
claw
claw
Remove the three solders.
SENSOR borad
3-6. CHASSIS (OP, Z) COMPLETE ASSY
"
OP flexible board
(CN2)
two coil springs (damper)
chassis (OP, Z) complete assy
compression spring (damper, Z)
flexible board
(CN1)
tension spring (KF)
Turn the gear (RA1) fully in the
direction of arrow ".
MEX-DV90EE/DV900
16
3-7. SERVO BOARD
– DVD mechanism deck block (Bottom view) –
Remove the three solders.
SERVO board
Remove the two solders.
four screws
(M1.7
× 2.5)
OP flexible board
(CN2)
flexible board
(CN1)
spacer (PWB7)
Note: When disconnecting the OP flexible board from of the connector.
Be sure to refer to “NOTE FOR FLEXIBLE BOARD OF THE
OPTICAL PICK-UP” of the servicing notes (See page 5).
Click on the first or last page to see other MEX-DV900 / MEX-DV90EE service manuals if exist.