DOWNLOAD Sony CDX-V60 Service Manual ↓ Size: 1.4 MB | Pages: 51 in PDF or view online for FREE

– 13 –

4

spindle motor ass’y
(M302)

2

chuck plate

3

two screws (P1.7 

×

 3.5)

1

retainer (C thrust)

3

retainer (C) ass’y

1

Putting a screw about
M3 size in the gap
marks removal easier.

7

shaft (T release)

6

arm (T driving gear)
ass’y

5

arm (D hold)

4

spring (D hold)

3

retainer (P) ass’y

2

three screws (P2 

×

 2.5)

– 14 –

1

5

gear
(FL driving A)

4

lever (T push)

2

3

lever (disc retainer)

2

cam gear (C)
ass’y

3

arm (chucking)
ass’y

3

retainer (disc)
ass’y

cam gear (C)

cam gear (C)

lever (disc retainer)

lever (T push)

Good

NG

roller

roller

parallel

slot

round
hole

outsert (OP) ass’y

1

lever (FLP) ass’y

4

reel stopper

3

cam gear (CTP)

2

arm (C/T selection)
ass’y

gear (SDP)

cam gear (CTP)

gear (SDP)

notch tooth
(1 peak)

pin

Follow the assembly procedure in the numerical order given.

1 Install the cam gear (C) ass’y.

(The cam gear (C) roller must securely enter the irregularly
shaped hole in the lever (disc retainer).)

2 Turn the cam gear (C) ass’y all the way clockwise.
3 Check that the lever (disc retainer) and arm (chucking) ass’y

each move in the direction of the arrow. (with the retainer (disc)
ass’y up in the direction of the arrow.)

4 Slide the lever (T push) all the way in the direction of the ar-

row.

5 Install the gear (FL drive A) so that the extension line between

the gear (FL driving A) slot 

 and round hole 

® is parallel

with the level (T push).
Rotate the gear (FL driving A) and check that it meshes.

1 Slide the lever (FLP) ass’y all the way in the arrow direction.
2 Move the arm (C/T selection) ass’y in the arrow direction.
3 Install the cam gear (CTP) with its notch tooth (1 peak) sec-

tion and the gear (SDP) meshing.
Rotate the cam gear (CTP) 1/4 turn to check that it operates
without catching or other obstruction.

4 Install the reel stopper.

– 15 –

stop ring (2.0)

reel stopper

arm (trigger E)

gear (EL 2)

outsert (OPT)
ass’y

chassis (FA)
ass’y

rectangular
hole

chassis (FA)
ass’y

gear (EL 2)

chassis
(FA) ass’y

outser (OPT)
ass’y

rectangular
hole

second
hole

first hole

gear (EL 1)

gear (EL 1)

gear (EL 1)

arm (trigger E)

arm (trigger E)

arm (trigger E)

gear (EL 1)

good

NG

A

good

NG

chassis (FA) ass’y

1. Remove the arm (trigger E) and gear (EL1).
2. Turning the two gears (EL2) changes the elevator height.Turn

the two gear (EL2) together and align the center of the rectan-
gular hole of the chassis (FA) ass’y with the outsert (OPT)
ass’y. (Elevator Address 1 adjustment)
* The left side gear (EL2) is harder to turn than the right side
gear (EL2) , so use some strength tuning it.

3. Without moving the two gear (EL2) , install the gear (EL1) so

that the second hole on the gear (EL1) is aligned with the hole
in the chassis (FA) ass’y.

4. Install the arm (trigger E) so that the arm (trigger E) A section

is directly above the hole in the gear (EL1).

– 16 –

+
–

+
–

digital voltmeter

DC power supply

TP

(EHS)

TP

(VREF)

TP

(GND)

RV601

adjustment screw

servo board

retainer plate

bend

slider

mechanism deck rear view

1. When the elevator height is adjusted as part of any repairs, the

linear position sensor (RV601) must be adjusted.
This adjustment is for absorbing the variation in the perfor-
mance of the RV601 parts and is not a mechanical deck
adjustment.Therefore, this adjustment is only carried out when
the mechanical deck elevator height adjustment (Address 1
adjustment) is made.

2. Never supply power to the set main unit during this

adjustment.(Have the bus cable disconnected.)

Adjustment method:
1. Extend the plate holding down the RV601 slider with radial

pliers to free the slider.

2. Connect the TP (VREF) on the servo board to a dc power sup-

ply.

3. Connect the TP (EHS) on the servo board to a digital voltme-

ter.

4. Supply 5.00 ± 0.01 V power from the dc power supply to the

TP (VREF).

5. Turn the adjustment screw so that the digital voltmeter reads

4.03 ± 0.02 V.

6. After the adjustment,disconnect the dc power supply and the

digital voltmeter.

7. Apply the power supply to the set main unit, insert the maga-

zine, operate, and check that there is no address deviation.

8. Bend the retainer plate back the way it was originally.
9. Apply suitable locking compound to the adjustment screw.

* After adjusting the linear position sensor (RV601) , put in

the magazine and operate. If address deviation is found, re-
check the elevator height adjustment (Elevator Address 1 ad-
justment).
The following causes are possible.
Examples:
• The mechanical deck gear (TDFP) and magazine gear teeth

are not meshing.

• During ejection, the gear (EL1) was not in the prescribed

position.

• After magazine ejection was carried out five times, the

magazine lock was unlocked.

[SERVO BOARD] (Conductor Side)