Sony ZS-PS30CP Service Manual ▷ View online
ZS-PS30CP
9
2-6. MAIN BOARD BLOCK
Note 1: Before disconnecting the fl exible fl at cable (16 core) of optical pick-up block, solder the short-land.
6
Solder the short-land.
Note 2: When assembling the MAIN
board block, remove the
solder of short-land after
connecting the flexible flat
cable (16 core).
cabinet (upper)
7
flexible flat cable (16 core)
8
flexible flat cable (6 core)
9
MAIN board block
MAIN board
front side
tape
3
connector
(S801)
4
two tapping screws
(BV
B2.6)
4
four tapping screws
(BV
B2.6)
4
tapping screw
(BV
B2.6)
1
tapping screw
(PWH
B2.6)
2
Remove ferrite core
from
rib.
ferrite core
Wire is below a screw hole. Wire is above a screw hole.
ferrite core
5
Remove the MAIN board block
in the direction of an arrow.
– Cabinet (upper) block bottom side view –
OK
NG
tape
:ire settinJ
Note 3: When installing the flexible
flat cable, ensure the coloured
line.
No slanting after insertion.
coloured line
coloured line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
ZS-PS30CP
10
2-7. MAIN BOARD
1
ferrite core (FC1)
3
two cabinet upper
cushions 10 X 7 X0.3
3
two cabinet upper
cushions 10 X 7 X0.3
2
flexible flat cable (16 core) (FFC801)
(CN810)
flexible flat cable
(16 core)
(FFC801)
(16 core)
(FFC801)
)HUULWHFRUH)&VHWWLQJ
WireVeWWiQJ
ferrite core (FC1)
tape
Be based on
a black line.
a black line.
Roll the wire three times.
from MAIN board
to POWER board
5
two tapping screws
(BV
B2.6)
qd
holder (LCD) block
qs
screw
qs
screw
6
two bosses (PC board)
qa
liquid crystal display
panel (LCD401)
0
Remove adhesive
sheet (panel dock).
9
Remove thirty
three
solders.
7
Remove two solders.
qh
Remove two solders.
qk
MAIN board
MAIN board
qj
heat sink (AMP)
qf
Remove three solders.
qg
shield plate
C703
tape
tape
C919
CN808
C808
X802
C821
Q905
8
led (D401)
4
cushion
(CAB
rear)
coloured line
coloured line
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
flexible flat
cable
cable
connector
connector
OK
NG
Note: When installing the flexible flat
cable, ensure the coloured line.
No slanting after insertion.
ZS-PS30CP
11
2-9. OPTICAL PICK-UP (DA11MMVGP) (OP1)
2-8. CD BLOCK ASSY
2
CD block assy
– Cabinet (upper) block bottom side view –
1
two tapping screws
(PWH
B2.6)
1
two tapping screws
(PWH
B2.6)
3
claw
2
vibration proof rubber
(green)
1
vibration proof rubber
(red)
3
claw
3
claw
1
vibration proof rubber
(red)
7
optical pick-up (DA11MMVGP)
(OP1)
optical pick-up
(DA11MMVGP)
(OP1)
(DA11MMVGP)
(OP1)
6
MOTOR board
4
CD cover
Note: Three claws might be fixed by bond.
When installing the CD cover, please
fix three claws using the following bond.
Part No.
Description
7-432-912-48 SONY BOND SC608LV (180 ml)
2
vibration proof rubber
(green)
vibration proof rubber
Upper side
Lower side
5
Remove four solders.
9LEUDWLRQSURRIUXEEHUVHWWLQJ
3
claw
ZS-PS30CP
12
1
Open the CD lid.
5
CD spring
CD spring
4
shaft
3
claw
&'VSULQJVHWWLQJ
&'VSULQJVHWWLQJ
CD lid
2
Remove the spring
(CD) from the ditch
of CD lid.
ditch
CD spring
CD lid
OK
NG
1 Insert the CD spring.
4 Insert the CD spring
to the ditch of CD lid.
2 Insert in the shaft.
$VVHPEOLQJSURFHGXUHRIWKH&'VSULQJ
3 Hook CD spring on claw.
–
&DELQHWXSSHUEORFN
–
ULJKWVLGHYLHZ
2-11. JACK (IN) BOARD
2-10. CD SPRING
1
tapping screw
(BV
B2.6)
2
JACK (IN) board
– Cabinet (front) block rear right side view –
Click on the first or last page to see other ZS-PS30CP service manuals if exist.