Sony ZS-PS30CP Service Manual ▷ View online
ZS-PS30CP
13
2-13. BUTTON (VOL) BOARD
2-12. SPEAKER (7.7 cm) (L-CH) (SP101)
4
speaker (7.7 cm)
(L-CH)
(SP101)
2
Remove the speaker (7.7 cm) (L-CH)
(SP101) in the direction of an arrow.
– Cabinet (front) block rear right side view –
1
four tapping screws
(BV
B2.6)
red (
+)
white (
−)
3
Remove solder
from
the
“
−” terminal.
3
Remove solder
from
the
“
+” terminal.
:ire setting
speaker terminal
Twist a wire around
a speaker terminal hole.
a speaker terminal hole.
wire
Speaker (7.7 cm) (L-CH) (SP101) setting
Install the speaker
(7.7 cm) (L-CH)
(SP101) in inside
two ribs.
(7.7 cm) (L-CH)
(SP101) in inside
two ribs.
1
two tapping screws
(BV
B2.6)
2
RETAINER board
4
connector
(CN402)
3
Remove the BUTTON (VOL) board
block in the direction of an arrow.
7
BUTTON (VOL) board
5
button (volume)
6
two sheets (1)
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
– Cabinet (front) block rear left side view –
ZS-PS30CP
14
2-14. USB JACK BOARD
:LUHVHWWLQJ
3
tapping screw
(BV
B2.6)
3
tapping screw
(BV
B2.6)
1
tapping screw
(PWH
B2.6)
2
Remove ferrite core from rib.
5
ferrite core
(FC2)
6
Remove four
solders.
7
shield plate
(USB)
4
Remove the USB JACK board block
in the direction of an arrow.
8
USB JACK board
)HUULWHFRUH)&VHWWLQJ
ferrite core
(FC2)
(FC2)
Roll the wire twice.
tape
Be based on a red line.
USB JACK board
USB JACK board
BUTTON (VOL) board
speaker (7.7 cm) (L-CH) (SP101)
speaker (7.7 cm) (R-CH) (SP201)
tape
tape
tape
–&DELQHWIURQWEORFNUHDUOHIWVLGHYLHZ–
ZS-PS30CP
15
2-16. TELESCOPIC ANTENNA (ANT1), ANTENNA SPRING
2-15. SPEAKER (7.7 cm) (R-CH) (SP201)
4
speaker (7.7 cm)
(R-CH)
(SP201)
1
four tapping screws
(BV
B2.6)
2
Remove the speaker (7.7 cm) (R-CH)
(SP201) in the direction of an arrow.
– Cabinet (front) block rear left side view –
red (
+)
white (
−)
3
Remove solder
from
the
“
−” terminal.
3
Remove solder
from
the
“
+” terminal.
:ire settinJ
Speaker (7.7 cm) (R-CH) (SP201) settinJ
speaker terminal
Twist a wire around
a speaker terminal hole.
a speaker terminal hole.
wire
Install the speaker (7.7 cm) (R-CH)
(SP201) in inside two ribs.
(SP201) in inside two ribs.
5
antenna spring
antenna spring
2
telescopic antenna
(ANT1)
1
screw
(P
M3)
4
claw
$QWHQQDVSULQJVHWWLQJ
3
tapping screw
(BV
B2.6)
1
2
4
5
6
7
3
Note: Attach to numerical order.
ZS-PS30CP
16
2-17. POWER BOARD
1
connector
(CN903)
7
power transformer (T901)
8
POWER board
:LUHVHWWLQJ
2
two tapping screws
(BV
B2.6)
2
two tapping screws
(BV
B2.6)
2
tapping screw
(BV
B2.6)
4
tapping screw
(BV
B2.6)
3
Remove the POWER board block
in the direction of an arrow.
5
holder (inlet)
ditch of rib
Twist a wire 3 to 4 times.
Note: Arranging so that a wire may not exceed this line.
tape
tape
tape
6
Remove five solders.
white
red
Insert is straight
to the interior.
to the interior.
connector
connector
OK
Insert is shallow
Insert is incline
connector
connector
connector
connector
NG
NG
Note: When you install the connector, please install themcorrectly.
There is a possibility that this machine damages when not
correctly installing it.
–&DELQHWUHDUEORFNIURQWOHIWVLGHYLHZ–
Click on the first or last page to see other ZS-PS30CP service manuals if exist.