Sony ZS-BTY50 / ZS-BTY52 / ZS-BTY55 Service Manual ▷ View online
ZS-BTY50/BTY52/BTY55
29
2-33. JOINT (Lch)
150 ± 5 mm
binding band (taiton)
Note 1: In reassembling, use new binding
band (taiton) to fasten the clamp
same as before.
:LUHVHWWLQJ
The knot at a tip is inside.
The knot at a tip is outside.
Wire is outside.
Note 2: Check the position of
the binding band (taiton).
–%RWWRPVLGHYLHZ–
–%RWWRPVLGHYLHZ–
–%RWWRPVLGHYLHZ–
OK
NG
1 Cut the binding band (taiton).
2 two tapping screws
(BV
B2.6)
3 joint (Lch)
2 two tapping screws
(BV
B2.6)
2 two tapping screws
(BV
B2.6)
–5HDUVLGHYLHZ–
tape (sub material)
ZS-BTY50/BTY52/BTY55
30
2-34. LOUDSPEAKER (10.2 cm) (Lch) (SP1)
2 four tapping screws
(BV
B3)
3 Remove the loudspeaker (10.2 cm)
block in the direction of an arrow.
5 loudspeaker (10.2 cm) (Lch)
(SP1)
[black]
[white]
“
−” terminal
“
+” terminal
1 Remove two solders.
4 cushion (A wire)
– Rear side view –
6SHDNHUZLUHVHWWLQJ
Note: When installing the sloudspeaker
(10.2 cm) (Lch) (SP1), check that
terminal position is bottom side.
2-35. LIGHT GUIDE PLATE BLOCK
6SHDNHUZLUHVHWWLQJ
1
light guide plate block
2
sheet
(light
interception)
Note: When installing the sheet (light interception), align bosses
and libs of cabinet (front) with holes sheet (light interception).
5('02'(/
–5HDUVLGHYLHZ–
ZS-BTY50/BTY52/BTY55
31
2-36. LED BOARD
5 Remove the LED board
in the direction of an arrow.
cushion
cushion
7 LED board
6 connector
(CN602)
2 tape
(sub
material)
150 ± 5 mm
(RED MODEL)
(RED MODEL)
1 Cut the binding band (taiton).
binding band (taiton)
3 two sheets
(PWB
LCD)
4 two tapping screws
(BV
B2.6)
sheet (PWB LCD)
LED board
Note 1: In reassembling, use new binding
band (taiton) to fasten the clamp
same as before.
Note 2: Check that the outside of
LED board is hidden.
Note 3: Sheet (PWB LCD) must
not cover screw hole.
guide line
guide line
6heet (PWB LCD) setting
NG
LED board
Note 4: When installing the LED board, check
that sheet (light interception) is outside.
LED board
loudspeaker (10.2 cm) (Lch)
(SP1)
(SP1)
WiUe setting
WiUe setting
– ReDU siGe YieZ –
The knot at a tip is inside.
The knot at a tip is outside.
Wire is outside.
Note 5: Check the position of
the binding band (taiton).
– BRttRP siGe YieZ –
– BRttRP siGe YieZ –
– BRttRP siGe YieZ –
OK
NG
tape (sub material)
ZS-BTY50/BTY52/BTY55
32
2-37. NFC TAG (RC-S710)
1)&WDJ5&6DQGZLUHVHWWLQJ
–5HDUVLGHYLHZ–
NFC tag (RC-S710)
[white]
guide line
[black]
2
adhesive sheet (NFC)
3 NFC tag (RC-S710)
Note
2: When replacing NFC tag, please
exchange Bluetooth module
simultaneously.
1 Remove the NFC tag block
in the direction of an arrow.
Note
1: NFC tag is being fixed
in adhesive sheet. When
removing, be careful
not to damage NFC tag.
Click on the first or last page to see other ZS-BTY50 / ZS-BTY52 / ZS-BTY55 service manuals if exist.