Sony STR-DN1060 / STR-DN860 Service Manual ▷ View online
STR-DN860/DN1060
17
2-10. BACK PANEL SECTION (DN1060)
• Abbreviation
AUS :
AUS :
Australian
model
CND : Canadian model
SP
SP
: Singapore model
1
CNP901
(3P)
2
CN1905 (4P)
3
CN1907 (2P)
4
seven screws
(+BVTP
3
u 8)
4
eight screws
(+BVTP
3
u 8)
5
four screws (+BVTP 3
u 8)
(US,
CND)
four screws (BV/RING)
(AEP, UK, SP, AUS)
6
back panel section
cushion (R)
DCDC board
:LUHVHWWLQJ
clamp,
sleeve ferrite
sleeve ferrite
Ver. 1.1
STR-DN860/DN1060
18
7
two screws
(+BVTP
3
u 8)
7
two screws
(+BVTP
3
u 8)
9
MAIN BOARD
section
8
one screw
(+BVTP
3
u 8)
2
four screws
(+BVTP
3
u 8)
3
STANDBY board
1
CNP902 (4P)
5
CNP920 (5P)
6
CNP930 (5P)
4
Wire is removed
from the pin, lead.
:LUHVHWWLQJ
pin, lead
MAIN board
rear side
2-11. STANDBY BOARD, MAIN BOARD SECTION
STR-DN860/DN1060
19
2-12. MAIN BOARD
Note : This illustration sees the MAIN board from back side.
9
heat sink section
qa
two screws
(+BVTP
3
u 8)
qs
MAIN board
0
Remove the
forty-two
solders.
1
one screw
(+BVTP
3
u 8)
2
INSULATION board
4
USB INSULATION
board
3
one screw
(+BVTP
3
u 8)
7
one screw
(+BVTP
3
u 8)
7
one screw
(+BVTP
3
u 8)
8
bracket, HDMI support
7
one screw
(+BVTP
3
u 8)
5
two screws
(+BVTP
3
u 8)
6
SUPPORT
board
8
bracket, support beam
8
bracket,
support
beam
(DN1060)
(DN1060)
(DN1060)
(DN1060)
(DN1060)
(DN860)
STR-DN860/DN1060
20
SECTION 3
TEST MODE
VACUUM FLUORESCENT DISPLAY TEST MODE
All fl uorescent segments are tested.
When this test is activated, all segments light on at the same time,
then each segment lights on one after another.
Procedure:
While pressing [SPEAKERS] and [DIMMER] buttons simultane-
ously, press the [
All fl uorescent segments are tested.
When this test is activated, all segments light on at the same time,
then each segment lights on one after another.
Procedure:
While pressing [SPEAKERS] and [DIMMER] buttons simultane-
ously, press the [
?
/
1
] button to turn on the main power.
1. ALL segments light on.
HDMI ARC PARTY S.OPTIMIZER
D.C.A.C.
PLII x z NEO:6 X D.R.C. D.L.L.
EQ MEM RPT
True HD DTS-HD SPA+B
ST
USB BT UPDATE A.P.M.ZONE 2 3
COAX OPT
COAX OPT
SLEEP
MHz
k Hz
dB
HDMI OUT
A + B
2. Press the [DISPLAY MODE] button to confi rm display as
below.
HDMI
PARTY
D.C.A.C.
II z
6 D.R.C.
MEM
True HD
-HD
A B ST
USB
UPDATE
ZONE 3
OPT
SLEEP
A B
MHz
Hz
3. Press the [DISPLAY MODE] button to confi rm display as
below.
ARC
S.OPTIMIZER
PL x NEO: X
D.L.L.
RPT
DTS
SP +
BT
A.P.M.
2
COAX
EQ
HDMI OUT
A
+
B
k
dB
4. Press the [DISPLAY MODE] button, all segments light off.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated.
Use this mode before returning the product to clients upon com-
pletion of repair.
Procedure:
1. While pressing [MUSIC] button, press the [
The preset sound fi eld is cleared when this mode is activated.
Use this mode before returning the product to clients upon com-
pletion of repair.
Procedure:
1. While pressing [MUSIC] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. CLEAR” appears for a moment and initial-
ization is performed.
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
Procedure:
1. While pressing [A.F.D./2CH] and [PURE DIRECT] buttons
The software version is displayed.
Procedure:
1. While pressing [A.F.D./2CH] and [PURE DIRECT] buttons
simultaneously, press the [
?
/
1
] button to turn on the main
power.
2. The message “N106 XXX” appears (DN1060).
The message “N86 XXX” appears (DN860).
XXX: Area display
Each time the [DISPLAY MODE] button is pressed,
“M29.R.XXX”, “MAIN X.XXX”, “ADV vX.XX”,
“SFLASHvX.XX”, “HDMI.TXvX.XX” and “HDMI.RXvX.
XX” appear in this order, and returns to the “N106 XXX”
(DN1060) or “N86 XXX” (DN860) display.
“M29.R.XXX”, “MAIN X.XXX”, “ADV vX.XX”,
“SFLASHvX.XX”, “HDMI.TXvX.XX” and “HDMI.RXvX.
XX” appear in this order, and returns to the “N106 XXX”
(DN1060) or “N86 XXX” (DN860) display.
X.XX: Software version
KEY CHECK MODE
Each button can be checked.
Procedure:
1. While pressing [SPEAKERS] and [PURE DIRECT] buttons
Each button can be checked.
Procedure:
1. While pressing [SPEAKERS] and [PURE DIRECT] buttons
simultaneously, press the [
?/1
] button to turn on the main
power.
2. The message “REST 12” appears.
Every pressing of any button other than the [
?/1
] counts down
the buttons.
3. The buttons which are already counted once are not counted
again.
4. When all buttons are pressed, “REST 00” appears.
SWAP ALL MODE
The signal will be swap to all channels so that all speakers will
have sound output.
Procedure:
1. While pressing [PURE DIRECT] and [MOVIE] buttons
The signal will be swap to all channels so that all speakers will
have sound output.
Procedure:
1. While pressing [PURE DIRECT] and [MOVIE] buttons
simultaneously, press the [
?
/
1
] button to turn on the main
power.
2. The message “SWAP MODE” appears.
INITIALIZE MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing [A.F.D./2CH] and [DIMMER] buttons simul-
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing [A.F.D./2CH] and [DIMMER] buttons simul-
taneously, press the [
?
/
1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are
reset to the default values.
3. When done, the message “CLEARED !” appears, the set will
power off.
(b) ALL CLEAR INITIALIZE
Procedure:
1. While pressing [A.F.D./2CH] and [DISPLAY MODE] buttons,
Procedure:
1. While pressing [A.F.D./2CH] and [DISPLAY MODE] buttons,
press the [
?
/
1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are
reset to the default values.
3. When done, the message “CLEARED !” appears, the set will
power on.
(c) USER INITIALIZE
Procedure:
1. Turn off the receiver.
2. Hold the [
Procedure:
1. Turn off the receiver.
2. Hold the [
?
/
1
] button for 5 seconds.
3. The message “CLEARING” appears on the display.
4. After few seconds, “CLEARED !” appears.
4. After few seconds, “CLEARED !” appears.
PROTECTOR AUTO OFF
To disable auto off after protector occur.
Procedure:
1. While pressing [DISPLAY MODE] and [MOVIE] buttons si-
To disable auto off after protector occur.
Procedure:
1. While pressing [DISPLAY MODE] and [MOVIE] buttons si-
multaneously, press the [
?
/
1
] button to turn on the main power.
2. “PROTEVER” appears and switch on the set.
DCAC MIC TEST MODE
To test audio output from mic input and speakers.
Procedure:
1. While pressing [MUSIC] and [DIMMER] buttons simultane-
To test audio output from mic input and speakers.
Procedure:
1. While pressing [MUSIC] and [DIMMER] buttons simultane-
ously, press the [
?
/
1
] button to turn on the main power.
2. The message “MIC” appears.
MIC: mode that output audio from mic input
Ver. 1.2
Click on the first or last page to see other STR-DN1060 / STR-DN860 service manuals if exist.