DOWNLOAD Sony STR-DA7100ES Service Manual ↓ Size: 52.09 MB | Pages: 127 in PDF or view online for FREE

21

2

two screws
(BV/ring)

1

connector
(CN5002)

3

two screws
(BV/ring)

4

DC fan block

ql

three screws
(BVTP3 

×

 8)

qk

three screws
(BVTP3 

×

 8)

qf

eight screws
(BVTP3 

×

 8)

4

wire (flat type)
(tuner)

3

connector (CN851)

6

four connectors
(CN3801, CN3803, CN3806, CN3809)

9

three connectors
(CN603, CN602, CN601)

8

two connectors
(CN606, CN604)

5

two connectors 
(CN3807, CN3808)

2

connector 
(CNP742)

1

connector 
(CN1)

7

connector 
(TP3501)

qg

screw
(BVTP3 

×

 8)

qd

two screws
(BVTP3 

×

 8)

qs

screw (BVTP3 

×

 8)

0

two screws 
(BVTP3 

×

 8)

qj

screw
(BV3 

×

 8)

qa

screw (BV3 

×

 8)

qh

six screws
(BV/ring)

w;

back panel block

22

1

connector
(CN5231)

2

connector
(CN5261)

3

connector
(CN5251)

4

connector
(CN5206)

5

connector
(CN5263)

6

connector
(CN5002)

8

connector
(CN5280)

7

connector
(CN5201)

9

connector
(CN5240)

0

SP-TERM COM board

HDMI board

qa

connector
(CN5401)

qh

two connectors
(CNR207, CNR208)

qg

MOTHER COM board

qs

Remove five solders.

qf

three screws
(BVTP3 

×

 8)

qj

CONECT board

qd

screw
(BVTP3 

×

 8)

23

All preset contents are reset to the default setting.
Procedure:
1. While pressing the 

[SURR BACK DECODING]

  and 

[PRE-

SET TUNING --]

 buttons, press the

I/1

button to turn on the

main power.

2. The message “TUNER FACTORY PRESET” appears and the

present contents are reset to the default values.

All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [INPUT MODE] and [MEMORY/ENTER] but-

tons, press the  

I/1 

 button to turn on the main power.

2. The message “MEMORY CLEARING...” appears and the

memories are reset to the default values.

3. When done, the message “MEMORY CLEARED !” appears.

Procedure:
1. While pressing the 

[2CH]

 and 

[MEMORY/ENTER]

 buttons,

press the  

I/1 

 button to turn on the main power.

2. The message “SWAP MODE !” appears.
3. Press the 

[DISPLAY]

 button.

4. The message “–34.5” appears. (Volume level is “MID”)
5. Press the 

[DISPLAY]

 button once again.

6. The message “23.0” appears. (Volume level is “MAX”)
7. Press the 

[DISPLAY]

 button once again.

8. The message “–

∞” appears. (Volume level is “MIN”)

All fluorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. While pressing the 

[DISPLAY]

 and 

[MEMORY/ENTER]

 but-

tons, press the  

I/1 

 button to turn on the main power.

2. All segments and all LEDs turn on.

Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the  

I/1 

 button to turn on the main power.

2. Turn the [INPUT SELECTOR] dial to select the “AM” .
3. Press the  

I/1 

 button to turn off the main power.

4. While pressing the [PRESET TUNING +] or [TUNING +] but-

ton, press the  

I/1 

 button to turn on the main power.

5. Either the message “AM 9K STEP” or “AM 10K STEP” ap-

pears, Select the desired step.

The preset sound field is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the 

[MUSIC]

 button, press the  

I/1 

 button to

turn on the main power.

2. The message “S. F. Initialize” appears and initialization is per-

formed.

The command mode of the remote-commander which this set re-
ceives can be changed.
Procedure:
1. While pressing the 

[2CH]

 button, press the

I/1

button to turn

on the main power.

2. Either the message “COMMAND MODE [AV1]” or “COM-

MAND MODE [AV2]” appears. Select the desired mode.

Procedure:
1. While pressing the 

[MUSIC]

 and 

[MEMORY/ENTER]

 buttons,

press the

I/1

button to turn on the main power.

2. Either the message “SF LOCK [OFF]” or “SF LOCK [ON]”

appears.

Connect the set to a unit equipped with the i.LINK terminal to
check if the communication can be made correctly. By this opera-
tion check, a loose connection of the connector or a disconnection
of the i.LINK cable can be confirmed.
Procedure:
1. Press the

I/1

button to turn on the power, and press the [I.LINK]

button to set the function to the “i.LINK” so that the “No LINK”
is displayed

2. Turn on the power of the unit equipped with the i.LINK termi-

nal.

3. Connect the set to the unit equipped with the i.LINK terminal

using the i.LINK calbe.
At this time, check that “i.LINK CONNECTING”, is displayed
on the set.

4. After the display of “i.LINK CONNECTING”, check that the

equipment information is displayed

5. Moving the i.LINK cable with the i.LINK connection main-

tained, check that the “i.LINK CONNECTING” is not dis-
played.

If nothing is displayed in step 3 and 4, or if “i.LINK CONNECT-
ING” is displayed continuously, the i.LINK cable will be discon-
nected or the connector connection will be loose.
If “i.LINK CONNECTING” is displayed in step 5 though the cable
is not removed, the i.LINK cable will be disconnected or the con-
nector connection will be loose.

24

The state that the set is used is memorized.
Procedure:
1. While pressing the 

[A.F.D]

 and 

[MEMORY/ENTER]

 buttons,

press the I

/1

button to turn on the power and “HISTORY

MODE” is displayed.

2. Press the [MAIN MENU] key of remote commander.
3. Each time the 

 ↑   ↓

  key of remote commander is pressed, the

item is switched in order as follows.

Note: The parameter is memorized when “PROTECTOR 21” is

generated, and it doesn’t update the parameter thereafter
when other protector is generated, the parameter when data
is updated every time, and protector was generated at the
end is memorized.

Items

Display

Detected protect code/channel

PRCT NO/CH: XX/XX

Number of protector is generated

PRCT COUNT: XXX

Total use time

TTL_TIME: XXXXH XXM

Sound field setting

XXXXXXXXXXXXXXXX

Input when protect is detected

INPUT: XXXXXXXXXX

Input mode setting

INMODE: XXXXXXXXXXXX

Input mode under lick state

DSEL: XXXXXXXXXXXXXXX

Stream under input

STREAM: XXXXXXX

Channel information

CONFIG:XXXXXXX

State of headphone

HEAD PHONE: XXX

Volume

VOL: XXXdB

EQ setting value

BASS:    XXXdB

TREB:    XXXdB

Lv FL/FR  XXXX/XXXX

Level collection value

Lv SL/SR  XXXX/XXXX

each channel

Lv CT/SW  XXXX/XXXX

Lv BL/BR  XXXX/XXXX

Total time of power on

TTL_P_ON: XXXXH XXM