DOWNLOAD Sony STR-DA7100ES Service Manual ↓ Size: 52.09 MB | Pages: 127 in PDF or view online for FREE

17

This remote is only for 2ND ZONE out and 
3RD ZONE out operations. You cannot 
control the main receiver directly with this 
remote.

A ?

1

Press to turn a receiver in the 
2nd (or 3rd) zone on or off.

B

Press to select the command 
mode of the remote.

C

Press one of the buttons to 
select the component you want 
to use. When you press any of 
the input buttons, the receiver 
turns on. The buttons are 
factory assigned to control Sony 
components as follows. You can 
change the button assignments 
following the steps in 
“Changing button assignments 
(RM-US106A only)”.

D

When the tuner is selected, 
press repeatedly to select a 
memory page for presetting 
radio stations or tuning to preset 
stations.

E

Press to mute the sound.

F

Press to adjust the volume level 
for 2ND ZONE or 3RD ZONE 
output.

G

Lights up when data is being 
sent.

H

Press to change the category of 
the buttons.

* The setting cannot be changed.

VIDEO 1

VCR (VTR mode 3)

VIDEO 2

VCR (VTR mode 1)

VIDEO 3

VCR (VTR mode 2)

DVD

DVD player

TV/SAT

TV tuner

TAPE

Tape deck B

MD/DAT

MD deck

SA-CD/CD Super Audio CD/CD 

player

TUNER*

Built-in tuner

SOURCE

The current input 
selected for the main 
receiver

*

The  function of these buttons switches 
automatically each time you press the input 
buttons C. The above explanation is intended to 
serve as an example only. Therefore, depending 
on the component, the above operation may not 
be possible or may operate differently than 
described.

I

The following table describes 
the function of the buttons.

J

Press repeatedly to select a 
preset station or channel. When 
using a multi-disc changer, 
press to skip a disc.

N

Starts play. (Starts play 
on the front side of the 
cassette.)

n

Starts play on the 
reverse side of the 
cassette.

X

Pauses play or 
recording, and starts 
recording when the 
component is in 
recording standby.

x

Stops play.

./>

Skips tracks.

18

 Follow the disassembly procedure in the numerical order given.

•

This set can be disassembled in the order shown below.

SET

3-2. CASE

(Page 18)

3-3. FRONT PANEL ASSY

(Page 19)

3-4. BOTTOM PLATE

(Page 20)

3-7. BACK PANEL BLOCK

(Page 21)

3-8. MOTHER COM BOARD

(Page 22)

3-5. D-AMP BOARD BLOCK

(Page 20)

3-6. DC FAN BLOCK

(Page 21)

2

2

1

two screws
(flat head)

1

two screws
(flat head)

1

two screws
(flat head)

3

case

19

3

screw
(BVTP3 

×

 8)

4

bracket (panel)

6

bracket (panel)

5

screw
(BVTP3 

×

 8)

7

screw
(BVTP3 

×

 8)

qa

screw
(BVTP3 

×

 8)

qg

front panel assy

qd

screw
(BVTP3 

×

 8)

qs

harness

HP board

qf

harness

0

connector (CN1012)

9

8

seven screws
(BV/RING)

2

connector (CN2016)

1

connector (CN2014)

20

Note: When installing the ILINK board, Please refer to the service note

“NOTE WHEN INSTALLING THE ILINK BOARD” (page10)

2

two screws
(BVTP3 

×

 8)

4

0

six screws
(BVTP3 

×

 8)

qa

bottom plate
(D71S) block

6

connector
(CN3402)

7

connector
(CN5003)

8

connector
(CN3005)

9

ILINK board assy

5

connector
(CN3003,
CN3004)

3

four screws
(BVTP3 

×

 8)

1

three screws
(BVTP3 

×

 8)

qs

six screws
(BVTP3 

×

 8)

qd

nine screws
(BVTP3 

×

 8)

qf

bottom plate (D71) block

5

screw
(BVTP3 

×

 8)

7

two screws
(BT/ring)

6

screw
(BVTP3 

×

 8)

8

D-AMP board block

3

connector (CN1408)

1

connector (CN1401)

2

connector 
(CN1409)

4

connector (CN1407)