Sony PCM-D100 Service Manual ▷ View online
PCM-D100
9
2-4. LCD ASSY (LCD1)
Insert is straight to the interior.
Insert is incline
LCD flexible
board
board
connector
connector
LCD flexible
board
board
OK
NG
Note: When installing the LCD flexible board,
check that it have inserted straight.
No slanting after insertion.
2 two stoppers
(M1.7
u 3.0)
3 two screws
4 LCD assy (LCD1)
1 LCD flexible board
(CN4205)
– Front top view –
2-5. KNOB (REC VOL) (L) BLOCK, SPACER (REC VOL) B
2 three claws
3 ornament (REC VOL)
5 knob (REC VOL) (L) block
6 spring
(knob REC L)
7 spacer
(REC VOL) B
spacer (REC VOL) B
rib
shaft
hole
1 open the
guard
(REC).
ornament (REC VOL)
five holes
0
1
2
3
4
5
6
7
8
9
10
– Front top view –
shaft
Note 1: When installing the ornament (REC VOL), align this claw
with the position of “0” mark of the knob (REC VOL) block.
Note 4: When installing the spacer (REC VOL) B,
arrange the rib outside.
Note 3: When installing the knob (REC VOL) block,
align the shape of hole and the shape of shaft.
knob (REC VOL)
(L) block
(L) block
knob (REC VOL) (L) block
Note 2: When installing the ornament (REC VOL),
align five bosses and five holes.
“0” mark
Ornament (REC VOL) setting
Ornament (REC VOL) setting
Knob (REC VOL) block setting
4 washerhead screw
(P
M1.4
u 3.5)
rib
PCM-D100
10
2-6. LED
ASSY
2-7. POWER BOARD-1
Note: Continued on 2-8 (Page 11).
:LUHVHWWLQJ
1 Remove the solder.
[black]
1 Remove the solder.
[yellow]
[yellow]
[black]
2 Peel off two
adhesive
sheets.
3 LED assy
LED assy
AUDIO DA board
three bosses
three bosses
–)URQWERWWRPYLHZ–
5 screw
3 tape
(sub
material)
tape (sub material)
4 stopper
(M1.7
u 3.0)
1 Remove the solder.
(speaker
wire)
[orange/yellow]
2 blind sheet
(circus
jack)
blind sheet
(circus jack)
(circus jack)
1 Remove the solder.
(speaker
wire)
[green/blue]
[green/blue]
[orange/yellow]
POWER board
POWER board
POWER board
– Front bottom view –
:ire VettinJ
:ire VettinJ
center line
center line
%OinG VKeet FirFXV MDFN VettinJ
PCM-D100
11
2-8. POWER BOARD-2
4 flexible flat cable (30P)
(CN2801)
flexible flat cable
(30P)
(30P)
CN2801
– Front bottom view –
3 Move the POWER board
in the direction of an arrow.
knob
(POWER)
(POWER)
switch
switch
knob
(HOLD)
(HOLD)
2 Draw out the jack in the
direction of an arrow.
1 boss
1 boss
Insert is straight to the interior.
Insert is incline
flexible flat cable
connector
connector
flexible flat cable
OK
NG
5 Remove two solders.
(SW board wire)
6 POWER board
POWER board
chassis (POWER)
POWER board
5 Remove two solders.
(AUDIO DA board wire)
5 Remove five solders.
(AUDIO AD board wire)
5 Remove three solders.
5 Remove three solders.
(SYSTEM board wire)
SW board wire
[black]
[black]
SW board wire
[red]
[red]
AUDIO AD board wire
[red]
AUDIO AD board wire
[blue]
AUDIO AD board wire
[green]
AUDIO AD board wire
[gray]
SYSTEM board wire
[white]
[white]
SYSTEM board wire
[red]
[red]
SYSTEM board wire
[black]
[black]
AUDIO AD board wire
[yellow]
AUDIO DA board wire
[white]
AUDIO DA board wire
[blue]
:LUHVHWWLQJ
)OH[LEOHIODWFDEOH3VHWWLQJ
Note 2: When installing the POWER board,
align two switches and two knobs.
Note 1: When installing the flexible flat cable,
check that it have inserted straight.
No slanting after insertion.
PCM-D100
12
2-9. SP BOX ASSY (SP1)
1 boss
2 Peel off the adhesive sheet (SP box).
3 SP box assy (SP1)
1 boss
– Front top view –
2-10. HP VOLUME ASSY
1 knob (play VOL)
knob (play VOL)
2 screw
– Front top view –
shaft
hole
Note 2: When installing the knob
(play VOL), align the shape
of hole and the shape of
shaft.
Note 1: When installing the HP VOLUME assy, push
the DA C board wire under the chassis (upper).
HP VOLUME assy
Knob (play VOL) setting
3 two stoppers
(M1.7
u 3.0)
6 HP VOLUME assy
DA C board
chassis (upper)
4 Remove the HP VOLUME assy
in the direction of an arrow.
5 Remove five solders.
AUDIO DA board
[blue]
[white]
[yellow]
[red]
[black]
:LUHVHWWLQJ
Click on the first or last page to see other PCM-D100 service manuals if exist.